Dryer Belt Replacement - Duet/HE3 Dryer Repair
HTML-код
- Опубликовано: 20 окт 2024
- This video provides step-by-step repair instructions for replacing the belt on a Duet/HE3 electric dryer. The most common reasons for replacing the belt are when the dryer makes noise, won’t start, or the drum won’t turn at all.
Click here to purchase part #661570:
www.repairclini...
Additional dryer repair, troubleshooting tips, help with finding your model number and part replacement videos can be found on our website:
www.repairclini...
All of the information for this dryer belt replacement video is applicable to the following brands:
Kenmore, Whirlpool, Maytag, KitchenAid, Amana, Crosley, Inglis, Admiral
Connect With Us!
plus.google.co...
/ repairclinic
/ repairclinic
/ repairclinic
Join our free VIP email list for discounts and money-saving tips: tinyurl.com/pnn...
Check out our blog: www.DIY.RepairC...
Don't forget to like and comment on this video, and subscribe to our channel!
![Chino Pacas - Modo Capone (with Drake & Fuerza Regida) [Video Oficial]](http://i.ytimg.com/vi/zjv8TQ0gBkg/mqdefault.jpg)
Thank you! I was able to replace the belt myself with the help of this video.
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Great video. I replaced belt on Kenmore HE2 following your step by step instructions in 30 minutes. Thanks for the help and saving me a service bill.
Used this to help with my SAMSUNG dryer. Mostly the same, couple extra screws. This is the most helpful video. Watched the video, spent less than $30 on the belt, watched video again. Thats it. SAMSUNG people wanted $100 for diagnosis, $250 for labour, and $50 for the part (go figure). Took me about an hour and a half. Thanks so much!
Great video! Just saved a lot of money by replacing the dryer belt ourselves.
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
One of the best repair videos I've ever seen !
And where did all that extra room come from to put the belt on? Not there on my HEB model the blower housing is in the way !!
I just replaced the drum belt on my Kenmore HE2 dryer and the video was very helpful!
These repair videos are AWESOME! I bought a dryer maintenance kit for my Duet dryer and replaced my drum rollers, my belt, and my idler pulley very quickly. My dryer was a bit different...maybe the model wasn't exactly the one on the video, but it was close enough that I could follow along. I went from the squeakiest dryer on the planet to the quietest! It was the idler pulley!
Thanks guys...good maintenance videos allowed me to "do it myself" for $47 instead of calling a maintenance tech for hundreds!
J.
That's great! We're happy we could help!
For anyone still watching this video, one thing. Starting at 00:30 timestamp, my washer had a few key differences: I have the plastic tabs, as shown, but they are secured by two screws (not shown). To gain access, you need to pop the plastic tabs out, and then come up underneath the plastic housing to gain access to the screws. Otherwise, my unit was basically as shown.
Thank you for posting this and for mentioning which side of the belt faces the drum! I could not have completely torn apart my HE3 dryer to replace the belt without this video. The pulley is also tricky and the video helped me get it right.
And who are the 23 people that down voted this video? Makes no sense.
Thank you for the helpful step by step instructions.
Thanks for the great video. You have once again saved me money. Please keep making these videos.
Thank you. Worked with these very easily understood instructions.
$7 or $700? We chose to fix the dryer and only spend $7. Thank you for the video!!
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
My model HE3 was slightly different, but this video was definitely helpful enough to get the job done. The key differences were the way the electronics were held in place and the moisture sensor connector. But overall it was exceptionally helpful and saved me the cost of a repair visit. Belt was about $25 including shipping so a cheap repair.
Jacob Warren We're happy to help!
So I know this is old but I feel I have to say thanks cause this helped me fix my dryer that for me will be 17 yrs old in September lol
very good video He helped me change the strap of my dryer. I congratulate you
I yet tried replacing the belt on my whirlpool duet dryer. First time, it lasted 2 weeks, tried 2 more times and the dryer doesn’t spin under load. The grooved pulley on mine seems awful small. I wonder if it’s throwing belt off, or it wore the edge off the side of the puller they kept it on.
Excellent video! Will definitely use y’all for future repairs!
Great video. I used it to replace the belt on my HE2 dryer works perfectly.
Sweet thanks Brian!
The video is great and worked well to replace the belt. Unfortunately the display consol did not light up or work after the procedure- something went wrong and I must have damaged something inadvertantly although everything went smoothly. Any idea what might have gone wrong and what to check first after wiring ect. It turned on after the intial belt breakage and gave just a "click" sound which gave me the clue to look at the belt. After replacing the belt is when it stoped turning on. Thanks for your help.
I would start with the wire harness and just check the wires to see if one pulled off somewhere. There is not a wire or harness plug that frequently comes off when installing the belt.
I’m having the same problem.
Awesome. Just fixed my ancient speed queen, thank you!
You're welcome!
RepairClinic.com m
Hardest part is getting that dang harness apart. Any tips?
