I was able, incidentally, to resolve my problem with NCS Expert not running when INPA did run. So for the benefit of others who might encounter a similar issue, I did so simply by soldering together pins 7 and 8 on the OBD connector (top left two pins on the wide edge as you look at the socket). That was the simple fix which got NCS Expert running perfectly on an '02 E46. I have the white circuit board on my OBD connector and understand that the green circuit board is preferred, with two K-Line leads, thus presumably not requiring the soldering. But the soldering together of the two pins works. For those unfamiliar with soldering, use a short, half-inch length of wire to solder the pins together after removing the four screws on the socket and gently prying apart the two plastic shell halves of the socket. Gently unplug the small socket connector inside from the top of the circuit board to avoid touching that inadvertently with the iron and then plug it back in when done before putting the shell halves back together. "Tin" each exposed end of the half-inch length of small-gauge wire, that is run a little solder over the exposed ends before soldering to the pins, to make them easier to solder to the pins. Then all you need to do is momentarily touch the tinned ends to each pin while soldering for just a couple of seconds or so. That way you won't run the risk of de-soldering the pins or burning any components with excessive heat. I had already changed out the USB driver on Windows XP in the Virtual Machine, which was loaded by default during installation, to the most recent version at the "Virtual COM Port Drivers" website, FTDI drivers. Look for the most recent XP driver or the most recent Windows driver and either will work. That had been my first connectivity issue, which prevented even INPA from working. Install manually in the Device Manager of the Virtual Machine XP version, not in the host Device Manager. (I am running Windows 10 in my host machine.) Thanks again for these excellent videos. They saved my day after two and a half years of looking for precise instructions on recoding the computer after the transmission swap to eliminate the error code looking for an automatic computer module no longer present, hence preventing smog inspection, even though obviously having nothing to do with emissions ...
I just wrestled my way through numerous software configurations and after seeing your comment here, finally remembered from a long time ago when I was setting up bmwlogger with a k-line adapter on an E36, that people were mentioning bridging those pins. I didn't have to do that then, but this time I was starting to suspect the hardware and I'll be damned if shorting 7 to 8 didn't fix my "VIN is faulty" error that I have been trying to get past for like three days. Thank God I saw your comment! On a side note, I purchased my k+d can adapter a year or more ago and just had it on hand, so I'm not sure what is going on with ones produced now, but my PCB has a green solder mask, not a white one, but it required the jumper just the same. I don't usually read comments but thank you so much for taking the time to note this.
Just a VERY important tip, make SURE you get the cable with the GREEN circuit board, I went through trial and error buy buying one with a WHITE circuit board that does NOT work. I eventually got the one with the GREEN PCB and it works 100%
This is a superb series of video. I am also trying to recode my E46 to a manual from an automatic after having performed the swap and this is the first series of videos which provides the sequence in clearly understandable terms. I have been looking for two and a half years since I completed the swap. Thanks... But I have a problem. I got the software working properly and INPA links to the car and reads, etc. But NCS Expert, while it loads expert mode properly, returns a COAPI 2020, no response from ECU, error code whenever I hit any of the modules under ZCS/FA f. ECU after entering E46, i.e. AKMB or ALSZ. I was having a problem initially with INPA not addressing the car, until I changed out the USB driver to 2.08.24 on the VM XP 32 bit device manager from an earlier driver which came with the D-Can + K OBD connector. So, now INPA works, but not NCS Expert. I am set up in the XP Home Edition on the Virtual Machine in Windows 10 64 bit original host environment. I have a feeling it is still some connectivity issue with the USB driver in the Virtual Machine for XP. The USB driver, incidentally, is configured to COM1 with a latency of 1. Has anyone else encountered this issue? It seems odd that INPA works but not NCS.
