Sir you made me laugh because your approach and reactions are exactly how I would think-and speak when I’m attempting a repair. Good job and thank you for the tutorial.
Some capacitors have a resistor inside (10Mohms) that safely discharges them in a few seconds. Also, the high voltage diodes can't be tested with a regular multimeter alone. They need to pass a higher voltage than what the multimeter can offer, anything more than 9V. The multimeter will test the voltage going out of the diode: forward it will drop around 5V, and won't drop anything in reverse.
HV Diode have several diodes in series in order to have a HV rating. A multimeter diode tester is only good for a single junction diode with a forward junction drop below 3v to 4v. Use a 9v battery in series to do a HV diode test.
@@quintinplaza, I knew that was not correct. You can't measure a microwave diode with a multitester without injecting some voltage through it. Nine volts will do.
Testing a high voltage diode is not as simple as using the multimeter's diode test function. It showed open circuit in both directions because the multimeter's voltage is not high enough to overcome the voltage drop of the diode. Here is a video that shows a way to measure it with a regular DMM: ruclips.net/video/1pp4LUrq4DM/видео.html
That was great Elin! A $13 diode saves a perfectly good Microwave oven that most people would just “dump” and buy another new one ! (I bet all the Microwave manufacturers will REALLY hate you for this ha ha!) thanks buddy 👍👍
9:32 Those caps have a internal 10m ohms resistor. That is why they usually discharge quickly. Still >YOU SHOULD ALWAYS< do the discharge procedure because if the cap still good while the inside resistor opened the cap will not discharge quickly and will zap you to death.
Background fact to the Microwave oven we so take for granted these days: British scientists were developing world leading radar before and during WWII. Its how we managed to defend our islands for so long when we stood alone with our commonwealth friends like Canada, Australia, New Zealand etc. The long wave radar was only suitable for land or limited sea use and impossible in the air and so short wave radar was developed. The British designed the 'Cavity Magnetron Radar' for these uses. However the pressures of war made manufacture slower than was needed. In 1940 and (and again in 1941) Missions were sent to the USA with Canada's involvement, as the ship (RMS EMpress of Canada) docked at Halifax, under the direction of one Henry Tizard. The idea was simple - Give a neutral USA advanced technology and in return they will let us buy their production capacity and win the war. Amongst the technologies given were: The proximity (VT) fuse Self sealing fuel tanks Atomic fission The Jet Engine Gyroscopic Bombsights Advanced Sonar Plastic explosives And of course 'Cavity Magnetron Radar' which the American historian James Phinney Baxter III would later call "the most valuable cargo ever brought to our shores". It re-defined advanced (and mobile) radar and brought significant advantage to Allied air forces especially in the battle against U Boats. Canada had benefit from this as Tizard met Canadian George Laurence who was developing steam power from nuclear fission. The British Government directly funded his research and gave him access to their research as there might be some use after the war. Which there was of course. So something that is now so simple, taken for granted and has had such a beneficial effect on our daily lives started out as a means of advanced warfare and was gifted to the world by a nation fighting for its very survival.
I'd like to point out, the cavity magnetron was invented by the Brits and at the time it required a skilled British machinist three weeks to machine the cavity. An American figured out how to do it with a set of stamped copper plates that were braised together and then it could be quickly produced in huge volume. Then it won the war.
I liked your presentation - excellent!!! Thanks for making a video of your work to help us. I liked your aptitude on fixing and not throwing it away. Great work. I have my OTR microwave, within one year of purchasing it brand new, started blowing fuses just within a few seconds of running. I have not thrown it. My previous one lasted 12 years. This one is almost new, and I am planning to check the status of the capacitor (I know deadly, will remember to discharge it) as well as the thermal fuse.
