One of the most admirable things about your project videos are the execution of your project and its design are always functional and neat. The hall mark of a professional. Keep it up and thanks for your inspiring vids.
May I ask you, the voltage reference, shouldn't it be taken from the output (battery) voltage? Wired as it is, it has no feedback on charge status, therefore will not reconnect upon discrhage. And is fully dependent on input variations, which I understand is not desirable. Regards!
Nice! I guess we can replace the pod with a normal one and adjust the voltage for every battery, with this we can charge all kind of different batteries, isn't it?
@@RJEDITALL My question is : Do i have to calibrate the circuit every time i want to charge a different voltage battery? For example, i must make new calibration for a 3.7v battery and again a new calibration to charge a 12v battery? What do you think? Thanks.
SIR KYA IS CIRCUIT SE 4 VOLT KI BATTERY KO CHARGE KAR SAKTE HAI.please bataye.AUR SIR KOI AISA AUTO CUT CIRCUIT BANAYE JISMAIN HUM VOLTAGE KE SATH CURRENT KO BHI CONTROL KAR SAKE AUR US CIRCUIT 4 VOLT SE LEKAR 12 VOLT TAK KI KOI BGI BATTERY CHARGE HOSAKE.PLEASE SIR JI.
Please reply... Can I use the same circuit for my car?? I want the output to be OFF when engine is running i.e. voltage is above 13.3V. But the output should be ON when engine is not running i.e. when voltage is below 13V.
Pls pls pls ans 1.autocut howar por battery voltage abar kome gele ki punoray charge howa shuru hobe? 2. 4v battery er jonno ki ki change kora lagbe,and cut voltage koto hobe
@@RJEDITALL vi arek bar pls reply den Apni chance lkhchen naki change Jodi change likhe thaken to apni 12 v rellay babohar korchen, ja 4v supply e colbe na
Mostly 12v Relay turn on at 6 v but it will turn off at 2v for again charging the battery but battery voltage will not go to even 9v to turn off the relay the difference in on and off voltage of relay will always 4v so tell me how I can reduce the difference in on and off voltage of relay
@@RJEDITALLI don't understand how you can adjust the cut off voltage using the potentiometer. How the potentiometer works? You do not used zener diode to make the cut off voltage!!
@@RJEDITALL Sir i really want a similar circuit for my car which will indicate that whenever engine is running i.e. over 14V, it will show green colour, and whenever engine is off i.e. below 13V, it will show red colour. Please kindly make a new video above this. I'm trying to write a diagram but really confusing about it's accuracy of the cut off voltage say at 13V.
It seems the cut off voltage is not accurate. You set to 12.8V. And the output is GREEN when input voltage is 13.7. So, how to get more accurate circuit diagram to automatically cut off at 12.8??
@@RJEDITALL I just watched it. So using COMPARATO IC is more accurate in getting the set cut off voltage. Whereas NPN is very less accurate for the cut off voltage. Is this correct?
One of the most admirable things about your project videos are the execution of your project and its design are always functional and neat. The hall mark of a professional. Keep it up and thanks for your inspiring vids.
U welcome bro, ❤️❤️
Buenos días amigos saludos cordiales desde Agua Dulce Veracruz México buen proyecto gracias por compartir
U welcome bro, ❤️
Muy bien amigo👏👏👏👏
Thank u bro ❤️
Sir.. Thanks a lot...for provide this video..i search every Where but can not find this kind of video..
You are most welcome
May I ask you, the voltage reference, shouldn't it be taken from the output (battery) voltage? Wired as it is, it has no feedback on charge status, therefore will not reconnect upon discrhage. And is fully dependent on input variations, which I understand is not desirable. Regards!
Ei achei muito massa. gostei
Thank u ❤️
Discovered your channel by chance. You sir have one new subscriber.👍
Welcome to my Channel ❤️
High tech and sense thank you
Nice! I guess we can replace the pod with a normal one and adjust the voltage for every battery, with this we can charge all kind of different batteries, isn't it?