This is the best instructional with NCS expert INPA installation. Honestly information is all over the place and sometimes I've spent time I cant get back reading forums only to conclude that it doesnt show how to do it or its wrong and not working. Thank you sir. I have one question though on a subject Im having even harder time finding. I plug it in and INPA recognizes I have the cable plugged in. When I go into NCS Expert it recognizes it as well but when I try to load the modules and read VO it brings up "Following feature is invalid for FA: #1207" and I get it to load the codes but I cant change them. Ive read in various forums that I have to update the Daten files and I finally found a download page with V60.1 I think...Well now I have no clue how to update them. Ive tried manually copying them into what I thought were their respective folders but it actually made the program work less and gave me more errors. I had to reinstall your method again as I lost where I went wrong. Anyway you can help guide me what forum (theres so many) you may have learned to update, etc? I have a mac running Windows XP 32bit virtual machine. Trying to code on a 2008 335XI (has JB4, this couldnt be an issue could it?) . I should try it on my e46, maybe its my car, or maybe my cable...
Sir, You rock. Yeehah! Following your astonishingly clear instructions I'm up and running on a Mac Air with Windows XP, using virtual framework Parallels Desktop 7, on Mac OS10.6.
Btw This is NOT a criticism but the very first step in the pdf instructions seemed to be missed out - Updating the System Variables Path. A note for anyone else doing this and having errors after running the Install EDIABAS etc (Instprog.exe at 8:52). At the end when you hit the Exit button (9:25 in the vid) it can take a while for it to close. Just wait for it to close itself. It is definitely working in the background and the first couple of times I force-closed the window which I think was the cause of subsequent errors. The more of the modules you 'Check' to install, the longer it seems to take.
Hoping you can help here. Bought one of these inpa cable and cd packages off Amazon. My computer wont run it because it says it has a malware virus inside, any idea?
Hello 50's KID... perhaps you've some instructions pointed at disabling/removing The "ews" features from the DME...My same vehicle is the 2004 E60 545i. produced in may 2004. Inpa error codes are 2737 & 27A4... Perhaps there a preferred way to contact you? (youtube doesn't allow?)
I ran INPA 5.0.8 on every single Windows version after XP (Vista, 7, 8 and 10) with no problem. So before messing around with a virtual machine for no reason (unless you dont want that stuff on your physical computer) you should get this newer version. 6.4.3 is only essential if you want to diagnose older BMW without OBD. But then you also need another diagnostic cable.
Great tutorial. But, gosh darn it, I copied the wrong NCSEXPER file in the very last step. I copied NCSPRINT by mistake. Now it's all in German. Lol. I got too excited for the end, because all my previous attempts to install with the CD that came with my cable kept throwing errors to paths not found. This tutorial is great, well articulated, and everything works like how it works in the video... Just be patient
Hi 50skid.I have a bmw x5 e53 2001.. 2 weeks ago on my dash apear transmission failsafe when drving.. And need press pedal gas to deep to keep driving because few like stop its to hard to make runing.. But if turn off and turn on again locks like no normal.. Runs good and transmission works good again.. This happen sometimes when stop on ligth for a second.. Bring to mecanic but dont' find anything.. Can you tell me what can do.. Thanks..
Hi bro, I have a used BMW, F20 110i year 2012, imported from Japan...FM radio is set to Japan frequency, I do not get local FM channels, can I change the FM frequency to my local country stations through INPA/NCS Expert? Kindly provide me a link or a clue where to start? Thanks
Hey boss. I am planning to do coding on 2005 bmw 325i. Is this cable works on it ?. I looked some comments they said this cable doesn't function proper because pins . It should be 7 pins. Is it true. If yes then please advise.
hi 50 kids i already set up like your instructions but when i plugged it to my car(e90 320i) the inpa not recognise my ignition only battery on and ignition not on, do you know why?hope you can help me out this is my last step,thanks
What settings are you using for the virtual machine? I"m running windows 10 and when trying to start a virtual xp machine, my computer reboots as soon as I start up the VM. Thanks
hi, need some help. i have it installed, v5.0.0 on my e46 INPA can read the digital and analogue values, it can read in detail the DSC fault codes, but wont read the engine codes in detail. when i select s54 engine it says 'versions do not match. Malfunction possible' Any help would be appreciated (Windows XP)
Hi mate. As good as this programme is.. Could you tell me your views on the 'Carly for BMW' app? I've recently bought it, plus some of the addons, but still using my own obd2 wifi adapter instead of their £50 version, and for what it does I think it's great although a lot of functions aren't that clear. I'd like to hear what your thoughts are on this app if you've used it, or if not, could you do a short video on it as you explain things a lot more clearly than your average instructions. Daz from the UK. E61 530d 2007
I think there are better tools for the money, in this case you are paying a useful app to use with your phone, but I think that for the price you could use (much) better tools to use with your laptop.