Mw diode have a big resistance that it cannot be tested directly using a multimeter , you must used a 9v battery to polarised it then connect diode with battery and multimeter in series for testing
I had a Hamilton Beach model P90D23AL. Everything worked, but the mag would not turn on. I did the easy checks first: the mag-circuit (diode, capacitor, fuse, mag filament, connection to transform HV coil). There were no improper shorts or open circuits. The diode tested well. Then I checked the transformer primary for continuity or shorts. No problem. The HV secondary was 150 ohms to the case. No problem! I suspected that the door interlock that controls the mag was faulty. Now, the struggle began. They snapped-in when connected, and I could not remove them with ordinary tools (needle-nose pliers). I concluded that they were not made to be easily removed. I tried to remove the interlock switches with the leads still connected to them. They were held by plastic retainers that I could not pry out of the way. RUclips has several videos on the magnetrons and other big components. What we amateurs need is advice on how to remove those snapped-in connecting lugs. That, to me, is the hard part.
Awesome video!!!! Great explanation and walk through on it's repair!!! I also love the fact that you had me laughing while watching it!!! The victim microwave comment was priceless!!! I'm going to repair mine. Thanks!!!!!
The high voltage Diode used on microwave ovens can not be effectivly tested in this manor due to there very high internal resistance , if you use this method it will "allways" test open in both directions , The High Voltage system in microwave produces absolutly lethal high current high voltage power so one must follow proper service procedures or you can seriously injured or killed you can not take any shortcuts when it comes to protecting yourself , most microwave oven capasitors have a drain resistor "But" one must allways assume cap is charged and discharge it properly accross a resistor, shorting it out can damage it due to the very high current flow ..how to make a discharger ruclips.net/video/pVIV905qby0/видео.html , as spoken about below one must use good 9 volt battery in the diode test process ruclips.net/video/PdwbjNCK-xw/видео.html . allways make sure the mica waveguide cover on the inside of the microware where the microwaves enter the cavity is not damaged by burnt on food a damaged waveguide cover will refect microwave energy back into the magnetron , replace it if it is ..
@Elin Yakov's Rusty Beauties. Hey Elin, our GE microwave is doing the same thing that yours was doing. Before I found your video, I happen to have a bag of microwave popcorn here, so I put that in and tapped the ''Popcorn'' button and it went through the heating cycle and when it beeped the usual 3 times, it read ''Sensor Error''.... So far the only answer I found in a google search was a door switch could be bad, or something else I read said the ''Humidity'' Sensor could be bad but because it sounded just like your microwave, I am going to check the diodes first. Thank you so much for making this video. I'll check out the diode tomorrow....
THANK YOU! Little did I know that ALL microwave ovens look almost EXACTLY the same on the inside AND the wiring is virtually identical. The only difficult issues are the electronics, I'd stay away from fixing them.
A tip to everyone, to discharge a capacitor you just have to put any resistor across the capacitor. Problem solved no sparks, the resistor will drain the capacitor to 0V.
A long flathead screwdriver with a thick plastic handle will discharge the cap too. No guarantees your screwdriver will handle the charge cleanly. At your own risk.
Are all magnetrons standard in power, voltages, watts and ohms, etc., and can be used as replacements in any microwave oven? I'm trying to repair my microwave oven which is just about 2 years old, and the magnetron has stopped working. It's one of those that has a static (hot) plate - not the rotating kind. Can I use a magnetron from a rotating plate microwave oven to repair mine?
Hi fred..ive got a ge microwave thats not heating...when i click start the fan turns on table turns..i hear a click relay but no hear normal humming sound anymore....i checks diode and is ok...i check door limit switches ok...what other part could be the issue?...the hv cap is not bulged on top
Very informative sir, but sir I do have a question how do you replace the cables you have discharged from the capacitor coz you said that you have to be careful when discharging the cables so what about replacing them back there is no problem I can use my free hand it's not dangerous or what coz I am I beginner in these things sir
@@mikeyncali Found a used one on eBay. I think I paid $40 or so. The high voltage diode was just a few dollars (very common component) and they have it both on eBay and Amazon. You dont have to discharge a magnetron, or the transformer. AFAIK the only component in a microwave that can hold a charge is a capacitor, if there is one. If you want to be extra extra safe, just leave it unplugged for 30-60 minutes before. Or you could also short the large capacitor (if there is one) to make sure it is discharged.
