Woooooo! Thanks man just opened up mine too. Located the fuse put a thin copper wire closed it up. Tried fresh water and yes it's working fine.. Thank you so much
MAN! NEVER work inside a microwave workout first discharging the capacitor! The high voltage and current coil KILL YOU INSTANTLY. And NEVER do what he did. Microwaves sometimes have two fuses - both cheap to replace. If one in the fuse holder is soldered in, then replace the fuse holder and replace the fuse with one of SAME amp and voltage and slow or fast blow rating. NOTE: the fuse blew FOR A REASON - the circuit drew to much current. ALWAYS install a voltage surge protector on virtually all home appliances because control boards are quite suspectible and expensive to replace.
Please when u want to make it (actually maybe me too) First : 1. Unplug . Dont use it ehile running . Transformer contains high voltage but also current !!! 2. Discharge capacitator. He can may be charged to 2kV !!! Unplug second fuse with something good isolate it . Than short 2 capacitator terminals . Be careful zo not touch it . Just be sure the capacutator is duscharged . There can be more problems than blown fuse - but when the microwawe cant be turn it on its propably the fuse . Also dont use improvised fuse . Than check the door switch . It should be clicking (i dont really know how to check the switch just saw some video) . Most of information is from channel DiodeGoneWild No add - no hate zo this channel EDIT: Thanks for heart
Perfect! Problem solved if I can get hold of a new fuse. Update: Couldn't buy it in my country (Norway) so sent for 10 pieces from China at $2.80. Insanely cheap.
Brilliant. Checked fuse had gone. Ordered new ones repaired the same day. Thanks. Be carefull of capacitors though, if unsure what you are doing leath unplugged for while till they discharge
🤔hmm, I believe the 2nd fuse had blown off (in the plastic case) and you replaced by modifying it with a fine wire of the same resistance. Should the fuse wire blows it will burn the casing in which it is encased. You should at least wrap it with a heat resistant or fire proof sleeve
It will be better if you watch a video on RUclips itself . just write ( how to discharge a microwaves capacitor ). So you will be able to learn it safetly.
Question, how is touching that wire inside the plactic box fixingbthe heat, it doesnt make any sense as all you done was just touch a bit of wire with the screwdriver 🤔
@@shanepankhurst9958 thats true ...i try my best to hold onto old equipments as far as possible ..but then at last due to the sheer market pressure ive to give it up as i face many problems (old technology/ no spare parts etc) ..but u r rite
My turn table was not spinning, so I took the motor apart and fixed it. Later, the door switches were arching and blew the fuse as a result. So I picked up someone else's microwave oven that was on the curb being disposed of. All of its switches and fuses were OK and were the same as mine, so I replaced my dud parts with these. Total repair cost, $0.00.
I bought my oven as a cheap 1.1 cu ft stainless steel $45 "DEMO" oven. But, it turned out not to be a demo after all, but was a partially dead oven. The keyboard only half worked. Rather than go through the hassle of taking it back and sorting this all out, I took it apart and cleaned the keyboard strip connector contacts, and cleaned the keyboard connector contacts that were located on the controller board as well. I then reassembled the oven, and bingo, it was working 100%, and it still is working today many years later.
Hey it worked thanks a lot 😊.. it was helpful especially during this lockddown period when u can't find repairer. Had hack the fuse, will replace asap after lockdown is over.
I am confused, How did you fix it? You didn't replace the fuse, and the wire was still lose on outside. It seems like that fuse was tampered with before.
Yes, I fixed the microwave before filming this video. After the microwave worked I started filming and the fuze was working and I only showed wich one you need to change.
NTP Vlogs is my channel: specialized in sharing actual repair of Panasonic inverter microwave oven, ... you share with each other to learn from each other's experience. Thank you for your support. I have registered your channel. thank you.
Actually, the high current and voltage would KILL YOU INSTANTLY! Yes, always use a screwdriver with a well insulated handle to to discharge the capacitor BEFORE soon anything else! There is a reason special screws are uses to attach the cabinet.
NTP Vlogs are their channels. share repair microwave oven Panasonic inverter, fan steam brother share learning mutual experience. your channel is very useful. remember to register your channel. thanks.
A good advise before you touche anything inside the microwave parts .You should have been discharged the capacitor then touched the fused . You are luck you had not been electro shocked.High voltage store in capacitors. .....Must discharged before examine anything in microwaves.
Much easier fix with lower risk of electrocution: press down lightly on the top right corner of the door. Sometimes all that's wrong is the door lock and this should engage it.