You can use any battery charge , up to 18 ah
@@RJEDITALL My question is : Do i have to calibrate the circuit every time i want to charge a different voltage battery? For example, i must make new calibration for a 3.7v battery and again a new calibration to charge a 12v battery? What do you think? Thanks.
Nice Video Big Bro 👌👌👌
Thank u ❤️
Wow amazing beautiful idea 👌✌️ thanks my friend 👍👍👍👍👍👍
U welcome ❤️
1
Thank you soo much sir❤🎉 then can i change lethium polymer battery?
@@lalmalsawmamsa1313 yes
Can we use this circuit for 5v battery and charger
Yes
@@RJEDITALL thanks
Slm,,desulfator olarak kullanabilirmiyiz?
Clear not understand
Hii Nice
How about using a power transistor instead of a relay
@@dnyaneshwertaral8055 ok
Work on 5V input?
@@arama8196 you try
Bro mera cerger 19.5 v or bettery litiyam 12.6 v auto cut hogi is cerket me
@@rafijuddinrifat830 hoga
Nice bro,but transformer v off( cut ) ho ya kasa banaya?????????????
Wait, ❤️❤️
Onde compro este painelzinho marcador de vsoltagem
Check description, components link in description
Creative video, thanks :)
U are most welcome ❤️
خیلی عالی بود ، مرسی
❤️❤️
What if the input is 5v. And charging 3.7v can it do the job? Or can i change some components?
Yes, change your Relay, connect 5v Relay
Thankyou🇸🇩👍👍😘❤
U welcome
Can it charge a 12.6 volt lithium battery?
Yes, ❤️
How many watts is the 10k resistor you used in it?
@@sumeshkv5118 1/2 watt
Yes
SIR KYA IS CIRCUIT SE 4 VOLT KI BATTERY KO CHARGE KAR SAKTE HAI.please bataye.AUR SIR KOI AISA AUTO CUT CIRCUIT BANAYE JISMAIN HUM VOLTAGE KE SATH CURRENT KO BHI CONTROL KAR SAKE AUR US CIRCUIT 4 VOLT SE LEKAR 12 VOLT TAK KI KOI BGI BATTERY CHARGE HOSAKE.PLEASE SIR JI.
@@sumitnarkhede.3105 ok, wait
@@RJEDITALL DHANYAWAAD SIR JI.
What Amper ?
Maximum 3A
Sir why use this diode
You try, understand
Sir can i use 3.7V 100A battery charge and auto cut it? Please ans Thanks from Bangladesh.
No bro
Is it possible to set 12.6V as cut off voltage?
Yes, 100%
what is max current that can be drawn from this?
5 ampere
relay 5v please charge 3.7
You try
Please reply...
Can I use the same circuit for my car??
I want the output to be OFF when engine is running i.e. voltage is above 13.3V.
But the output should be ON when engine is not running i.e. when voltage is below 13V.
please how it work i can not yhe relation between a limit chage and the changement of switch relay
Лампочки на какую мощность и ток рассчитаны?
All details in the video
Pls pls pls ans
1.autocut howar por battery voltage abar kome gele ki punoray charge howa shuru hobe?
2. 4v battery er jonno ki ki change kora lagbe,and cut voltage koto hobe
1. Punoray charge shoru hobe,
2. No chance for 4v battery charging
@@RJEDITALL vi arek bar pls reply den
Apni chance lkhchen naki change
Jodi change likhe thaken to apni 12 v rellay babohar korchen, ja 4v supply e colbe na
Mostly 12v Relay turn on at 6 v but it will turn off at 2v for again charging the battery but battery voltage will not go to even 9v to turn off the relay the difference in on and off voltage of relay will always 4v so tell me how I can reduce the difference in on and off voltage of relay
Will this circuit function as a battery maintainer? Great video and I just subscribed to your channel. Thanks for any info.
U welcome, ❤️
ভাইয়া এটাই কি 6 ভুলট বেটারী চার্জ দেওয়া জাবে
But lithium ion battery should get cutoff at 4.2v and this circuit cutoff is at 4.36v. Will battery gets damaged?