Microwave oven doors have microswitches. These microswitches sense if the door is open or closed. They are in part mechanical and will fail. If all else tests functional, the door microswitches may be the culprit.
@ Jose Sanchez. Jose, you do have to be careful. I have herd horror stories about people who did get hurt badly because a capacitor was loaded with energy....
I think you got lucky with the open diode, because testing it with a regular multimeter in the resistance mode will not have enough voltage to bias or forward polarize a high voltage diode. (I got that from the service manual for mine that I found online: “NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3 volts.”) You can check the diode with a 9V battery, the meter and the diode all in series, and then reverse the diode. Full battery voltage both ways: shorted diode; 0V both ways: open diode; 0V or very low one way and something higher (maybe 6V) the other: diode okay. But thanks for the video! (Oh, and the manual also said the capacitor discharges in under 60 sec after the power is off, but still you were wise to short it to the chassis!)
My Oster Microwave starting doing the same thing yesterday with the loud humming type noise and no heat. If the diode is bad on my oven and I replace it how do you know which way to put the diode on being as they are one directional with the current as to avoid having it on backwards. Hoping my oven is only a diode also and not the Magnetron or Cap. I have a voltage meter so I can test the diode. Not sure how to test the Magnetron. The Cap I know how to test. Thanks in advance for any help. Philip Jersey Shore area
A HV diode will not be forwarded biased by the diode setting of a multimeter. You can test them with a 9v battery BUT my microwave failed, making the same sound/not heating & it WAS the diode. It passed tge 9v battery test but neither was it open circuit. It was failing when reverse biased & wasn't actually rectifying at all. $10 later or a new diode & it's all good. My guess is that your diode had the same fault.
The high voltage diode will measure open in both directions with a normal multi meter. Even a good one. To test it properly you can either use a Megger or as per the video link posted by Nabzim further down. I prefer using a Megger. Its quick and easy.
@@devoncole5789 - Only if it has a microwave setting. I have several flukes and they do not have that setting. It's not often a person is going to check a HV microwave diode so most meters don't include that kind of scale on their meters. I was both a technician and an engineer and I have only checked a few on them in my lifetime, but thousands on normal diodes! The 9v battery test is very easy and is fool proof, that is how I check them now.
Well well well. Seems it goods now This morning I just check a microwave which is not power on. I check the 3 switches on the door its good. I check the fuse that's also good. I check the power. That's also is good and it's coming into the microwave. But it's not power on. Finally Loosing hope I say let's check the board power supply. So what I see was really shocked me. 2 lizards completely burn on the power supply board. So I did have some power supply board. And I found 1 the same which has been burn. I change it well its looks fine No blown up fuse or Chock sound. And it's working.
Hi, Thanks for the great video. I have replaced just the diode, it was working good for just 1 day, then again got the sparks and stopped heating. I don't know why the new diode died soon. Do you think the old magnetron damaged the new diode? do I need to replace the magnetron too?
I have the same issue, my microwave is not eating at all... I don't wanna replace it because the it is convectional oven still working. Heating food is just a problem
i just saw this and i have the same sound and im hoping its the same fix as just that diode not sure since the big fuse blew and that didnt fix it and still makes the same loud sound but well see :O
SIR, II HAVE GE MICROWAVE AND AFTER SWITCHING ON IT SHOWS COMPLETE DEAD, NO LIGHT IN FRONT PANEL I HAVE CHECKED ALL PART WITH MULTI METER SETTING ON CONTINUITY MODE AND FOUND TO BE OK. EVEN OPEN MANETRON AND FOUND TO BE OK. DOOR SWITCH, RELAY OK. MAIN CABLE OF MICROWAVE IS ALSO OK. WHAT METHOD SHOULD I FOLLOW SO THAT ELECTRICITY PASSES THROUGH MICROWAVE? THANKS.