Hi @@DanielH :) I will check it for secondary fuse but I doubt it since I remembered checking for all possible fuses as secondary. The magnetron might be the culprit I suspect that is the most probable cause of not heating. This was brand new then used 1 time only for heating a whole chicken after that usage of my schoolmate here in the house its not working anymore and has been stocked for a year. So I checked it and replaced the fuse lately and it has light and turning. When I try to heat it a food no heating occurred. Thanks
i have a FIRST1 MICROWAVE model FMW-512 pretty much the same set up as far as parts are concerned as the one that you have... the FUSE HACK WORKED! but how long is this gonna last though? or should i just buy a new fuse?
I'm just going to try replacing the first fuse you pointed out. I'm not gonna do the wire thing too dodgy for my liking. Is there much chance of my heat returning just by replacing that first fuse? As my delivery won't be until Monday now.
Hi, can someone tell me how to pull out the fuse. It has metal case around (Sharp microwave) , I can't seem to figure out. I can see fuse wire inside the clear glass fuse that its broken, just can't pull out the fuse. Thanks!
I have 2 my old one, and 1 I found this 1 working but no heat, my old one works fine but bottom is rusting to the point it has hole's lol , old 1 has this fuse but new one doesn't! ! Just my luck as was hoping to swap the fuse if the same? And bob's my uncle! ! Any ideas? Or advice? Working rusted 1 is tesco brand and 1 with no heat is hotpoint! I've had a good look into it but couldn't find any real help?
NTP Vlogs are their channels. share repair microwave oven Panasonic inverter, fan steam brother share learning mutual experience. your channel is very useful. remember to register your channel. thanks.
Where is the warning saying that microwaves contain high voltage parts They can be deadly even when unplugged, unless handled correctly Unless you are a qualified expert, don't attempt to get into its inner workings. try heating the water of glass.. if it's not heating then it has a serious problem. buy you a new one
No you don't need to be an "expert" you just need to know how to discharge the capacitor which is very simple. If you can't do something as simple as that you probably deserve to be electrocuted.
NEVER DO ANYTHING SHOWN IN THIS VIDEO. SO MANY BAD IDEAS ARE SHOWN IN THIS VIDEO. THIS VIDEO SHOULD BE REMOVED. MORE PEOPLE ARE KILLED TRYING TO FIX THEIR OWN MICROWAVE THAN ANY OTHER HOME APPLIANCE!!
Likely not lethal but you will get hell of a shock :)this guy is very unprofessional, I thought he was going to stab himself with that screw driver trying to open the fuse holder.
Why is this the only guide that mention changing the secondary fuse all the things only mention the magnetron, diode or door switch, fucking useless pages, Anywho thanks you for confirming our suspicions
What you would like to know? My microwave was working but no heating, so I changed that fuse you see in the video. If you don't have that second fuse, then the problem is somewhere else. Thanks for your commnt.
Thank you so mutch i fix may microwav by myself
Glad I can help.
Did u change small bottle from sa safetybox or keep at it is?
@@akinto5701
No i dont change it
Only change the fuse wire
Great video. Once he pulled out the drill I was on my way to Amazon. 30 years is a long time for Old Betsy. Time to move on...😔
I just applied your repair method and my microwave is now working soooo fine.
Thank you a lot
Thanks for this great video. It's amazing that a video of 7+ years came to my rescue today.
Glad to help
Woooooo! Thanks man just opened up mine too. Located the fuse put a thin copper wire closed it up. Tried fresh water and yes it's working fine.. Thank you so much
MAN! NEVER work inside a microwave workout first discharging the capacitor! The high voltage and current coil KILL YOU INSTANTLY. And NEVER do what he did. Microwaves sometimes have two fuses - both cheap to replace. If one in the fuse holder is soldered in, then replace the fuse holder and replace the fuse with one of SAME amp and voltage and slow or fast blow rating. NOTE: the fuse blew FOR A REASON - the circuit drew to much current. ALWAYS install a voltage surge protector on virtually all home appliances because control boards are quite suspectible and expensive to replace.
How to discharge the capacitor
Please when u want to make it (actually maybe me too)
First :
1. Unplug . Dont use it ehile running . Transformer contains high voltage but also current !!!
2. Discharge capacitator. He can may be charged to 2kV !!! Unplug second fuse with something good isolate it . Than short 2 capacitator terminals . Be careful zo not touch it .