Nice car Daz! Exactly the same as mine over here in NZ. The Carly is very good for simple reading and diagnostics but beyond the basic updates like battery registration and changing and fault code resets it doesn't have a patch on the depth of what you can do with this software and a $15 cable. And every time you want to do anything functional in the App it seems you make a 5, 10, 15 euro payment. I understand that their pro version of the App and coding may also now be restricted to using their own Wifi Adapter, the price of which seems to keep going up.
Hey, can you maybe install the cable again. I have the same installation CD and the same cable. Again, if you have spare time! I really have trouble installing my cable. Thank you!
When you register your account do you use bimmer as your password at that time? I am only asking because when I went to register they asked for your full name, email and password. Just wondering if I should use bimmer as my password.
I've got everything installed and working properly but cant seem to remove codes from my E64 so i'm guessing it doesn't support my 650i Convertible? What are your thoughts on this and let me know if there's a fix. I've also got all the latest updates into INPA as of today thanks.
Hey 50sKid - thanks for putting up this fantastic Video. Do I absolutely have to use COM1 for the serial port? I have COM1 currently "in use" so I opted to use COM2: is this going to be an issue?
Thank you so much, gonna get the PC going when I get home I have an 03 540iT, got a 97 540i6spd because the more pedals there are in a wagon, the cooler it is I'm gonna consult the forums for post facelift auto to manual coding because that link is dead, but nbd
im very new and 50's kid has helped me do tremendous things with my bmw that i never would have dreamed of doing, the vids always give me confidence and always work 100 percent....but the one thing i would like to know is WHAT CABLE DO I BUY? i bought an older laptop with windows xp followed these instructions and it worked perfectly, but i need a cable with a 16 pin to serial port (since this laptop has one) that will also allow me to use my 16 to 20 pin adapter for my 323i. im at a loss which cable i am supposed to buy. 50;s kid please help!
Another great video from you! Have you thought about to make a video about installing BMW-TIS ? It's also lister at the 4shared link in the comments. I'm sure a lot of people would be interested and appreciate it.
Can you help me out? I have a 2006 E46 M3 SMG. I bought software and a cable on EBay but discovered that my BMW model was not included. Could you point me to some where I can get the complete software package that will work on my M3? I’ve looked at so many packages I’m cross eyed and confused.
Do these things work with WIN 10? I see that your video is still using Windows XP. Ok you just answered my question. So, what does a person do if they don't have obsolete hardware and software?
Hi so I’m trying this out in sept 2020 and all links even 4shared links are broken, any way you can email me the download links ? Or maybe I can pay you to mail me a USB w the programs ? Thank you
Hello my name is angel I have a m73tu swapped e39touring and I have an issue that I can’t seem to find anyone to help me with. I have a laptop with bmw softwares that I bought off eBay a while back and I used to be able to switch between OBD2 and ADS to connect to my cars but something happened while a tuner was remote tuning my brothers tdi through team viewer and I think he might have moved some settings but now my computer only communicates via ADS and I need it to be able to communicate via obd so I can use sss progman to code the dsc module in my e39 any help would be greatly appreciated thank you✌🏽
I need your help bro i installed it on my laptop Microsoft XP and inpa and othet programs downloaded but when i open everything shows except a few icons dont like F1 F2 AND F10 show and the others are missing. Am i missing files
are you still active.... need help please. Mikes tools is total BS. Errors IFH0018 = OMITEC problems over obd,, 0009 and 0004. like i said that software is total jank. I need this 3.01. that one was perfect from day 1. cannot find it anymore...
wow , why cant it be a click to install and be done.... wow . also I see people saying use a spare laptop , is there a reason why I cant use my main laptop ?