Great video but unfortunately when you take a microwave in for repair it costs half of a new one, l just replace even though mine looks perfect it’s 17 years old. Sharp are very good ovens.
John 3:16-21 16 For God so loved the world, that he gave his only begotten Son, that whosoever believeth in him should not perish, but have everlasting life. 17 For God sent not his Son into the world to condemn the world; but that the world through him might be saved. 18 He that believeth on him is not condemned: but he that believeth not is condemned already, because he hath not believed in the name of the only begotten Son of God. 19 And this is the condemnation, that light is come into the world, and men loved darkness rather than light, because their deeds were evil. 20 For every one that doeth evil hateth the light, neither cometh to the light, lest his deeds should be reproved. 21 But he that doeth truth cometh to the light, that his deeds may be made manifest, that they are wrought in God.
You have to stick your finger across the capacitor terminals to discharge it. Hold your man-bun with your left hand while placing your right hand on the capacitor and see what happens.
Sir you made me laugh because your approach and reactions are exactly how I would think-and speak when I’m attempting a repair. Good job and thank you for the tutorial.
Some capacitors have a resistor inside (10Mohms) that safely discharges them in a few seconds.
Also, the high voltage diodes can't be tested with a regular multimeter alone. They need to pass a higher voltage than what the multimeter can offer, anything more than 9V. The multimeter will test the voltage going out of the diode: forward it will drop around 5V, and won't drop anything in reverse.
This is the most helpful video I've seen so far because it is the same problem I am having, loud noise and no heating. You are a resourceful guy!
Agreed... same here!
HV Diode have several diodes in series in order to have a HV rating. A multimeter diode tester is only good for a single junction diode with a forward junction drop below 3v to 4v. Use a 9v battery in series to do a HV diode test.
thanks, i was wondering why my multimeter was not showing a voltage
@@quintinplaza, I knew that was not correct. You can't measure a microwave diode with a multitester without injecting some voltage through it. Nine volts will do.
Testing a high voltage diode is not as simple as using the multimeter's diode test function. It showed open circuit in both directions because the multimeter's voltage is not high enough to overcome the voltage drop of the diode. Here is a video that shows a way to measure it with a regular DMM: ruclips.net/video/1pp4LUrq4DM/видео.html
Great video! Thanks for sharing. Mine makes all the same noise but still heats things up
😂 I practically held my breath while you were working on it
I was following along, and getting ready to fix my microwave. But when he said, this might kill you at 2:20, I backed out. 😂 😂 😂 😂
😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂 yeay !
Lol yeah, I'd rather just spend 70 bucks for a brand new one with a fresh 1 year warranty.
It’s a good video and I’m just going to joke around so don’t get upset.
He doesn’t have all the tools but he’s got all the tools he needed.
That was great Elin! A $13 diode saves a perfectly good Microwave oven that most people would just “dump” and buy another new one ! (I bet all the Microwave manufacturers will REALLY hate you for this ha ha!) thanks buddy 👍👍
9:32 Those caps have a internal 10m ohms resistor. That is why they usually discharge quickly.
Still >YOU SHOULD ALWAYS< do the discharge procedure because if the cap still good while the inside resistor opened the cap will not discharge quickly and will zap you to death.
Background fact to the Microwave oven we so take for granted these days:
British scientists were developing world leading radar before and during WWII. Its how we managed to defend our islands for so long when we stood alone with our commonwealth friends like Canada, Australia, New Zealand etc. The long wave radar was only suitable for land or limited sea use and impossible in the air and so short wave radar was developed. The British designed the 'Cavity Magnetron Radar' for these uses. However the pressures of war made manufacture slower than was needed.
