I converted my 5x10 utility trailer into a dump trailer / DIY dump trailer
HTML-код
- Опубликовано: 8 мар 2024
- I was in need of a dump trailer for some home projects so I converted my 5x10 trailer into one. I used an electric winch and mast system to do the lifting. #dumptrailer #diy #utilitytrailer #fabrication #welding
Авто/Мото
Extremely nice job. A bit over-engineered for what you will use it for. I thnk you will tire of holding out the pin while raising and lowering. The amount of time it will be in the raised position will be minimal and nobody will likely even be close. The cable system by itself is strong enough for the use unless you plan on hauling lead pellets, which would overload the trailer's capacity anyway. I have hung heavy speaker systems in commercial buildings using 1/8" cables. Properly terminated, they are extremely strong. Anyway, if this helps you sleep better at night, more power to you. Really nice craftsmanship. Looks like it was built in a factory.
It’s definitely overkill but hey why not. The safety pin was meant to be “temporary” because I have another design I want to try but who knows when I’ll get to that Lol. Thanks for watching.
NICE BUILD.
Subscribed.
Nice Job! One thing I would add is a few pieces of C channel or even angle iron to cover the winch cable, sort of belt loops on your jeans. This so if it where to break, it would be contained and not become a whip.
That is one thing I didn’t get to yet.
Great video! Kudos for adding a saftey mechanism.
Brilliant friend!
I had a 4x8 foldable northern supply trailer I used as a bed in a 5x8 utility trailer I was given and turned it into a dump trailer similar to your build. I made the 4x8 removable so the 5x8 stays original with the rear gate/ ramp operational. I did have the same challenge figuring out the mast. I welded my winch to the mast and also made it removable and height adjustable. Definitely a rat trap if something goes wrong. But the wireless remote gives you the ability to stay back and keep your eye out on others when your operating it.
Did you start with a 4x8 or 5x8? Trying to figure out what you meant. I'm wanting to make my 4x8 into a dump
@@FFRJB1971 I had a 4x8 since 2010. My brother in law gave me a 5x8 in 2020 which is way better built with a removable gate ramp. I only used the 4x8 frame and chucked the rest. I welded the 4x8 to make it rigid to carry a good load without breaking. Now the 5x8 stays stationary while the 4x8 is what tilts on pivot hinge points where the ramp gate goes. If you want to do something similar you can make a platform out of 2x4's and a sheet of plywood you'll have to add at least a 2 foot high walls on three sides and a removable door on the rear. Add some good strong hinges that attach the rear of the 2x4 to the frame of your trailer and you'll need a mast which you can make out of 2 2x4's sandwich together. This is where you can attatch your winch. The rest is hard to put into words. I'd have to show you. Subscribe to my Channel and I'll make a quick video explaining and showing what I mean. Took me a good while to figure it out but every time I go to the dump I get stares and people ask me if I would sell or make them one. I use a small plastic tool box that I fit a 12v lithium battery and the winch controller. Anyhoo let me know if you're interested I can muster a quick video. On a weekend.
@pg9112471 planning on reinforcing with steel.
Very very nice! Great job!
Awesome job
Try a good quality "Flux Core" wire for mig welding, it will not blow away in the wind.
You can always get a scissor lift kit, and maybe a tarp to cover your load.
Cool idea, just change those safety pin holes to slots so the pin can fully engage when moving. I might even widen them a bit to ensure the pin can make it in super easy.
OMG! I fell off my chair when it slammed down. Must people would of cut that out but not you. Love your channel and keep them coming. I am pretty sure you were the one who taught me how to weld over 20 years ago. Thank you!!! Best hobby I have ever had. Welding up a locking AR holder for my F250 this weekend.
Haha gotta show the mistakes too.
I had just seen ur dump trailer video. turned-out looking great. watch-out for ur fingers.. good for work around home or helping someone to move stuff.
Definitely have to watch all the limbs, pretty scary when it comes down.
Slotted holes on the safety pin but also put a 45 degree chamfer on the top of the pin then it will automatically push the pin out by itself as it travels up but lock in as it travels downward (kinda like how a door knob latches automatically when you close a door) maybe retrofit a door knob latch as your safety pin???
I didn’t do that because the pin is round, I thought about that but i need to make the pin square so it doesn’t rotate.