Thank you for such a great tutorial, however, didn't work with my '11 328i e90. Didn't work with Windows 7 and I tried it on an XP laptop. After successfully installing it on XP, INPA worked flawlessly, however, NCSexpert didn't. The error code I was getting is "Following feature is invalid for FA: #0910". Any help would be appreciated!
Good morning, first of all thank you for the good work, your videos have helped a lot, but I have a problem I am not able to connect my E46 in the NCS EXPERT of a VIN number error, at INPA I am able to enter. With my E60, it works well with both INPA and NCS EXPERT.
Hi 50s kid.thanx.I have winkfp in german and version is 4.5.1.anyway to change the language to english or install just the winkfp to a english version.dont want to undo or mess everything else.
look through the files in the directory for the one with the german phrases you see when you use the program, then search the msg boards for the english version of that file.
When I got to 9:24 a pop up came up that some PATH is not found? Link to the pop up image here: i.imgur.com/fL0ZAcp.jpg Any ideas what went wrong? I am installing on Win XP Pro 32 Bit but I don't have a cable yet so I was doing it all on the laptop from where the point where you download and install, I skipped the cable and driver bit. Is that why it went wrong or is it something else?
I was able, incidentally, to resolve my problem with NCS Expert not running when INPA did run. So for the benefit of others who might encounter a similar issue, I did so simply by soldering together pins 7 and 8 on the OBD connector (top left two pins on the wide edge as you look at the socket). That was the simple fix which got NCS Expert running perfectly on an '02 E46. I have the white circuit board on my OBD connector and understand that the green circuit board is preferred, with two K-Line leads, thus presumably not requiring the soldering. But the soldering together of the two pins works.
For those unfamiliar with soldering, use a short, half-inch length of wire to solder the pins together after removing the four screws on the socket and gently prying apart the two plastic shell halves of the socket. Gently unplug the small socket connector inside from the top of the circuit board to avoid touching that inadvertently with the iron and then plug it back in when done before putting the shell halves back together. "Tin" each exposed end of the half-inch length of small-gauge wire, that is run a little solder over the exposed ends before soldering to the pins, to make them easier to solder to the pins. Then all you need to do is momentarily touch the tinned ends to each pin while soldering for just a couple of seconds or so. That way you won't run the risk of de-soldering the pins or burning any components with excessive heat.
I had already changed out the USB driver on Windows XP in the Virtual Machine, which was loaded by default during installation, to the most recent version at the "Virtual COM Port Drivers" website, FTDI drivers. Look for the most recent XP driver or the most recent Windows driver and either will work. That had been my first connectivity issue, which prevented even INPA from working. Install manually in the Device Manager of the Virtual Machine XP version, not in the host Device Manager. (I am running Windows 10 in my host machine.)
Thanks again for these excellent videos. They saved my day after two and a half years of looking for precise instructions on recoding the computer after the transmission swap to eliminate the error code looking for an automatic computer module no longer present, hence preventing smog inspection, even though obviously having nothing to do with emissions ...
I just wrestled my way through numerous software configurations and after seeing your comment here, finally remembered from a long time ago when I was setting up bmwlogger with a k-line adapter on an E36, that people were mentioning bridging those pins. I didn't have to do that then, but this time I was starting to suspect the hardware and I'll be damned if shorting 7 to 8 didn't fix my "VIN is faulty" error that I have been trying to get past for like three days. Thank God I saw your comment! On a side note, I purchased my k+d can adapter a year or more ago and just had it on hand, so I'm not sure what is going on with ones produced now, but my PCB has a green solder mask, not a white one, but it required the jumper just the same. I don't usually read comments but thank you so much for taking the time to note this.