In 1940 and (and again in 1941) Missions were sent to the USA with Canada's involvement, as the ship (RMS EMpress of Canada) docked at Halifax, under the direction of one Henry Tizard. The idea was simple - Give a neutral USA advanced technology and in return they will let us buy their production capacity and win the war. Amongst the technologies given were:
The proximity (VT) fuse
Self sealing fuel tanks
Atomic fission
The Jet Engine
Gyroscopic Bombsights
Advanced Sonar
Plastic explosives
And of course 'Cavity Magnetron Radar' which the American historian James Phinney Baxter III would later call "the most valuable cargo ever brought to our shores". It re-defined advanced (and mobile) radar and brought significant advantage to Allied air forces especially in the battle against U Boats.
Canada had benefit from this as Tizard met Canadian George Laurence who was developing steam power from nuclear fission. The British Government directly funded his research and gave him access to their research as there might be some use after the war. Which there was of course.
So something that is now so simple, taken for granted and has had such a beneficial effect on our daily lives started out as a means of advanced warfare and was gifted to the world by a nation fighting for its very survival.
1chish Wow! That was a very interesting piece if history! Thank you for the lesson!
@@RustyBeauties oh I hope it was nothing more than an interesting footnote to show how history develops ...
I'd like to point out, the cavity magnetron was invented by the Brits and at the time it required a skilled British machinist three weeks to machine the cavity. An American figured out how to do it with a set of stamped copper plates that were braised together and then it could be quickly produced in huge volume. Then it won the war.
@@xenuburger7924 Not quite how it happened but whatever ...
I liked your presentation - excellent!!! Thanks for making a video of your work to help us. I liked your aptitude on fixing and not throwing it away. Great work. I have my OTR microwave, within one year of purchasing it brand new, started blowing fuses just within a few seconds of running. I have not thrown it. My previous one lasted 12 years. This one is almost new, and I am planning to check the status of the capacitor (I know deadly, will remember to discharge it) as well as the thermal fuse.
Mw diode have a big resistance that it cannot be tested directly using a multimeter , you must used a 9v battery to polarised it then connect diode with battery and multimeter in series for testing
Cheftush did a great job building this, you can’t see any weld lines!
Great door gaps too :)
I had a Hamilton Beach model P90D23AL. Everything worked, but the mag would not turn on. I did the easy checks first: the mag-circuit (diode, capacitor, fuse, mag filament, connection to transform HV coil). There were no improper shorts or open circuits. The diode tested well. Then I checked the transformer primary for continuity or shorts. No problem. The HV secondary was 150 ohms to the case. No problem!
I suspected that the door interlock that controls the mag was faulty. Now, the struggle began. They snapped-in when connected, and I could not remove them with ordinary tools (needle-nose pliers). I concluded that they were not made to be easily removed. I tried to remove the interlock switches with the leads still connected to them. They were held by plastic retainers that I could not pry out of the way.
RUclips has several videos on the magnetrons and other big components. What we amateurs need is advice on how to remove those snapped-in connecting lugs. That, to me, is the hard part.
Awesome video!!!! Great explanation and walk through on it's repair!!! I also love the fact that you had me laughing while watching it!!! The victim microwave comment was priceless!!! I'm going to repair mine. Thanks!!!!!
The high voltage Diode used on microwave ovens can not be effectivly tested in this manor due to there very high internal resistance , if you use this method it will "allways" test open in both directions , The High Voltage system in microwave produces absolutly lethal high current high voltage power so one must follow proper service procedures or you can seriously injured or killed you can not take any shortcuts when it comes to protecting yourself , most microwave oven capasitors have a drain resistor "But" one must allways assume cap is charged and discharge it properly accross a resistor, shorting it out can damage it due to the very high current flow ..how to make a discharger ruclips.net/video/pVIV905qby0/видео.html , as spoken about below one must use good 9 volt battery in the diode test process ruclips.net/video/PdwbjNCK-xw/видео.html . allways make sure the mica waveguide cover on the inside of the microware where the microwaves enter the cavity is not damaged by burnt on food a damaged waveguide cover will refect microwave energy back into the magnetron , replace it if it is ..
The capacitor has a 10 meg ohm resistor across the capacitor terminals internally for safety. That is why it did not spark.
