Видео

How many miles are on it to make it needing new bearings and axles

I do my farther 2 times a year I allways use the extractor jack passenger side up a touch make sure you tube is straight I store the tube in garage with a weight on it

Hi ive z zafira a with a similar problem..would this method be sufficient. As i was told tthat the timing belt needs to come off

Really good video this! Did the brakes on the Mrs' Car no problem! Quite right about the retaining clips being a bastard to get back in, though 😂

How is it sliding so easy in... mine needs hammer

If i got this correct not 100% sure but the outer part is FPM dont lubricate it or it will leak and the inner part must be lubricated its APM and seal moving part.

Very nice job. I'll try change the engine in my bike. Thanks

why didn't you replace sump plug washer?

Super labombastic fantastic skolastic 💘

Thanks for the information. I'm embarking on a head gasket repair also. This helps a lot.

Спасибо, всё отлично!

Well done, Joe! Very well explained - and filmed, given that you were (obvs) on your tod. I was looking for this adjustment for a Fiat Punto, and this Focus rear brake arrangement is a dead ringer for that of the Grande Punto. Mick, West Yorks. PS Sanding brake shoes? Please don't. It's both unnecessary (their surfaces will be re-compressed/ re-glazed within seconds of normal use) and a serious health hazard to you.

On the 1.3 the bottom cog of the timing chain is not keyed to the shaft so you can quite easily put the timing out unless the flywheel is locked.... be warned as the 1.2 looks exactly the same.

Nice work-

Can you breakdown a list of tools needed and sizes. Don’t wanna have to buy a whole new toolset

Great video bro thank you so much i love you❤

Great video buddy, ta.

Great video cheers

Did I only notice that at 2:02, your chassis is broken or is it something I don't see clear?

screws ion the trim, just like my car.

Perfectly explained, thank you!! 👍 I'm going to change the bearing on the left side since it's has been shotted by some rough streets...

Thanks Joe. Nice video. I've also got a 1.2 sxi 5 Door in 21b aswell. It's got bout 100,000 mls and runs really nicely. Hope to see you doing more videos like this one. Your a good mechanic and your good at explaining what's required to get it done well. Very professional. Cheers mate👍

Done mine, car just passed MOT, grate video mate

do you turn this screw counterclockwise towards you? to make it tighter for the brake shoes

100 Nm on the axle bolt as the manual states is too much There has been a lot published on this. Greywolf recommends 80 Nm My mate stripped his axle threads with 100 nm and could not get the nut off.

Awesome Video! Tahnks for sharing ! Very informative!

Simple, easy, just what i needed. Goddamn wiper assembly on my grandfather's fiesta caused massive corrosion in the strut mount, possibly the strut itself, but I'll replace both and not take the chance. Should have a grommet in the top from factory

I had to watch 5 min unskippable advertisement to watch this video !😢

I may have missed it but Honda has a hole at the bottom of the water pump to act as a ´telltale´ or signal that the internal mechanical seal on the pump shaft is compromised. It acts as a drain that will leave antifreeze on the floor alerting you to the failure of said seal. If that is the case you should not have welded it. By welding it you will ensure the leakage gets into the engine itself. Not sure if that is what you did but make sure everything is as it should be as antifreeze in your engine oil is a bit of a nightmare.

Very precise and didn't miss a beat!

Good video I'm gonna try my corsa brakes after watching this...

Very nice video! Thanks for the help

Excellent video

My 2015 corsa e 1.4 petrol oil filter looks very different. Must be a different 1.4 engine (even though everything looks the same), I see no other possibility. No need to 'torque' an oil filter at all, have been tightening them for 30 years with just a wrench, never any issues. Don't overthink things.

Just had to get my rear wheel off a few days ago after a nasty incident with a bike cover at 100km/h. While I have it off, I may as well check these little guys. Thanks for the knowledge!

Hi ! Thanks. How many km (or miles) when you had to change your bearings? Greetings from France

I'm missing my fiesta mk 6.5 - 1.6 TDCi Zetec Climate. I used to service my car went through the same process. The Haynes manual is a trust worthy source for nm torque. Although, there were some difference between Haynes manual and Ford recommendations but these were to do with timing belt and cam belt. Haynes manual stated half the mileage of both belts. While Ford recommended the 100k for timing belt, Haynes manual stated 50k. The incredibly things was I managed my personal best of 647 miles on full tank of fuel.

Really helpful! Thanks for doing this video!

Very good guide thank you.

What moment for Drain screw ?

didn't like the fact he just yanked the handbrake up like he did without pressing the button but did it after why😮

Thank you!!

Hi mate, just wondering where you got your handle bars from? Just bought a 07 one of these and the standard ones are sh1t 😂

no criticism but while it's in place I would loosen . the top bolt couple of threads so you haven't got to force that bolt while under while springs are compressed

if they are like the sealey ones. they will be fine

Glad I watched the video even I had to check the filter before I open the box and make sure it didn't rain or until filter was correct in size

Thanks for the video but unfortunately the last person who changed the oil on my car stripped the sump plug what a nightmare

ganz schön versifft und verrostet das Schätzchen - aber saubere Arbeit 👍 welche Stoßdämpfer kannst Du empfehlen? Sachs? Bilstein? Kayaba?

hi was there a washer under the centre nut

Over heat much 😳