Just a VERY important tip, make SURE you get the cable with the GREEN circuit board, I went through trial and error buy buying one with a WHITE circuit board that does NOT work. I eventually got the one with the GREEN PCB and it works 100%
This is a superb series of video. I am also trying to recode my E46 to a manual from an automatic after having performed the swap and this is the first series of videos which provides the sequence in clearly understandable terms. I have been looking for two and a half years since I completed the swap. Thanks... But I have a problem. I got the software working properly and INPA links to the car and reads, etc. But NCS Expert, while it loads expert mode properly, returns a COAPI 2020, no response from ECU, error code whenever I hit any of the modules under ZCS/FA f. ECU after entering E46, i.e. AKMB or ALSZ. I was having a problem initially with INPA not addressing the car, until I changed out the USB driver to 2.08.24 on the VM XP 32 bit device manager from an earlier driver which came with the D-Can + K OBD connector. So, now INPA works, but not NCS Expert. I am set up in the XP Home Edition on the Virtual Machine in Windows 10 64 bit original host environment. I have a feeling it is still some connectivity issue with the USB driver in the Virtual Machine for XP. The USB driver, incidentally, is configured to COM1 with a latency of 1. Has anyone else encountered this issue? It seems odd that INPA works but not NCS.
the link 4 shared is gone plz re upload thanksyou
Hi, the link at 4shared is not valid. Can you upload again and reply my question with the new link? Thank you for all
virtualbox+ pirate bay xp cd, works like a charm on windows 10
Thanks, looking forward to your "how to use the inpa and ncs expert" video.
This is the best instructional with NCS expert INPA installation. Honestly information is all over the place and sometimes I've spent time I cant get back reading forums only to conclude that it doesnt show how to do it or its wrong and not working. Thank you sir.
I have one question though on a subject Im having even harder time finding. I plug it in and INPA recognizes I have the cable plugged in. When I go into NCS Expert it recognizes it as well but when I try to load the modules and read VO it brings up "Following feature is invalid for FA: #1207" and I get it to load the codes but I cant change them. Ive read in various forums that I have to update the Daten files and I finally found a download page with V60.1 I think...Well now I have no clue how to update them. Ive tried manually copying them into what I thought were their respective folders but it actually made the program work less and gave me more errors. I had to reinstall your method again as I lost where I went wrong.
Anyway you can help guide me what forum (theres so many) you may have learned to update, etc? I have a mac running Windows XP 32bit virtual machine. Trying to code on a 2008 335XI (has JB4, this couldnt be an issue could it?) . I should try it on my e46, maybe its my car, or maybe my cable...
Sir, You rock. Yeehah! Following your astonishingly clear instructions I'm up and running on a Mac Air with Windows XP, using virtual framework Parallels Desktop 7, on Mac OS10.6.
Btw This is NOT a criticism but the very first step in the pdf instructions seemed to be missed out - Updating the System Variables Path.
A note for anyone else doing this and having errors after running the Install EDIABAS etc (Instprog.exe at 8:52). At the end when you hit the Exit button (9:25 in the vid) it can take a while for it to close. Just wait for it to close itself. It is definitely working in the background and the first couple of times I force-closed the window which I think was the cause of subsequent errors. The more of the modules you 'Check' to install, the longer it seems to take.
if ppl are still searching try bimmergeeks or google mikes easy bmwtool. mikes tool just unzip install done. both work i tryed them
Hoping you can help here. Bought one of these inpa cable and cd packages off Amazon. My computer wont run it because it says it has a malware virus inside, any idea?
Thank you for this! Looking forward to the instructional video on how to do the actual coding!
Just wanna say your videos freakin rock man. Keep up the good work! There should be a way we can pay you a little bit for this content!
Brilliant video. I just installed it on my Windows XP pro, thank you for the video.
yes my very much awaited video. Thanks
Hello 50's KID... perhaps you've some instructions pointed at disabling/removing The "ews" features from the DME...My same vehicle is the 2004 E60 545i. produced in may 2004. Inpa error codes are 2737 & 27A4... Perhaps there a preferred way to contact you? (youtube doesn't allow?)
I ran INPA 5.0.8 on every single Windows version after XP (Vista, 7, 8 and 10) with no problem. So before messing around with a virtual machine for no reason (unless you dont want that stuff on your physical computer) you should get this newer version. 6.4.3 is only essential if you want to diagnose older BMW without OBD. But then you also need another diagnostic cable.
the virtual machine was done because ncsexpert won't run on a 64-bit system.