Just be sure the capacutator is duscharged . There can be more problems than blown fuse - but when the microwawe cant be turn it on its propably the fuse . Also dont use improvised fuse . Than check the door switch . It should be clicking (i dont really know how to check the switch just saw some video) .
Most of information is from channel
DiodeGoneWild
No add - no hate zo this channel
EDIT: Thanks for heart
Thank you so much. Tried this and it worked! Saved me having to buy a new microwave.
Perfect! Problem solved if I can get hold of a new fuse. Update: Couldn't buy it in my country (Norway) so sent for 10 pieces from China at $2.80. Insanely cheap.
China is cheap but the shipping time kills it. I have to Wait between 2 weeks and 2 months for the items to arrive
@@DanielH Yeah, I survive by dusting off an old microwave I had lying around in the garage.
Strange. Commonly available in hardware stores and home/building supply centers I'm USA.
Brilliant. Checked fuse had gone. Ordered new ones repaired the same day. Thanks. Be carefull of capacitors though, if unsure what you are doing leath unplugged for while till they discharge
🤔hmm, I believe the 2nd fuse had blown off (in the plastic case) and you replaced by modifying it with a fine wire of the same resistance. Should the fuse wire blows it will burn the casing in which it is encased. You should at least wrap it with a heat resistant or fire proof sleeve
It will be better if you watch a video on RUclips itself .
just write ( how to discharge a microwaves capacitor ).
So you will be able to learn it safetly.
Farwest2208 fardeen will do
Question, how is touching that wire inside the plactic box fixingbthe heat, it doesnt make any sense as all you done was just touch a bit of wire with the screwdriver 🤔
No, i changed the fuse that is on that wire.
as an electrician its also important to find out why fuse blew or else same thing may happen again.
I think because of small conductive materials found in glasses and decorative plates
I just throw them away and buy another $100 microwave. Didn't know they could be fixed. Mind blown
old equipments used to last forever ...lifelong..but today's new substandard sh8t dsnt last more than couple of yrs
@@idontcarei we keep consuming and making it possible
@@shanepankhurst9958 thats true ...i try my best to hold onto old equipments as far as possible ..but then at last due to the sheer market pressure ive to give it up as i face many problems (old technology/ no spare parts etc) ..but u r rite
Even when unplugged then capacitor can kill you. Be careful.!!!!!
Discharge the 2000v capacitor before doing anything on the high voltage side. If you don't know what this means then don't even take the cover off.
My turn table was not spinning, so I took the motor apart and fixed it. Later, the door switches were arching and blew the fuse as a result. So I picked up someone else's microwave oven that was on the curb being disposed of. All of its switches and fuses were OK and were the same as mine, so I replaced my dud parts with these. Total repair cost, $0.00.
I bought my oven as a cheap 1.1 cu ft stainless steel $45 "DEMO" oven. But, it turned out not to be a demo after all, but was a partially dead oven. The keyboard only half worked. Rather than go through the hassle of taking it back and sorting this all out, I took it apart and cleaned the keyboard strip connector contacts, and cleaned the keyboard connector contacts that were located on the controller board as well. I then reassembled the oven, and bingo, it was working 100%, and it still is working today many years later.
thanks mr daniel ... my microwave can work again...
Laurencia Ivana unnhgfxzPa_/4$!!!!!! Pzpzfn iikm
Jhzzyuhynbnhhhhxzdss
I threw mine in the window and it worked :D
Haha
Hey it worked thanks a lot 😊.. it was helpful especially during this lockddown period when u can't find repairer. Had hack the fuse, will replace asap after lockdown is over.
Glad I could help you. Stay safe
I am confused, How did you fix it? You didn't replace the fuse, and the wire was still lose on outside. It seems like that fuse was tampered with before.
Yes, I fixed the microwave before filming this video. After the microwave worked I started filming and the fuze was working and I only showed wich one you need to change.
Yes, i fixed the microwave before making this video. Video was made few days after the microwave was fixed. Sorry about that misunderstanding
Thanks very much - microwave now working fine. Great stuff
STOP! ALWAYS discharge capacitors BEFORE doing any work on such electronics.
Nice Video but you HAVE TO discharge the HT Capacitor first otherwise anyone trying this repair will get a very nasty shock.
NTP Vlogs is my channel: specialized in sharing actual repair of Panasonic inverter microwave oven, ... you share with each other to learn from each other's experience. Thank you for your support. I have registered your channel. thank you.
