Видео

Wonderful video Brother,, keeping it real!!! People please listen to this man. I watch so many of the Big channel throw money away on a lot of upgrades that are not needed!

Just want to say thank to i happen to come across your channel and I watched a few and you inspired me to finally build my own scail rc always wanted to and watching you made me want to get back into the hobby ave I did subscribe

I drove mine around a while. Did wheels. Then tires. Then different covers. Along the way I did the Harley designs vfd swap with a fusion pro along with vfd stance 90mm shocks. It goes and goes and goes. Threw a storm trooper in it and some lighting and boom it’s a killer.

Thanks for the inspiration. Making one rn,not as large because I’m pulling it with a trx4 but still taking a lot of inspiration from yours

Does anyone know where or if i could get a 2010 toyota Tundra crewmax body for a 1/10 scale truck.

Hi. I have watched all your videos and find them entertaining. So I thought I would try to help you. If that sound box is like mine, you can hook it to your computer and add more sounds.

Are you going to take the spacer out of the transmission so you have two speed? I'm in Fla. I don't do rear dig. They don't tell you there's both in the trans and all you have to do is swap the spacer from the dig shift rod to the forward 2 speed shift rod. Or, Get radio with more channels. They should advertise this Jeep has 2 speed in it. I didn't buy one untill I found out, Didn't think it was worth the money if I had to add one, I'm sure they'd have alot more sales!

Hi again from Canada I have a question about what you did to connect the stock drive line to the new axles? I have the SCX10 lll Bronco that I put a scale 4 door hard body Jeep and I tried to put the same axles that you just put on but the pin to hold the drive line on wouldn't start to thread, I have touse the stock drive line because it is all I have. Can you help? Thanks for sharing your videos with us.

Your CG is too high too much spring in your shocks maybe try desert lizards half droop hundred millimeters and you’ll have better luck

Your CG is too high too much spring in your shocks maybe try desert lizards half droop hundred millimeters and you’ll have better luck

I ordered all on your list but what motor and what size tires are you running.

Awesome video I just finished a scx10 pro build its just a roller right now but would love to get your take on it so I know where to go

I want that to be my next RC

I want to say thank you for this video, i very badly want to build a rock crawler, but i do not have the means to build on like you do, so seeing this is refreshing knowing that you can buy an rtr and with minimal effort it can be efficient

Just bought the newish RTR Deadbolt.SCX10.2 Just to se what AXIAL is all about. New wheels and tires decided to stick with brand on wheels and HyRAX tires. Yeah racing 110 mm shocks with a negative droop. Next changing all plastic links and building links from brass. Was very curious to see from a RTR what extreme balances to make it SWEET! Think I made it happen will let ya know!✌🏼🏴‍☠️☠️🎳

Awesome approach, covering all types of builds/upgrades.

Awesome 👌 👏 👍

My friend I watched the whole video carefully and, I'm sorry, but I have to contradict you. First of all you can clearly see from the video that the shoulder of the tires gave way almost completely, I'm talking about the rear ones. This alone contributed heavily to destabilizing the vehicle and making it bend too much. Solution: blue Injora silicone inserts. I agree about making the wheelbase between the tires a little wider, but without overdoing it. When you were at 26cm it was already fine. The second thing that causes problems is too much body height. With those beautiful blue shocks you have raised the body further. By a little but you made the already critical situation worse. Solution: reposition the original shocks at the highest point of attachment on the towers and you will gain just enough to lower it a little, just a little. If that is not enough then little trick. With ties or clamps limit the travel of both the front and rear shocks. The ratio is: a little more limited forward and less at the back (usually) This will lower the body and limit the travel of the shocks if they are pushed equally but will not limit them when one is compressed and the other not. Virtually no-cost modifications. Let me know how it goes and if my advice was helpful. I hope so and have fun buddy

This video was very informative 1 of bit of information I didn't know was about spacing the wheels out changes the face it may start catching as you would thought it would actually less likely to.

Alot of bump steer with those axles and torque twist with the long shocks

Jeep's looking better. l put 15mm brass hub extensions on mine. Better/heavier tires makes a big difference with such a tall vehicle.

Creo que con un poco de peso delante hubiese bastado

Does that have the goofy bent panhard like other scx10iii

Just wondering Mr Waffles. Did you happen to do the math on buying a set of frame rails in a body? And then adding all that stuff I mean honestly that's about the only thing that's not going to get changed by the time you're done except for maybe the transmission. Not being an ass*, just genuinely asking

I am trying to promote you in FB groups but none of my posts get approved. Too bad because this is awesome!

Keep up the good work!! 🤘🤘

I took the body off that ways almost as much as the car itself and it preforms amazing

Use that dig on the stairs pull the front end down

Nice work that a good video I'm definitely gonna throw some new rims and tires on my truck and eventually weights or those axles thumbs 👍

love that jeep

Amen me too buddy bought the same exact color. Actually we went into hour LHS to view over Christmas break and they had the red one. Wife was like ah I was ah we walked out. They ask is there anything we can help you with my wife said like the silver one. He says hold on comes out famous last worlds last one 🤣 dude was not blocking wife looks at me says what are you going to do? Add another fake car to our estate 😂 by the way CJ-5/7 are my favorite vehicle ever

Evening after sauna 👋🙂 nice good video 😁👍

I did a fusion pro in mine...very nice! To make the body easier to get on and off i would suggest fine lazer designs clipless body mount. Takes a little getting used to but works very well.

One thing to watch on longer shocks is the range of travel and spring rate. I replaced the standard FTX OUTBACK 2 (yeah, yeah, shut up😄) with 90mm of the finest Chinesium. I got the lift but with less travel. The Standard had more travel and softer springs resulting in more travel. D'oh🤦🏻‍♂️😆

That thing is awesome. I might have to get one soon lol 🎉❤

Man you just ain't changed in a week lol jk rtr on waffles rc? I kid man i kid killer ta see how you're gonna upgrader

Nice work appreciate the incremental steps so you don't do too much just enough, thanks for sharing

Figured id mention…i built a set of double belly dump trailers for my 1/14 tamiya semi using the 1/2” sq tube. I went to a metal supplier and was able to get two 20ft sticks for $15 each. Home depot charges like $12-$15 per 6ft piece! Save yourself alot of money and get WAY more tube for future projects!!! Live the builds man! Huge inspiration!

Love that beach crawler 😂😂

Nice to see the various changes and testing between each. Cannot wait to see the difference with a brushless setup.

Looks awesome I've been looking at that rc for my next one keep up the awesome videos

🎉🎉🎉

Need a few 1/24 trucks to go on the trailer to get real close to scale looks.

Although the electrical part gets interesting. Turns out the ferrite ring was the answer. Imagine that. EMF another hidden RC issue. RC turns us into scientists. Entry level of course.

You did a good job,looks good 👍👍

Nice cool setup i think that sound box u can hook to a computer and install different sounds and stuff in it thumbs on the build looks cool 😎

Oh & by the way... Youre an aussie now & your name is Woffo

❤

subbed 👍

Hell yeah PBG is one of my favs too 😎🤙🏼