+50sKid The version that comes with inpa 5.0.8 runs on x64. I am running it on a Thinkpad X200T and T400. Both Windows 7 x64.
Thank you so much for helping your community.
Thanks for all the amazing videos, super informative and helpful - Thank you!
Great tutorial. But, gosh darn it, I copied the wrong NCSEXPER file in the very last step. I copied NCSPRINT by mistake. Now it's all in German. Lol. I got too excited for the end, because all my previous attempts to install with the CD that came with my cable kept throwing errors to paths not found. This tutorial is great, well articulated, and everything works like how it works in the video... Just be patient
So if you google "ncsexpert in english" you will find a link to the forums where someone has attached the proper file that you need
that worked!!! thanks. first froum too, bimmerforums www.bimmerforums.com/forum/showthread.php?1594236-NCS-Expert-in-English-!
"BoolD30" post
Hey can you verify if you can read injector readings. I keep getting an error #100. This is for e90 n54
This is a freaking fantastic tutorial video
thanks!
so glad you made this really straight forward
He's a good teacher.
Hi 50skid.I have a bmw x5 e53 2001.. 2 weeks ago on my dash apear transmission failsafe when drving.. And need press pedal gas to deep to keep driving because few like stop its to hard to make runing.. But if turn off and turn on again locks like no normal.. Runs good and transmission works good again.. This happen sometimes when stop on ligth for a second.. Bring to mecanic but dont' find anything.. Can you tell me what can do.. Thanks..
50sKid could you help a dummy to set inpa on my laptop?
You can also mount an iso through VMware if it's outside the VM
Hey there, can you upload the INPA software again please ?
tried downloading the BMW software and it keeps saying "archive size limit exceeded"
Man, this is very helpful video!
Thank you so much! Much appreciated :)
hey^^ it works on win 7 32bit too, i just tested successfully
nice
Hi bro, I have a used BMW, F20 110i year 2012, imported from Japan...FM radio is set to Japan frequency, I do not get local FM channels, can I change the FM frequency to my local country stations through INPA/NCS Expert? Kindly provide me a link or a clue where to start? Thanks
Excellent Video. Thanks for an outstanding presentation !
Hey boss. I am planning to do coding on 2005 bmw 325i. Is this cable works on it ?. I looked some comments they said this cable doesn't function proper because pins . It should be 7 pins. Is it true. If yes then please advise.
hi 50 kids i already set up like your instructions but when i plugged it to my car(e90 320i) the inpa not recognise my ignition only battery on and ignition not on, do you know why?hope you can help me out this is my last step,thanks
Great issue and thank you very much. Hopefully see in next share
What settings are you using for the virtual machine? I"m running windows 10 and when trying to start a virtual xp machine, my computer reboots as soon as I start up the VM. Thanks
Great video @50sKid, all the download links are broken on the message threads, any chance of help sending/finding it? Thanks.
So this is what I'm looking for did a xhp stage 3 and paddle shifter dont work , car hauls ass but no paddles
hi, need some help. i have it installed, v5.0.0 on my e46 INPA can read the digital and analogue values, it can read in detail the DSC fault codes, but wont read the engine codes in detail. when i select s54 engine it says 'versions do not match. Malfunction possible' Any help would be appreciated (Windows XP)
Hi mate.
As good as this programme is.. Could you tell me your views on the 'Carly for BMW' app? I've recently bought it, plus some of the addons, but still using my own obd2 wifi adapter instead of their £50 version, and for what it does I think it's great although a lot of functions aren't that clear. I'd like to hear what your thoughts are on this app if you've used it, or if not, could you do a short video on it as you explain things a lot more clearly than your average instructions.
Daz from the UK.
E61 530d 2007
Never used it
I think there are better tools for the money, in this case you are paying a useful app to use with your phone, but I think that for the price you could use (much) better tools to use with your laptop.
Nice car Daz! Exactly the same as mine over here in NZ. The Carly is very good for simple reading and diagnostics but beyond the basic updates like battery registration and changing and fault code resets it doesn't have a patch on the depth of what you can do with this software and a $15 cable. And every time you want to do anything functional in the App it seems you make a 5, 10, 15 euro payment. I understand that their pro version of the App and coding may also now be restricted to using their own Wifi Adapter, the price of which seems to keep going up.
