Guys kindly support us by following us on Instagram @smilin.sun and Facebook @smilinsun , This is how you can support the work we are doing. Thank you so much.
Is that a Lead acid battery? Anyway, the quality of the product depends on where they bought the battery. I have seen some shady LiFePo battery cells which when measured don't produce any power (Zero Volts) and on cutting through the cells, i saw it was filled with sand. That is why it would charge and lose power quickly because half of the cells were fake cells filled with sand, so the configuration of series-parallel was being run by few cells.
My naija lithium lifepo4 manufacturer said I should charge my 24v battery tooth 27.8v. Na there I de so since. Though I'm thinking it's low, but wetin I fit do? I've to obey
Is it possible to install different brands of solar panels to the same inverter for example Jinko and Africell panels together to feed the same inverter.
@@smilinsunsmilinsun8056 I was convinced to use Africell panels but later found out that Jinko is better. I wanted to buy Jinko for better performance. Is this a good idea?
This can is serious. But if charge controller could overcharge the battery, what then is the function on BMS? i guess the battery cells has to be a substandard one or the bms is also substandard.
All the information you need is on the manual but most people don't read the manual. Reading the manual is one thing and knowing what to do is s another
I have a question about lithium battery, though new, bought last week , but not really gotten enough charge , but the percentage of both battery are not same , one is higher than one. I noticed one battery is 18% while the other one is 9%. Right now they have 12, 550watts panel with 10kva and 20kwh lithium, no plans to charge with nepa at all. What do you suggest
Thank you for the information on SPD. I really appreciate it. What is the formula for determining the size of each protective device, eg. between solar panels and charge controller, between charge controller and battery etc?
Guys kindly support us by following us on Instagram @smilin.sun and Facebook @smilinsun , This is how you can support the work we are doing. Thank you so much.
Correct it also depends on the number of cells in the battery
You are right
Thax boss
You are welcome Buddy!!
Is that a Lead acid battery? Anyway, the quality of the product depends on where they bought the battery. I have seen some shady LiFePo battery cells which when measured don't produce any power (Zero Volts) and on cutting through the cells, i saw it was filled with sand. That is why it would charge and lose power quickly because half of the cells were fake cells filled with sand, so the configuration of series-parallel was being run by few cells.
Wow! This is new information
What about those using a hybrid inverter which has inbuilt charge controller...how do you know?
My naija lithium lifepo4 manufacturer said I should charge my 24v battery tooth 27.8v.
Na there I de so since. Though I'm thinking it's low, but wetin I fit do? I've to obey
Tell us your experience about a Lithium battery set up, what has been your experience?
It doesn't work that way. The bms handles the charging
The function of the BMS is not to select the charge voltage , that is the function of the Charging system. BMS can only try to regulate or protect.
Very good video. But does the solar panels have to be the same brand with the inverter and battery?
No You can use any Brand of solar panel you want
Well done Sir! Is this also applicable to Tubular battery?
No most Charge controller settings are correct for flooded batteries
Is it possible to install different brands of solar panels to the same inverter for example Jinko and Africell panels together to feed the same inverter.
@@samisaac3908 Not a good idea stick to one good brand
@@smilinsunsmilinsun8056 I was convinced to use Africell panels but later found out that Jinko is better. I wanted to buy Jinko for better performance. Is this a good idea?
Next time, remove the background music. Thx for sharing
Noted, Thanks for watching
Or at least turn it down about 50%
This can is serious. But if charge controller could overcharge the battery, what then is the function on BMS? i guess the battery cells has to be a substandard one or the bms is also substandard.
Whatch the video to the end your question was answered
did the bmses inside those batteries fail?
Why is the setting not written on the manual for safety on each?
All the information you need is on the manual but most people don't read the manual. Reading the manual is one thing and knowing what to do is s another
any after effects on staying in a room where Tubular battery have been stored
Depends on the type of Tubular Battery and the quantity of battery
Maximum voltage for lifepo4 is 3.65v
Correct
Can't you drop down the voltage setting on inverter to meet the charging voltage on lithium battery
Yes you can by going through the User defined option
Hi I got a closed loop communicating on my batteries and my assumption is BMS will take care of everything am I wrong?
For lithium battery without BMS
I have a question about lithium battery, though new, bought last week , but not really gotten enough charge , but the percentage of both battery are not same , one is higher than one.
I noticed one battery is 18% while the other one is 9%.
Right now they have 12, 550watts panel with 10kva and 20kwh lithium, no plans to charge with nepa at all.
What do you suggest
There is a communication glitch between the two parralled batteries. They should all be charging and discharging at the same rate.
@@smilinsunsmilinsun8056 thank you , also bout the solar for charging, whats your advice
Are they both charging with the same charge controller?
@@theo2378 3 Hybrids in parallel
Please, how much did you get the lithium battery??
What happened to the specification label on the battery sir.
Please kindly watch the video till the end the question you are asking has already been addressed
You are correct... I dropped the comment before watching the video till the end. Lol
Thank you for the information on SPD. I really appreciate it. What is the formula for determining the size of each protective device, eg. between solar panels and charge controller, between charge controller and battery etc?
Not sure I understand, what battery specification