Rough Country 2.5 Inch Lift Leveling Kit Install

[@Notime2waste_tito]

I'f you are doing this in 2024. The rear blocks that go on top of the leaf springs are sloped. I was told by a rep a RC that the slope goes towards the front of the vehicle. Just a little bit more information. Great video. By the way, it helped me do the installation flawlessly

[@AnonymousYouTuber10]

Video was useful while installing. Thank you for making this video.

[@ColbyDial]

Great video! Thanks for the detailed walkthrough.

[@helioacid8182]

whats the angle on the cv axle with this kit

[@juancarloshernandezgarcia950]

Exelente. Video u exelente explicación

[@MaggMagg-pq9uw]

Why the back too?

[@griffinherbst]

Just attempted this install this morning and i installed the lower strut bolts backwards as i couldnt figure out how the hell to get them to clear the cv axle

[@MrXcbravo]

I have the same truck but it’s Silverado thinking I’m going to do the same thing . I have 265/70/17 toyo at3 on it wish would of waited and got 285 but it’s going to have to do , 👍 nice truck

[@alexnance4954]

I had a third spacer that went under the spring on my strut and I just could not get anything to work at all

[@bradencarpenter6817]

MIght be a dumb question - if you're strictly wanting to level the truck out, not necessarily "lift it up" at all, do you have to put the rear blocks in? Or can you just install the front components to level it up and skip the rear? Brand new to this - trying to read up before I buy anything. Thanks

[@drew5992]

You can just buy the 2inch level kit for $30 bucks

[@totaltism863]

has anybody figured this out? i feel like i could just do the lift on the front an not have to put new block in the rear or do i have to?

[@arnulfob3454]

Did you need to take it to get a front end alignment?

[@treybaker4537]

Would you recommend getting the upper control arms for a lift or do you think it is not needed

[@drew5992]

Not really needed in my opinion for 2.5 inches and lower. I do recommend on 6 inch lifts

[@gala83filmstaylorg7]

How was the ball joint angel?

[@alejandrogomez7940]

So I got a 2.5 leveling block for the bottom of the shocks. Mzs I’m sure brand don’t matter but they look like the one in the bottom. It didn’t come with the plastic piece on top of strut. Everything is put back together and my front axle rubs on the bolts for the shock up top. Do you think it’s because I don’t have the spacer up top that’s why it rubs? If so do you know what size the top spacer is? The bottom one is a 2.5

[@JayyMoney-vr7nv]

Did you fix it?

[@adamdomonski1619]

Flip the bolts upside down like in the video

[@MrGoosetafer]

Do you think, when you weigh cost vs performance, it's better to lift a truck with blocks or with springs?

[@motivatedmotorsports953]

Depends on what you are wanting to do. If you are just wanting a small lift for looks then blocks are the way to go in my opinion. If you are actually wanting to take it off road and crawling, or doing a large lift for looks, then doing a proper lift with springs and brackets is better.

[@mariovelazquez9138]

Looks good

[@chamferreyes6747]

How much would a shop charge me to install a 2” leveling kit

[@Kyle-ev4fk]

Depends on what color your truck is...

[@jackmanning4006]

What size rims do you have

[@mocheeks709]

If all else fails, follow the instructions

[@shenanigansalv317]

I'd give it a F@#$n ten lol

[@adamdomonski1619]

Do you need the top one to make it 2.5”?