@Elin Yakov's Rusty Beauties. Hey Elin, our GE microwave is doing the same thing that yours was doing. Before I found your video, I happen to have a bag of microwave popcorn here, so I put that in and tapped the ''Popcorn'' button and it went through the heating cycle and when it beeped the usual 3 times, it read ''Sensor Error''.... So far the only answer I found in a google search was a door switch could be bad, or something else I read said the ''Humidity'' Sensor could be bad but because it sounded just like your microwave, I am going to check the diodes first.
Thank you so much for making this video. I'll check out the diode tomorrow....
Great job you have a great sense of humor I missed the swaring. LOL
I have one to fix with the same symptoms.
My microwave has the same sound. I already bought a new one, but I will try and fix the old one the same way. Thank you for sharing.
Ok so did you fix the other microwave m????
LOL. I really like Russians for their gutsy moves and attitudes, get-it-done ethic to see it through.
Wow! I’m so happy you fixed it. I felt bad after it crapped out on you after 1 use! Good for you! 😎
I told you I am not giving up on it that easy :) Thanks again!
Fancy stitching your mate up with a none working microwave tut tut, just joking you knew Elin was a wizard and would make a video of it lol
THANK YOU! Little did I know that ALL microwave ovens look almost EXACTLY the same on the inside AND the wiring is virtually identical.
The only difficult issues are the electronics, I'd stay away from fixing them.
A tip to everyone, to discharge a capacitor you just have to put any resistor across the capacitor. Problem solved no sparks, the resistor will drain the capacitor to 0V.
Is it enough to produce ventricular fibrillation? I think so.
These caps also have a built in resistor to discharge them
A long flathead screwdriver with a thick plastic handle will discharge the cap too. No guarantees your screwdriver will handle the charge cleanly. At your own risk.
Thanks, that's exactly what our microwave is doing; loud noise, no heat. I'll try the diode.
Are all magnetrons standard in power, voltages, watts and ohms, etc., and can be used as replacements in any microwave oven?
I'm trying to repair my microwave oven which is just about 2 years old, and the magnetron has stopped working. It's one of those that has a static (hot) plate - not the rotating kind. Can I use a magnetron from a rotating plate microwave oven to repair mine?
Hi fred..ive got a ge microwave thats not heating...when i click start the fan turns on table turns..i hear a click relay but no hear normal humming sound anymore....i checks diode and is ok...i check door limit switches ok...what other part could be the issue?...the hv cap is not bulged on top
Very informative sir, but sir I do have a question how do you replace the cables you have discharged from the capacitor coz you said that you have to be careful when discharging the cables so what about replacing them back there is no problem I can use my free hand it's not dangerous or what coz I am I beginner in these things sir
That's what we call a "zero sum" game....one fixed microwave, one sacrificed microwave....net result is the same as before you started ;-)
Just fixed a Samsung above range microwave. It was the magnetron and also the diode I think. Replaced both and now it works.
How much that run you I am about todo the same thing and did you have to discharge it at all?? TIA
@@mikeyncali Found a used one on eBay. I think I paid $40 or so. The high voltage diode was just a few dollars (very common component) and they have it both on eBay and Amazon.
You dont have to discharge a magnetron, or the transformer. AFAIK the only component in a microwave that can hold a charge is a capacitor, if there is one. If you want to be extra extra safe, just leave it unplugged for 30-60 minutes before. Or you could also short the large capacitor (if there is one) to make sure it is discharged.
The big screwdriver seems to be anodized, and won;t work well to short the capacitor! Just use the pliers to connect the terminals.
one of the best explained video's I have seen thank you, you are credit to you tube I have also subscribed
Please suggest the price of fixing too
Microwave oven doors have microswitches. These microswitches sense if the door is open or closed. They are in part mechanical and will fail. If all else tests functional, the door microswitches may be the culprit.