Actually, the high current and voltage would KILL YOU INSTANTLY! Yes, always use a screwdriver with a well insulated handle to to discharge the capacitor BEFORE soon anything else! There is a reason special screws are uses to attach the cabinet.
Rock the eff on! My microwave stopped working this AM. This will be my weekend project. Cannot wait!!
Good luck
Fuse also blows if there’s a power surge
NTP Vlogs are their channels. share repair microwave oven Panasonic inverter, fan steam brother share learning mutual experience. your channel is very useful. remember to register your channel. thanks.
This should not be attempted without discharging the capacitor located next to the fuse in the microwave which stores electricity even when unplugged.
You're right about that
Thank you my microwave is now working
A good advise before you touche anything inside the microwave parts .You should have been discharged the capacitor then touched the fused . You are luck you had not been electro shocked.High voltage store in capacitors. .....Must discharged before examine anything in microwaves.
how do you discharge a capacitor?
Sir, my microwave is making warm only and not heating. Do you know what is the problem? Thanks
Much easier fix with lower risk of electrocution: press down lightly on the top right corner of the door. Sometimes all that's wrong is the door lock and this should engage it.
Would it still start and spin as normal though if that was the case? Mines working as normal except there's just no heat
Helen Wallis I thank you - such an easy fix and I never would have thought of it. Very many thanks
I did replaced that fuse but it keep blowing up when I start the microwave up.
I didn't understand the problem & what was fixed in the microwave sorry guys.
I had it replaced, there is now current and light and its turning but still no heat?
Is there a second fuse that might went off?
Hi @@DanielH :)
I will check it for secondary fuse but I doubt it since I remembered checking for all possible fuses as secondary. The magnetron might be the culprit I suspect that is the most probable cause of not heating. This was brand new then used 1 time only for heating a whole chicken after that usage of my schoolmate here in the house its not working anymore and has been stocked for a year. So I checked it and replaced the fuse lately and it has light and turning. When I try to heat it a food no heating occurred. Thanks
i have a FIRST1 MICROWAVE model FMW-512 pretty much the same set up as far as parts are concerned as the one that you have... the FUSE HACK WORKED! but how long is this gonna last though? or should i just buy a new fuse?
Mine works for few years I think.
@@DanielH thank you..
Thank you so much. Your video saved me £55 I was going to buy one that day! 👍
Glad you saved some money. 🙂
Just followed this tutorial and it actually worked 😅
Glad it helped you 🙂
Thanks Daniel - works like a charm! Greetings from Zambia!
Glad I could help you. Stay safe
Doesn't really help unless you know why the fuse has blown in the first place.
I hope this works with mine, gonna give it a go before buying a new one. Thanks so much for sharing your knowledge mate❣️❤️🔥🙌❤️🔥
step by step explainingwould have helped me.
ruclips.net/video/SGJ0hvi6Aj4/видео.html here is what you need
But my problem is after putting metal plate inside the microwave, my microwave did not heating, so does your way can fix my problem?
You saved my day, thanks a. Lot
I'm just going to try replacing the first fuse you pointed out. I'm not gonna do the wire thing too dodgy for my liking. Is there much chance of my heat returning just by replacing that first fuse? As my delivery won't be until Monday now.
Really helpful
Thanks a lot for the video 👍🏻
thank you👍
Thank you I found the fuse and it was blown so I ordered replacement. will update comment when shippment arrives.
The fuse fixed it.
Yeah dont think i will do that.so here i come Wallyworld...good interesting vid though!!
The choice is yours. Good luck
what if diode is fine, heating and sniping won't work? how to check synchronous motor?
Does heating works if sniping motor won't work?
Hi, can someone tell me how to pull out the fuse. It has metal case around (Sharp microwave) , I can't seem to figure out. I can see fuse wire inside the clear glass fuse that its broken, just can't pull out the fuse. Thanks!
After 20 years, buying new. Will old in garden contaminate growing spuds?
Great video, I would over look that 2nd fuse.
Thanks so much
I have 2 my old one, and 1 I found this 1 working but no heat, my old one works fine but bottom is rusting to the point it has hole's lol , old 1 has this fuse but new one doesn't! ! Just my luck as was hoping to swap the fuse if the same? And bob's my uncle! ! Any ideas? Or advice? Working rusted 1 is tesco brand and 1 with no heat is hotpoint! I've had a good look into it but couldn't find any real help?
Cause why the fuse blown.