Nice trailer. My first thought is the hole should be a slot nor a round hole. That would give the pin plenty of time to penetrate the tower. IMO.
Cheers
I would agree round was just easier at the time.
We had 4 tripod jacks building a 12' diameter grain bin that was up about 20' or so. I was the lucky one that was using a crescent wrench instead of a handle. I company should have replaced the handle that we bought the grain bins from. The wrench slipped off the boat type wench. The only thing I remembered was the clicking sound as the tripod and the grain bin came down on me. The next day I still had the impression of a bolt that was in a culvert type building. Nothing broken. I guess the tripod fell against me and then bounced, then I fell down, then the tripod was against the building with the grain bin on top of it.
Just one of the close calls I have had.
You can never be too careful.
Scary stuff, glad you are ok!
For a dump trailer a couple of great additions to think about are an electric bed vibator, and if you live in a climate that gets prolonged sub freezing temps under bed floor heating pads
I’m in Phoenix so definitely not worried about freezing lol.
@@wallysworkin823 no but if any viewers up north might want to look into box heating
You made testing the safety lock way to over complicated. Just raise it like normal the pull the free spin pin on the wench.
Nice Job. Only thing i would make the tail gate removable easily. They seem to get in the way at the worst times.
I wanted to make it double gates originally but didn’t have another set of hinges. The one piece is a pain so I’ll be changing it.
The winch should be able to reverse and let it down as slow as it goes up the way it is somebody is going to get hurt maybe spend 900 bucks on a hydraulic sissor lift and be done with it less dangerous
It does go down nice and slow. The safety “pin” is just incase the cable breaks. I agree the hydraulics would be safer.
Everything was good except for the forklift operator smoking with the propane tank in his back
😂
I feel like you live near me in Glendale AZ. XD
Close enough, 43av and Paradise.
@@wallysworkin823 It looks like it! I'm off of 47th & T Bird. Keep it up sir, great content!
Did you shorten the length for strength?
I didn’t want the bed any longer than 10’. I shorted the frame to move the hinges forward. Moving the hinges forward takes a considerable amount of load off the winch. Most dump trailers have the hinges 2-3’ from the rear of the trailer.
I've never understood why they put the hinge inset from the end of the trailer. This causes the tail of the trailer to extend to the ground when fully raised which then drags the ground as you try to pull forward with the trailer fully raised in order to allow the contents to fully empty???
Moving it forward a little takes a large amount of load off the winch, it’s easier to lift. It’s a balance of not going too far so it doesn’t drag.
Very nice trailer. What if if you beveled the leading edge of the pin and depth so that you didn't have to hold it as you raised it. It would hold on the down but self release on the up? If that make sense? Just my thought on it.
That would work if the pin was square. Right now the pin can rotate.
Wally, you do nice work I am sure you will get years of use out of it. Down the road if you chose to sell it? You will get most of your money back you have moved past the cheap trailers when you made a dump body type , I have only seen very heavy duty duel axle dump trailers so you have something there that would appeal to many people in the trades and doit them selfers
Thanks! My friend that builds trailers wants to copy it (I was the ginny pig 😂) We also do not see too many small dump trailers around here.
Naw man the welds overall look good. Bein too hard on yourself. Got good penetration, no porosity, only a slight wander on a few of em. This is a DIY Dump trailer bud. Looks great!
Thanks!
Great execution but the trailer axle is probably rated for 3500lb . How much weight did you add to the original trailer?
The axle is 3500 pounds. My capacity is right around a ton. I haven’t weighed the trailer empty yet to know exactly
What you could do is maybe cut it at a 45 and it could possibly ratchet on the way up but quickly engage in a hole on the way down
We talked about that but since the pin is round we were worried it would rotate.
@@wallysworkin823 if you slotted the pin housing and drilled the pin for a barrel pin it would have no choice but to not rotate
Since you added so much weight in steel to a single axle trailer, how much payload do you actually have?
About a ton safety. I have put 1.5 tons in it so far with no issues.
@@wallysworkin823
Did you swap out the axle/springs?
Kept them the same for now.
So tell us, what do you do in your spare time? Very well thought out and EXECUTED! You even got me to like and *SUBSCRIBE* Hey, it don't cost nothing so EVERYONE should *SUBSCRIBE* YES?
This is what I do in my free time lol. Thanks for watching!!