Tried this and shocked the hell out of myself got the microwave working tho
Did you handle it ? I still afraid of electricity after being shocked by this 300 bucks piece of shit
@ Jose Sanchez. Jose, you do have to be careful. I have herd horror stories about people who did get hurt badly because a capacitor was loaded with energy....
I think you got lucky with the open diode, because testing it with a regular multimeter in the resistance mode will not have enough voltage to bias or forward polarize a high voltage diode. (I got that from the service manual for mine that I found online: “NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3 volts.”) You can check the diode with a 9V battery, the meter and the diode all in series, and then reverse the diode. Full battery voltage both ways: shorted diode; 0V both ways: open diode; 0V or very low one way and something higher (maybe 6V) the other: diode okay. But thanks for the video!
(Oh, and the manual also said the capacitor discharges in under 60 sec after the power is off, but still you were wise to short it to the chassis!)
Worth the shock I guess 😂
🤞🤬⚡️ 🫷👀☝️
He could have used the pliers to short out the capacitor.
Good job! Thanks for sharing your experience. I now have better idea of what I have to do.
You are THE MAN. Leave some women for the rest of us! :) - Paul
Use a rubber handled needlenose pliers to discharge the capacitor.
Good job ! Thank you for your problem-solving approach and down-to-earth explanations.
My Oster Microwave starting doing the same thing yesterday with the loud humming type noise and no heat.
If the diode is bad on my oven and I replace it how do you know which way to put the diode on being as they are one directional with the current as to avoid having it on backwards.
Hoping my oven is only a diode also and not the Magnetron or Cap. I have a voltage meter so I can test the diode. Not sure how to test the Magnetron. The Cap I know how to test. Thanks in advance for any help.
Philip
Jersey Shore area
The cathode has a silver ring on its body. This goes to ground. The other terminal (anode) goes to the capacitor.
A HV diode will not be forwarded biased by the diode setting of a multimeter. You can test them with a 9v battery BUT my microwave failed, making the same sound/not heating & it WAS the diode. It passed tge 9v battery test but neither was it open circuit. It was failing when reverse biased & wasn't actually rectifying at all. $10 later or a new diode & it's all good. My guess is that your diode had the same fault.
You are a live saver ❤ God bless you 🎉
Thanks bro this video was very helpful..
The high voltage diode will measure open in both directions with a normal multi meter. Even a good one. To test it properly you can either use a Megger or as per the video link posted by Nabzim further down. I prefer using a Megger. Its quick and easy.
And yet, it fixed the microwave ...
I got a fluke I bet checks them just fine
@@devoncole5789 - Only if it has a microwave setting. I have several flukes and they do not have that setting. It's not often a person is going to check a HV microwave diode so most meters don't include that kind of scale on their meters. I was both a technician and an engineer and I have only checked a few on them in my lifetime, but thousands on normal diodes! The 9v battery test is very easy and is fool proof, that is how I check them now.
Well well well.
Seems it goods now
This morning I just check a microwave which is not power on.
I check the 3 switches on the door its good.
I check the fuse that's also good.
I check the power. That's also is good and it's coming into the microwave.
But it's not power on.
Finally Loosing hope I say let's check the board power supply.
So what I see was really shocked me.
2 lizards completely burn on the power supply board.
So I did have some power supply board.
And I found 1 the same which has been burn.
I change it well its looks fine
No blown up fuse or Chock sound.
And it's working.
Hi, Thanks for the great video. I have replaced just the diode, it was working good for just 1 day, then again got the sparks and stopped heating. I don't know why the new diode died soon. Do you think the old magnetron damaged the new diode? do I need to replace the magnetron too?
Personally l would just replace the entire unit, once these things start malfunctioning it’s an ongoing problem. 🤷🏼♀️
Where can I buy the diode & what type of diode? Thank you.
Thanks! Great video. However, my best choice would be to get a new diode, indeed!
Good video and funny , I have the same problem Thank you that was easy to fix my self👌👌👌
I have the same issue, my microwave is not eating at all...
I don't wanna replace it because the it is convectional oven still working.