FYI, for the wire harness clip, where he uses a screwdriver to separate them, please note it can be separated using pliers. Gently squeeze the narrow sides together, this will have the effect of bowing out the long sides and allowing the easy separation of the two clips.
Also, the video shows only one harness clip (mentions two, but shows one), but there are two. Also, if like mine, your wires are securely fastened by a wire tie of sorts, the stock ties can be opened, they are only snapped shut around the wires.
I didn't say it in my last comment, but thanks for the video; it helped a lot.
Great info, I ordered a kit and replaced the rollers and belt. But now I get an F-26 code and a “sensor” light…🤯
First, make sure all of your wire connections to the drive motor switch are in the correct locations, securely attached, and not damaged.
Then follow these steps:
1. Power unit down by turning off the circuit breaker(s) for one (1) minute.
2. Power unit up by turning on the circuit breaker(s).
3. Start a time dry cycle.
4. Monitor the dryer for one (1) minute to ensure the error code does not display again.
Thanks, you help me a lot fixing my dryer. Crystal clear video.
Now to see how easy this is ACTUALLY going to be, but definitely helpful seeing what needs done. Thanks 🔧🔧RepairClinic🔧🔧!
EDIT: Few differences on the one I helped my friend fix - control panel plugged in via ribbon cables and screwed installation. Model you had here may've been a couple of yrs newer. We were able to do the job without pulling the machine out, that's the main thing I was glad of. Being agile is kind of necessary for that to be a thing, but we 🐉 have that down. >>:=p
You're welcome! Thank you so much for your support!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Thanks for your expertise!!!
You saved me 150.00 🍸🍸
Great Video, just ordered a replacement. Question: if the belt breaks, like in my case, is there a safety switch that prevents the dryer from starting at all? I tested all fuses/sensors I could find and i was getting no reading from the Thermistor (ordered one too). The machine stopped working while drying a batch.
I believe there is.
While you’re messing with the belt tensioner wheel you will hear what sounds like a switch clicking.
What’s weird is that (If I’m correct about the switch) it just prevents the motor from starting and doesn’t throw a code.
@@SenorDennis that is exactly the case.
Thanks for the help, it was a success! Used your site before and will again.
Thank You
Thank you very much for sharing! I have successfully changed my belt
How Do I dis connected the Wire harnesses?
Thank you , great video , finished my repair.
Excellent repair video, thanks!
If you go to our website and enter your model number it will show parts (and videos) compatible with your model.
Have an he2, but this worked beautifully. Thank you!
We're happy to help!
It's our pleasure Jason!
Happy to help!
Thank you. I have a HE 2 and this video was very helpful. Thanks again.
Super helpful!!!!
You're welcome! Thank you so much for your support!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Thank you.
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
What is the repair part number for the belt ? Would this part work for He2?
I'd advise putting model years in the description. This video applied to about 60-70% of the procedure needed to disassemble the Kenmore HE3 I purchased in 2003. I wasted probably 15-20 minutes trying to follow the 1st half of the video. Otherwise, it was still helpful, but keep in mind your model may be differently configured...perhaps quite a bit.
+K Webster Thank you for the feedback.
? for you, my belt looks fine, but i get a foul smell, pretty much like burnt rubber. I dont think its the motor. Do you suggest the belt as an inexpensive fix?
A belt on a dryer would have to either be stretched significantly or the drum would be hard to turn for the belt to burn. Take the dryer apart and check all the drum supports and the idler pulley to make sure they are working properly. If they look good, it wouldn’t be a bad idea to replace the belt and see what happens. If the motor was causing the smell, it would usually not smell like rubber. Also the motor would usually start getting hot and cutting out on the overload, if it was going bad.
+Rob Christensen Is the small wheel just above the electric motor Watch the video when he install the belt. That small wheel it burn after a long use. I just changed one recently.
Very helpful video thanks for making it
worked like a charm thank you for the vid not hard to do at all and i used this on a 2011 model samsung dryer
Like Denis Lara, my control panel is also different. How do I remove it?
If you go to our website and enter your model number it will display all of the parts we have available for your dryer. If we have a video for your part it will be there.
That's great Wayne!
I have to ask. Why not just access the belt and pulley from the rear of the unit and avoid all of the front of unit disassembly/reassembly.?
+K Webster No answer?
+K Webster Just replaced the belt. Accessing from the back is probably equally time-consuming.
If you're only replacing the pulley, then accessing from the back is by far easier. But if you're replacing the belt as well, the front may be the way to go. I've not tried to access the open rear end of the drum from the rear, which would be required to get the belt over the drum. When replacing the belt, I followed the procedure in this video but also took off the back for very easy access to the pulley when threading the belt. Had to laugh when in this video, for a view for the camera, they threaded the belt with the drum removed. Seemed impossible to me to do the threading with the drum in place but I'm sure it's doable.
Excellent thank you!!
+Robert Gabriel Thanks.
thank you
Nice 👍🏻
I love you