Please reply
Yes.
I want similar circuit function.
Minimum should be between DC 5 to 18V.
And cut out voltage be 13.3V.
Please help 🙏🙏🙏
You can with this circuit, with input 19v dc
@@RJEDITALLI don't understand how you can adjust the cut off voltage using the potentiometer.
How the potentiometer works? You do not used zener diode to make the cut off voltage!!
@@RJEDITALL Sir i really want a similar circuit for my car which will indicate that whenever engine is running i.e. over 14V, it will show green colour, and whenever engine is off i.e. below 13V, it will show red colour.
Please kindly make a new video above this.
I'm trying to write a diagram but really confusing about it's accuracy of the cut off voltage say at 13V.
What is the power of the 10k resistor
1/2 watt
Tnx
@@RJEDITALL Can it be 1/4 watt? or will the resistor get too hot?
@@jenntek.101 1/2w
Thang yuo sir
Welcome ❤️
merhaba kanka giriş voltajını 24 yaparsam neyi değiştirmeliyim teşekkür
Replay 24v
How Much Ampere it will Give
Maximum 10 ampere
Bro cerger 19v to bettery 12 auto cut posible
@@rafijuddinrifat830 yes
👌👌❤️❤️👌👌
How I charger 3.7v battery and please tell me
Full video watch, you can understand
I subscribe sir
Thanks bro
It seems the cut off voltage is not accurate.
You set to 12.8V.
And the output is GREEN when input voltage is 13.7.
So, how to get more accurate circuit diagram to automatically cut off at 12.8??
Please check in my Channel
@@RJEDITALL sir i already checked.
Please share where I can find it 🙏
@@tnamen1307
ruclips.net/video/geEky1onXoE/видео.htmlsi=wOnw9IAJW4Z4bn-K
@@RJEDITALL okay thanks so much SIR for the sharing...
@@RJEDITALL I just watched it.
So using COMPARATO IC is more accurate in getting the set cut off voltage.
Whereas NPN is very less accurate for the cut off voltage.
Is this correct?
Why do your voltmeters got 3 wires?
Yellow wire for volt measurements
Hlo sir priset k Jagah pr 10k ka potnsmitter kisa lagaya please sir give me diagram
yes, you can use potentiometer
Punjabi bhasha mein bole to Changa Bangali bhasha mein bole to Khoob Bhalo Hindi bhasha mein bole to bahut Achcha aur Marwadi bhasha mein bole to Ghana badhiya
Thank u ❤️
Sir how alarm AL-06A resolved
I want to make a circuit , when out put voltage not below than 6 voltage . Because i made a veriable power supply . So i want to that type
Check it well
V GOOD ,,,,,,
❤️❤️
Coba voltmeter nya lapisi kaca film,supaya tidak terlalu kontras cahayanya .
What transistor can I use for this cut off circuit if I need to charge a 36v battery and want it off at 41v?
Not possible with this circuit
@@RJEDITALL Yes I thought so but wanted to save some time 😉 Thanks
Memakai potensio 500ohm apa bisa?
No
❤👍👍🙏🙏
Thanx
Welcome
No and NC ka kya matlab he
NC - Normally close, No- normally open
Hello Sir, I like your video but I'm wondering if I can use KSP2222A because I don't have the BC547
Yes, you can use, please check the transistor base , collector n emitter
@@RJEDITALL Thank you Sir
Nice
❤️
Hi, can i use solar 24V to charge 13.8v battery
Yes, you use dc controller with this circuit for 14v dc
@@RJEDITALLlink please for dc controller
@@madeintanzania2995 please wait
@@RJEDITALL that's why i liked your channel...! It's my hope that your next video will be it🙏
Mana link cara membuat setrum ikan
Please check the description
👍
❤️
One Question if we set cut off 14 v. When battery reached 12v. Automatic battery will charge automatic?
Yes, charge automatic