Hey, can you maybe install the cable again. I have the same installation CD and the same cable. Again, if you have spare time! I really have trouble installing my cable. Thank you!
Im still confused. Do i still need to run VMware workstation if my computers OS is actuary XP 32 bit?
Thanks for the video. Have you ever done steps of ECU software update?
When you register your account do you use bimmer as your password at that time? I am only asking because when I went to register they asked for your full name, email and password. Just wondering if I should use bimmer as my password.
I've got everything installed and working properly but cant seem to remove codes from my E64 so i'm guessing it doesn't support my 650i Convertible? What are your thoughts on this and let me know if there's a fix. I've also got all the latest updates into INPA as of today thanks.
Hey 50sKid - thanks for putting up this fantastic Video. Do I absolutely have to use COM1 for the serial port? I have COM1 currently "in use" so I opted to use COM2: is this going to be an issue?
whatever is using com1, find it and change it to use another com port, then reboot and you can use com1 for the cable
Thanks for the response. Just installed everything and it works great. Thanks for putting up such a fantastic video
Thank you so much, gonna get the PC going when I get home
I have an 03 540iT, got a 97 540i6spd because the more pedals there are in a wagon, the cooler it is
I'm gonna consult the forums for post facelift auto to manual coding because that link is dead, but nbd
Will a Creater Scanner synchronize ews and dme on an e46?
If so, what model?
I ordered this item and I received a broken CD in it so any solution you have to me is this possible without CD plz help me
Link in description is not working plese update it :) But nice videos thx you man!
im very new and 50's kid has helped me do tremendous things with my bmw that i never would have dreamed of doing, the vids always give me confidence and always work 100 percent....but the one thing i would like to know is WHAT CABLE DO I BUY? i bought an older laptop with windows xp followed these instructions and it worked perfectly, but i need a cable with a 16 pin to serial port (since this laptop has one) that will also allow me to use my 16 to 20 pin adapter for my 323i. im at a loss which cable i am supposed to buy. 50;s kid please help!
ps the cars ill be using it for are a 2004 325xi, 2004 330xi, and 2000 323i with the obd2 and 20 pin under the hood
link now working now. any other link from were i can download it?
how about using it on a windows 10 64 bit system using the software compatibility settings for windows XP?
Another great video from you!
Have you thought about to make a video about installing BMW-TIS ? It's also lister at the 4shared link in the comments. I'm sure a lot of people would be interested and appreciate it.
I can do that
Can you help me out? I have a 2006 E46 M3 SMG. I bought software and a cable on EBay but discovered that my BMW model was not included. Could you point me to some where I can get the complete software package that will work on my M3? I’ve looked at so many packages I’m cross eyed and confused.
Look into ISTA rather than INPA. It's newer and covers more.
can you send me the link to for the four folders? I cant seem to find it. Thanks
Is there a new link to dowload the ipa software?
will this update DME software.? thanks!
Do these things work with WIN 10? I see that your video is still using Windows XP. Ok you just answered my question. So, what does a person do if they don't have obsolete hardware and software?
Help please. Hello, 50sKid im getting Error #28 IFH-0018, I have a windows XP IBM T-60
Hi so I’m trying this out in sept 2020 and all links even 4shared links are broken, any way you can email me the download links ? Or maybe I can pay you to mail me a USB w the programs ? Thank you
its not working for me. once i go to E90 menu i get error on every single option i choose
Hello my name is angel I have a m73tu swapped e39touring and I have an issue that I can’t seem to find anyone to help me with. I have a laptop with bmw softwares that I bought off eBay a while back and I used to be able to switch between OBD2 and ADS to connect to my cars but something happened while a tuner was remote tuning my brothers tdi through team viewer and I think he might have moved some settings but now my computer only communicates via ADS and I need it to be able to communicate via obd so I can use sss progman to code the dsc module in my e39 any help would be greatly appreciated thank you✌🏽
Do you think ista software is better?
