So what im trying to see could the ignition switch gears be the issue because my dash cluster shows the battery light instead of security. & also the PRNDL , gas gauge and coolant temp doesn’t function correctly. i was going to try to move the gears. because my key was getting stuck
Yes I'm home probably a 2002 Chevy Monte Carlo all I can come around is my check engine light 10 seconds later all the gas lights are flash on and go right off what could be my problem
My truck turns on and everything but it won’t go back to off position basically engine off but not the truck I can lower the window 😢 it stays and drains my battery Please help 🙏
it sounds like its going into accessories mode after you turn it off.... try turning and placing your key in different positions and see if it goes to the off mode.... sounds like a bad key cylinder.
See my comment elsewhere (posted 5/20200). It sounds like we have the same problem? If nothing else, try what I did: Turn the key slowly, as at least when it's really cold outside, there is a gap between the ignition circuitry and operation of the starter motor. I can crank on the starter all I want, but without the ignition on, it simply will not start. I am going to get replacement parts to see if I can eliminate this problem. As I write this, I have well over 260,000 miles on my Suburban.
I have a question, my key is stuck in the ignition. I took the cylinder out put a new one and it does the same thing.keys come out when the ignition is out but when I put it into the housing it stays stuck
I have an interesting problem with my 2000 Suburban, related to what you're doing here. I live in Northern Minnesota, so anytime we get below about -7 degrees, I cannot start my vehicle. The key turns just fine, but in the sequence, I s-l-o-w-l-y turn the key past the "on" position (dashboard and ignition lights come on), then all power and lights shut off, then the starter motor turns the engine over. The problem lies in that I can run that starter all I want, but the vehicle won't start, because the ignition circuit is not active. I do not believe it to be the keylock itself (although I am going to replace that at the same time), but rather that there is something loose in the electronic switch mechanism itself. Right now, everything works fine (with one exception), as it is approaching 60 degrees. But my new problem is that I cannot get the radio to send audio to the amplifiers! (In short, I know it's not the radio itself, as a different radio did the same thing when plugged in.) But I am of the opinion that this problem also stems from the switching circuitry, as the vehicle is designed to cut out the radio when cranking the engine. Does this sound plausible, that I will need to replace the switch circuitry? Thanks in advance.
@@snickpickle I'm having the exact same problem with my 06 Avalanche, the key turns just fine. But now as I start to turn the key to fire up the ignition, all power goes out from the dash, then the stater motor just clicks. I don't think it is the lock cylinder, possibly the ignition switch again. Took to dealer and they replaced the starter and ignition switch, worked for a about 2 weeks then happened again. This just started to becoming on ongoing issue since February 2020, got a passlock code so dealer recommended I take out the radio cause it was aftermarket, they reset the passlock code, I removed the radio and after two days it started again. I'm starting to believe it could be the actual passlock sensor in the ignition housing. What did you do to get yours working?
@@Elsrelly still appears to be a starter issue from what you tell me, try jump starting the vehicle and see if anything changes (engine cranks) im curious to see if theres enough voltage in your sytem.
I have Toyota allion, when I turn on the switch, ignition and gaudes light didn't come on but the engine can start.if anyone can tell me how to fix my cat
Hey bud! The problem is between the cylinder and the switch. Why not pull out the cylinder and see what's not working? You haven't even got a name for the part that is the problem because from what I could see the cylinder and the switch both work. It's what's between then that is your problem. For me the cylinder sticks in start and the starter motor keeps running unless you carefully turn the cylinder back to run from start. Good luck.
》》 REALLY---I WILL HAVE TO SEE ANOTHER UTUBE VIDEO TO SEE HOW TO REMOVE THE COVER????? ( YOU FAILED!!! ).. YOU SHOULD HAVE INCLUDED IT IN YOUR VIDEO!!!!° >FAIL
This was the exact video I needed thanks
Exactly what I needed, Thank you
You may be right, I had the same problem and I changed the ignition switch today and that solved the problems.
Great video thank you bro. You saved us hundreds of dollars.❤
You put your left foot in.
You put your left foot out.
You do the hokey pokey.
And turn yourself about.
And that’s how you turn on the truck.
🤣🤣🤣🤣
Thanks for you help god bless you
Exelente vídeo gracias me fue muy muy útil me saco de un gran apuro gracias por tu video
Excellent
I'm having this same problem. What can I do to fix it?? What did you do?? What was the problem??
Bad Cilinder
@@losgarciasadventures1496 Thank you.
,klo
I’m having the same problem but no light on my dash is coming in but all the other lights are on far as the lights
Mine too did u figure out what was wrong ?
@@mikeythakidd1565did you find the solution?
So what im trying to see could the ignition switch gears be the issue because my dash cluster shows the battery light instead of security. & also the PRNDL , gas gauge and coolant temp doesn’t function correctly. i was going to try to move the gears. because my key was getting stuck
Yes I'm home probably a 2002 Chevy Monte Carlo all I can come around is my check engine light 10 seconds later all the gas lights are flash on and go right off what could be my problem
Robert -how did you release the white clip (with brown/green wire) from ignition cylinder?
Get a little pick tool and unlock the lock and it turns and comes out sideways
My truck turns on and everything but it won’t go back to off position basically engine off but not the truck I can lower the window 😢 it stays and drains my battery
Please help 🙏
it sounds like its going into accessories mode after you turn it off.... try turning and placing your key in different positions and see if it goes to the off mode.... sounds like a bad key cylinder.
Thanks!
thats not the ignition switch thats the cylinder
So what was the fix ? Which part needed replaced ?