Heating food is just a problem
Thank you will try that tomorrow mine is doing the same thing
thank you for sharing. i have the same problem. i'm going to give it i try,
i just saw this and i have the same sound and im hoping its the same fix as just that diode not sure since the big fuse blew and that didnt fix it and still makes the same loud sound but well see :O
Chef Tush called, He wants his machine back.
SIR, II HAVE GE MICROWAVE AND AFTER SWITCHING ON IT SHOWS COMPLETE DEAD, NO LIGHT IN FRONT PANEL I HAVE CHECKED ALL PART WITH MULTI METER SETTING ON CONTINUITY MODE AND FOUND TO BE OK. EVEN OPEN MANETRON AND FOUND TO BE OK. DOOR SWITCH, RELAY OK. MAIN CABLE OF MICROWAVE IS ALSO OK. WHAT METHOD SHOULD I FOLLOW SO THAT ELECTRICITY PASSES THROUGH MICROWAVE? THANKS.
@sultan Merchant: There should be a fuse close to where the power cord attaches.
Thanks for your Video, Hope this Will HElp me Fix Mine! God Bless!
My symptoms are the same, wife is thinking whirlpool deals for whole new unit. If it's the diode we trade it in and somebody gets a good MWV for $10.
Can I use wire if I don't have the fuse
Nope. Won't work.
Great video but unfortunately when you take a microwave in for repair it costs half of a new one, l just replace even though mine looks perfect it’s 17 years old. Sharp are very good ovens.
Thanks. Good and helpful.
A "Popping Noise"? Whoa ! Backed Me Off But Good ! That's Above My Pay Grade ! I Need An Expert !
Thank you very much.
Great explanations!!!
Loved the cooking glove😂
There's also Fuses in there also
Thanks. Fixed mine too.
Great video man, entertaining also!
just pull out the diode, then the cap is disconnected, just dont touch the terminals of the cap, which is most unlikely
This is not the method to test HV diode. You need a 9v battery and test for forward bias voltage drop.
What if microwave has no diode
Thank you bro
What color are you going to paint it ?
Cheftush White :)
I just got one and it has tons if noise but doesn't heat up shit, any solutions?
My microwave cost $500 bucks, I want to repair mine that quit heating but powers, works and sounds normal with no heating.
Teach me how to convert 110 to 220 blender
you cant test microwave diode with DVM you need 9v battery
i love this guy
How to magnetron
Wrong, the multimeter will not check these diodes.
not how you test HV diodes bro,even a brand new diode would still give same results if tested that way,rather use a 9v battery
DIOS CAN MAKE MICRO NOT HEATING
Thanks man!
Very Good!... #92 ✝ {6-5-2022}
I don’t see you what you fix
naaaaice !! 👍🏻👍🏻
🤣🤣🤣🤣that slow motion turn to the other microwave for parts
DRcongo Joseph thank you brother ant your are sooooo funny
8:44 Orr ohh! lol
Sooo…..just get a new one…..
Multimeter of no value testing that hv diode.
well, if youve unplugged it, no need to discharge
Blender repair
Hi super maestro on spjegat
You look like Roman Reigns
John 3:16-21
16 For God so loved the world, that he gave his only begotten Son, that whosoever believeth in him should not perish, but have everlasting life. 17 For God sent not his Son into the world to condemn the world; but that the world through him might be saved. 18 He that believeth on him is not condemned: but he that believeth not is condemned already, because he hath not believed in the name of the only begotten Son of God. 19 And this is the condemnation, that light is come into the world, and men loved darkness rather than light, because their deeds were evil. 20 For every one that doeth evil hateth the light, neither cometh to the light, lest his deeds should be reproved. 21 But he that doeth truth cometh to the light, that his deeds may be made manifest, that they are wrought in God.
Zegbolor
You have to stick your finger across the capacitor terminals to discharge it. Hold your man-bun with your left hand while placing your right hand on the capacitor and see what happens.
Man it’s not funny at all. This shit can kill people