The file link that you requested is not valid.
4shared not working
amigo 50s kida por k no subes un video de como cambiar el vidrio de atras, de un bmw 328i 2998 te lo agradecere mucho
links all dead again...all they seem to have is the mike ez install but it does not have one series or mini coopers R50, etc.
So i have windows 10, am I in with no chance of doing this?
Current link not valid. Any updated link?
can you also make a video how to tune your ms42 and ms43 (how to increase the rev limiter, advance timing and so on...)
just not working at all...and i followed everything 2 times....reading some codes DDE40 not found etc... ncs ex not working also
I need your help bro i installed it on my laptop Microsoft XP and inpa and othet programs downloaded but when i open everything shows except a few icons dont like F1 F2 AND F10 show and the others are missing. Am i missing files
I have a same thing... Did you find help?
can u pls upload it again coz link not working
kareem Osman any luck finding a download link?
How to install ADS serial port interface?
The link is broken, can we get an updated link please?
Hi guys! Could you upload new link to this software please. Link is incorrect((( HELP please
any luck ???
great info mate
are you still active.... need help please. Mikes tools is total BS. Errors IFH0018 = OMITEC problems over obd,, 0009 and 0004. like i said that software is total jank. I need this 3.01. that one was perfect from day 1. cannot find it anymore...
the 4share folder is gone but for anyone looking i was able to find a download at www.car-auto-repair.com/bmw-inpa-6-4-3-software-free-download/
I keep getting Error 98
SYS-0008 JOB NOT FOUND
Please help🙏🏾
Tank my friend!!!
wow , why cant it be a click to install and be done.... wow . also I see people saying use a spare laptop , is there a reason why I cant use my main laptop ?
How much does NCS expert cost??
Thank you for such a great tutorial, however, didn't work with my '11 328i e90.
Didn't work with Windows 7 and I tried it on an XP laptop.
After successfully installing it on XP, INPA worked flawlessly, however, NCSexpert didn't.
The error code I was getting is "Following feature is invalid for FA: #0910".
Any help would be appreciated!
Solved it on my own. Simply updated the SP-Daten files and all is good now.
Again, thanks for the great video, couldn't have done it without it!
Good morning, first of all thank you for the good work, your videos have helped a lot, but I have a problem I am not able to connect my E46 in the NCS EXPERT of a VIN number error, at INPA I am able to enter.
With my E60, it works well with both INPA and NCS EXPERT.
Anybody knows where I can download this program for free? For my 2009 BMW I have Windows 10
the file link requested is not valid please someone re upload this.
Guys, if you still need the NCS expert software -> go to 4shared and search for INPA 5.0.2 Thank me later!
Can't download NCS expert. Link closed?
Is it possible to get a copy of your config file? I've been using only INPA and just realized that the config is in German
+Benedict Marule search for "use inpa in English" on google. Someone posted their file on the forums
thanks, found it
Download link?
software link broken?...
bump
Thank you very much!
Can you make video for DIS software ?
Hi 50s kid.thanx.I have winkfp in german and version is 4.5.1.anyway to change the language to english or install just the winkfp to a english version.dont want to undo or mess everything else.
look through the files in the directory for the one with the german phrases you see when you use the program, then search the msg boards for the english version of that file.
Will this work for 2012 335i n55
Yes
Now my problem is I have windows 10 and I can’t download windows xp anymore to install this program. What should I do ?
Thanks
When I got to 9:24 a pop up came up that some PATH is not found? Link to the pop up image here: i.imgur.com/fL0ZAcp.jpg
Any ideas what went wrong? I am installing on Win XP Pro 32 Bit but I don't have a cable yet so I was doing it all on the laptop from where the point where you download and install, I skipped the cable and driver bit. Is that why it went wrong or is it something else?
Yeah sounds like you need the cable first
Do I have to have it plugged in to the car aswell?
no just the laptop
The link with download is not working, can you upload it again?
bump
My ncs expert is still in german Copied the txt file from step 2.........
why comp 1 and not comp 4
Thanks for that amazing video can u send me a link to download inpa i just cant find a way to do that please help😢