Tacoma LED License Plate Lights - Installation Instructions
HTML-код
- Опубликовано: 4 авг 2024
- In this video I install a set of LASFIT LED license plate lights on my 3rd Generation Toyota Tacoma.
Get License Plate Lights on Amazon:
amzn.to/2zpcTPH
Fog Lights Install:
• LED Fog Lights for the...
4S Fog Lights: amzn.to/2BPvDWz
Low Beams Install:
• New LED headlights on ...
Low Beam Bulbs: amzn.to/375ZvgT
License Plate Lights Install:
• Tacoma LED License Pla...
License Lights:
amzn.to/2zpcTPH
#ToyotaTacoma #TacomaLEDs #3rdGenTacoma #Tacoma #ytmikec Авто/Мото
love the smokey plates, thanks for the tips.
Thanks! Very clear and helpful instructions.
I have a 2021 Tacoma and I followed your directions but the space was too tight for my hands. I noticed that the lens wobbles in place from the front so I encourage it out from the sides using a wide blade stubby screwdriver. Then I changed the bulb without an issue and popped the lens assembly in place. This might help those who can't wedge their hands in this tight space.
Thanks this was very helpful,Love my Tacoma.Go Smokie.
Nice video....ez upgrade...one of the 1st I did ..
Well Mike I installed LEDs in my license plate lights to but I couldn't get my hand up in there as easy as you could with a lot of swearing cuts and scrapes by the time I get done it looked like I went a few rounds with Freddy Krueger LOL I do know there's a video out there of someone is taking out the license plate light from the front anyways great video great instructions keep them coming looking forward to the next one you and your family be safe
Sorry your install didn't go as easy!
I just changed mine out and I can relate with looking like I went a few rounds with Freddy!
I have small hands in my opinion , but maybe not , since I just spent 15 minutes on one and just can get the bulb out. And I was laying down , I can't even imagine doing it sitting up. I'm sure my 2019 Tacoma Off Road isn't any different. Guess I will try it sitting up after my knuckles heal.
I had a terrible time trying to get mine done, my hands aren’t oversized by no means, but my fingers are kind of short! I found the video of the guy who took the light out of the bumper, I’m going to try that tomorrow
@@harry39196 good luck , I just don't have nimble fingers and my wrists are not flexible , so I struggle with stuff like this. I did finally get them in but the one side is not turned as far as it can go. So far they are both in and not hanging down.
Some people insert splungers and pull the whole square lens out from the front side. I'm a small-hands guy, and I wasn't able get both my bulbs out with the twist-pull from the bottom. Ended up in the end doing both from the splunge, pull method for the whole assembly.
Thanks
Great video bro, tnx
Looks awesome
This was not easy for me to access at all. Maybe my hands are too big. My fingers got torn up trying to get it in and out
I want to put LED DRL on my 21 SR5 but I think their the same bulbs as the turn signals. Any knowledge of this? Any suggestions?
I don't believe these changed for the 2020 refresh but I'm not certain
Just showed my husband up with your video! I have smaller hands! Thanks
What if the bulbs don’t fit it? Is there a fuse or anything? 2007 pre runner
Smallest hands ever
Do you know which fuse is reverse
Hey mike, where did you get you TRD pro grill from?
Cali Raised. Here's a link to the install video if you're curious: ruclips.net/video/TUHNovLYFVo/видео.html
Awesome thanks, I guess all I had to do was type in Mike C TRD pro grill and the video popped right up!
mike, like that but concerned with big hands how easy is it to do?
I felt there was plenty of space but there's another comment from someone that said the install was a lot harder for them. Hard to say!
I’ve been trying, don’t think I have overly big hands and just can’t get in there and get a grip
It's extremely difficult with big hands! Pay close attention to how the blub housing aligns with the fixture. This will save you some time in the pinched position!
My hands are not overly big, but my fingers must be short! I finally gave up until I watched the video tonight of the guy who went on the outside of the bumper and took out the whole assembly, which looked like it was a lot easier. I’m going to try that tomorrow
Problem with the LED bulbs, at least the ones I installed, is that they are so bright that they overwhelm the image in the back up camera.
Hmmm , I didn't think of that.
And... if they are not DOT certified... may be illegal in some states. (Not looking at you, Virginia!)
There is an adapter you can get to disable the license plate lights while in reverse
Crap. I bought mine off of Yotaverse but haven't installed them yet. Now I'm afraid to.
Does this work on 2021 models? Amazon link says it wouldn’t, but not sure if that’s accurate.
Yes, these shouldn't haven't changed any for 2021.
You must have small hands
Quick and easy? Only for 12 year olds and typist hands
I literally can't get my hands in there enough to turn the housing. Anybody have any tips?
I just watched another video that the guy took the light out of the bumper from the outside. He just pooped the lense off and was able to access the bulb so easily. My hands are way too big and my fingers way too short to go under. Hope that helps
@@harry39196 do you have a link to the video or who made it? I can’t get this bulb unscrewed lol
Don’t need to do all that to change your bulb.
thanks for the vid
but
i'll pass on the led
waaaay too bright.
You look like stradman
He looks like me
Why would you want people to see your plates? Lol.
👍😀😁🇨🇺👊
Good information here, but you do have to have the hands of a 10 year old girl...