Microwave heating karta hay lekin automatic timer botton previous side per ghoomta hay
Please any info
I worked! Thanks a lot!
did not cover lot others like Magnetron, etc.
Transformer, triad, magnetron, thermostat, bad fan motor, fan belt.
got same problem, same fuse, thx
you forget to discharge the hv capacitor!
i'm getting old :(
Daniel H. good ! means no capacitor has finished you off ;) thanks for video
.
Very good. I repair my oven. Thanks
Glad I've been able to help
Thanx thanx thanx vry very thanx bro. You save my money I am so happy 😊
NTP Vlogs are their channels. share repair microwave oven Panasonic inverter, fan steam brother share learning mutual experience. your channel is very useful. remember to register your channel. thanks.
Where is the warning saying that microwaves contain high voltage parts
They can be deadly even when unplugged, unless handled correctly
Unless you are a qualified expert, don't attempt to get into its inner workings. try heating the water of glass.. if it's not heating then it has a serious problem. buy you a new one
No you don't need to be an "expert" you just need to know how to discharge the capacitor which is very simple. If you can't do something as simple as that you probably deserve to be electrocuted.
Works every ttime. Great cheat. :D
Easy fix, eh? Not so easy when it’s a built-in.
Take it out, its not fused into your kitchen
Works a treat
I bet his wife loves him .....he is "good with his hands"......lol
Sir,my oven working ligh also but not heating, plz help me,what I do
Watch the video and check the fuse. Change it and might work
if fuse is ok,whats next to be check?
Nice knowledhe sharing.....keep it up....
I'm always advocating for a kill count icon on RUclips videos. Be careful of the capacitor, humans.
Naughty RUclipsr, naughty!
Rawr
thnx for video. I seem to have the same problem, but what is the fuse type number so I can order it online?
jim bean i don't have that infomation. sorry.
Daniel H. n
just saw the rating of the fuse.. 5kv 0.7A
NEVER DO ANYTHING SHOWN IN THIS VIDEO. SO MANY BAD IDEAS ARE SHOWN IN THIS VIDEO. THIS VIDEO SHOULD BE REMOVED. MORE PEOPLE ARE KILLED TRYING TO FIX THEIR OWN MICROWAVE THAN ANY OTHER HOME APPLIANCE!!
Spot on, thanks, all fixed. 😎
Thanks a lot
I can't find a second fuse. Someone help please 😭
good lord please dont go near the magnetron without discharge
I know
There's no way all of these commenters with exactly 4 numbers at the end of their screen names aren't bots
You think I paid someone to boost my video?
Capacitor is not drained first. Potentially lethal
Hi how do you do this? Thanks ☺
Likely not lethal but you will get hell of a shock :)this guy is very unprofessional, I thought he was going to stab himself with that screw driver trying to open the fuse holder.
thanks i fixed my microwave
So helpful
Sooo all you did was move the little wire around?
No, you need to change the fuse that's on that wire.
Daniel H. wait how do u do that? i don’t think you did it in the video? the wire was already there wasn’t it?
The wire was an improvisation until I got a new fuse.
ruclips.net/video/SGJ0hvi6Aj4/видео.html here as updated version with subtitles and better explanation
Daniel H. thank u so much
Stil not working.
Bad very bad demonstration you need to be explaining what you're doing we don't need the music playing
Try this one. With explanation and subtitles. Good luck
ruclips.net/video/SGJ0hvi6Aj4/видео.html
Thank you my friend....
Says easy fix but it's so technical
Aneeb Aneeb 3 screws and a fuse?
Thanks ❤
Thank you
Thank you so much
You're welcome ☺️
Thank u somuch❤
man.... I sure feel sorry for the person who actually thought this was infofmative
Ok man...
Why is this the only guide that mention changing the secondary fuse all the things only mention the magnetron, diode or door switch, fucking useless pages,
Anywho thanks you for confirming our suspicions
I've only one fuse what should i do ?
SyrianGamers go to a specialist. try a local repair shop. best I can help you with
Thanks bro
hey it went off what happed to it lol , hope every thing is ok lol
Nice
Just nice music but no explanations. What's going on?
What you would like to know? My microwave was working but no heating, so I changed that fuse you see in the video. If you don't have that second fuse, then the problem is somewhere else. Thanks for your commnt.
Daniel H. My midea microwave not heating
That’s A $50 microwave 😂
Why buy a new one when it can be fixed?
waste of time
For you maybe. But for other people was useful and got their microwaves fixed. Thanks for the comment.