So I just got the cylinder fixed. It turns everything on, but doesn’t start the truck.
I tried to turn on the blazer via the switch...it didn't work..at the final click all lights go out.
See my comment elsewhere (posted 5/20200). It sounds like we have the same problem? If nothing else, try what I did: Turn the key slowly, as at least when it's really cold outside, there is a gap between the ignition circuitry and operation of the starter motor. I can crank on the starter all I want, but without the ignition on, it simply will not start. I am going to get replacement parts to see if I can eliminate this problem. As I write this, I have well over 260,000 miles on my Suburban.
If you turn the switch,gears,back it shuts the ignition off,if you turn the switch,gears forward it will start it
Did ur stereo stay on after cutting off truck ?
No, everything turns off
@@losgarciasadventures1496 my stereo stays on had 2 people look at it was possible thinking it was that done check all my fuses
BIG HELP THANKS
Man ur funny bro.
Anyone know how I can remove my key from the on position, key got stuck
Same problem here
How’s you fix that
@@moraless_h1367 how did you fix that
@@josh_a.7142took it to the mechanic ended up replacing the whole steering column
@@moraless_h1367 you didn’t go to a mechanic you went to a parts changer
I have a question, my key is stuck in the ignition. I took the cylinder out put a new one and it does the same thing.keys come out when the ignition is out but when I put it into the housing it stays stuck
Same here
I have an interesting problem with my 2000 Suburban, related to what you're doing here. I live in Northern Minnesota, so anytime we get below about -7 degrees, I cannot start my vehicle. The key turns just fine, but in the sequence, I s-l-o-w-l-y turn the key past the "on" position (dashboard and ignition lights come on), then all power and lights shut off, then the starter motor turns the engine over. The problem lies in that I can run that starter all I want, but the vehicle won't start, because the ignition circuit is not active. I do not believe it to be the keylock itself (although I am going to replace that at the same time), but rather that there is something loose in the electronic switch mechanism itself. Right now, everything works fine (with one exception), as it is approaching 60 degrees. But my new problem is that I cannot get the radio to send audio to the amplifiers! (In short, I know it's not the radio itself, as a different radio did the same thing when plugged in.) But I am of the opinion that this problem also stems from the switching circuitry, as the vehicle is designed to cut out the radio when cranking the engine. Does this sound plausible, that I will need to replace the switch circuitry? Thanks in advance.
Oh I just got rid of a month ago
@@SyriusXR7 It's all about the timing, right? I guess I missed with this comment by about a month. Sorry! :-)
@@snickpickle I'm having the exact same problem with my 06 Avalanche, the key turns just fine. But now as I start to turn the key to fire up the ignition, all power goes out from the dash, then the stater motor just clicks. I don't think it is the lock cylinder, possibly the ignition switch again. Took to dealer and they replaced the starter and ignition switch, worked for a about 2 weeks then happened again. This just started to becoming on ongoing issue since February 2020, got a passlock code so dealer recommended I take out the radio cause it was aftermarket, they reset the passlock code, I removed the radio and after two days it started again. I'm starting to believe it could be the actual passlock sensor in the ignition housing.
What did you do to get yours working?
Any fixes? Lol I have the same problem with my Yukon
Did you ever fix this problem I have to do the same thing with my s10
Yes had to pull the steering wheel out replace ignition then we sold it.
My 2001 tahoe won't start but all the lights come on i changed the starter and my spark plugs and wires still no crack help me
When you turn the key does it have resistance or does it move freely? When you turn the key do your hear a click in the engine?
@@losgarciasadventures1496 I hear a click but thats it all lights come on and radio no start tho just one click
@@Elsrelly still appears to be a starter issue from what you tell me, try jump starting the vehicle and see if anything changes (engine cranks) im curious to see if theres enough voltage in your sytem.
@@losgarciasadventures1496 still not starting its a brand new starter
@@Elsrelly did you check your starter relay and fuses?
Qué ago si se activa el seguro i no puedo mover la palanca de canbio
Ayúdame mi bam es GMC 2006 estoy muy lejos de casa i no puede moverme gracias saludo de masachusett
Did it crank before you had to do it ?
no, when you would turn the key it would just slide like if it was loose no tension.
Mine was the same as yours, but all I did was turn the gears until the lights went off,put the key cylinder back in and it starts
I have Toyota allion, when I turn on the switch, ignition and gaudes light didn't come on but the engine can start.if anyone can tell me how to fix my cat
Hey bud! The problem is between the cylinder and the switch. Why not pull out the cylinder and see what's not working? You haven't even got a name for the part that is the problem because from what I could see the cylinder and the switch both work. It's what's between then that is your problem. For me the cylinder sticks in start and the starter motor keeps running unless you carefully turn the cylinder back to run from start. Good luck.
ya my cylinder sticks in start and the start motor keeps running, but the car will not start, how did you fix it?
Want start
You're you're not much help if you keep saying go look at another video why do you even post it. Not going to get much,👍
I have a question
Whats up?
No key in tumbler get it out
》》 REALLY---I WILL HAVE TO SEE ANOTHER UTUBE VIDEO TO SEE HOW TO REMOVE THE COVER????? ( YOU FAILED!!! ).. YOU SHOULD HAVE INCLUDED IT IN YOUR VIDEO!!!!° >FAIL
This should help ruclips.net/video/dBnOaExxHB8/видео.html
African American engineering at its finest my brown brotha
Great video thank you bro. You saved us hundreds of dollars.❤