Camaro Power Window Motor Replacement - 4th gen F-body - FIXED! - CarParts.com
HTML-код
- Опубликовано: 27 фев 2022
- In this video I show you how I remove and replace a power window motor from a 4th generation Camaro. I got an AC Delco replacement motor from @CarParts.com . (GM# 19251415) I used a drill to remove the rivets instead of removing the entire window regulator. The window wouldn't roll down or roll up. It's fixed now! Now I can get my Taco Bell fix through the drive-thru. LOL
If you enjoyed this video, please give it a like (it helps me out!) and browse through my channel for other informative and fun videos. If I’ve earned your subscription, please subscribe and click the bell icon so you will be notified when I post new content.
I appreciate the support!
-----------------------------------------------------
OFFICIAL DANINATOR MERCH IS AVAILABLE!
Check it out:
teespring.com/stores/the-dani...
Use Coupon Code: DAN10 to save 10%!
-----------------------------------------------------
SPONSORS:
CarParts.com - (PLEASE USE THIS LINK IF YOU ORDER PARTS FROM CARPARTS.COM) www.carparts.com/?...
-----------------------------------------------------
For business inquiries, please contact The Daninator at:
the_daninator@hotmail.com
Instagram: @the_daninator_yt
4th Gen Fourth Gen F-Body fbody Camaro Firebird Z28 SS Super Sport SLP RS Trans Am Firehawk Formula V8 V6 1993-2002
Disclaimer:
Due to factors beyond the control of The Daninator, I cannot guarantee against improper use or unauthorized modifications of this information. The Daninator assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. The Daninator recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of The Daninator, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not The Daninator.
@carpartscom
#DrivingRepairs #RightPartsRightNow #Camaro Авто/Мото
Now I can go through a drive up lane like a normal person.
This hands down was the best video I found. I ended up just using a 1/2 inch drill bit for the hole to get to the rivet. This literally made a headache of a job and 30 minutes of time into a 10 minute repair. I highly highly doubt the 3 1/2 inch holes I put in the door would change any type of structure to the door lol.
I wasn't going to like the video because of how big the holes were made, but Taco Bell is life, so not only you get a like. You also received a subscribe, thank you for the content.
Simple, straight forward solution and no wasted time watching.
Bought my 98 camaro today and the driver side window doesn’t work and you, my friend just made my life so much easier with this vid. Definitely doing this tmrw! Thank you! Oh and you just got yourself a new subscriber 🙏🏾
Awesome video. I’ve been thinking about fixing my window for awhile now but couldn’t find an easy way todo so. This video was super simple and straight to the point👍🏻
Thanks man! Just did my 01 SS tonight!!!
I went through about half a dozen videos until I arrived at yours. This explains everything straightforward and I much appreciate the video from inside the door. Thanks!
Edit: I replaced the driver's side motor on my '00 Camaro SS with the info from your video today. Encountered no problems and everything works again!
Damn you made this look easy cuz taking out that motor was a pain in the ass, but without this video it would have been even worse so I thank you. Cant believe they made it so hard to service.
Perfect video ! Without it I would not have been able to repair my 99 Camaro !Many thanks ! Congrats ! Bravo ! Merci beaucoup from France !
Awesome! Glad the video was helpful to you. 👍
I'm a taco bell fan myself and I have the same exact problem. thank you for the instructions... Very much so.. off to taco belll. Lol
Oops, I forgot about the glass dropping, Glad I watched this first and saw you clamp it up. Great time to update to a better new speaker too. Big Holes make a car lighter/faster. Hahahaha
Happy to find this video, super helpful for my wife's camaro.
Thanks for that inside door view. Now I have a better idea what the motor is doing. I've needed to replace my passenger door a while now.
But I really hope you had a mask on when drilling those holes. Fiberglass is not something you want to breath in, even just a bit
Hello mister, just wanted to say thank you, thank you for keeping it simple and fast, I just fixed my trans am window motor today thanks to your video, and of course safe some money, thank you again
My 99 z28 driver side just went out…I had a 97 ws6 and it took me almost 2 hrs to do it correctly lol. I will be putting holes in my door for the z28. Thanks a bunch man, very informative!!! Earned my sub.
I'm not first but i won't be last. Fun changing them window motors
I remember watching your video on this issue. Misery loves company!
@@TheDaninator LOL. You're not a true fbody owner if you have not done this.
Outstanding! Will be changing the window on my '99 Z28 vert this weekend. Thank you!
Dude, just wrapped up. I can't thank you enough brotha. Heading to taco bell myself right now. Seriously, thank you very much for sharing!!! You got my follow.
Awesome!
Super informative and hi-qual video - Thanks!!
I expect the next video to be sponsored by Taco Bell.😁
About the little bezel.
Hi! I've changed the loudspeakers on my 2000 Z28.
The control bezel :
You 1st have to gently remove the door panel (carefully lift it), let a friend hold it, then carefully press the metal clips of the bezel FROM INSIDE. You have just enough wire lenght to safely do it, and you'll never ever break that little bezel again nor scratch the hard plastic around the bezel.
Thanks for the video! I've ordered the passenger window motor, I guess it's just about the same as the driver side.
Excellent tip! Thanks 👍
This helped alot, super easy to do. Big ups!
I'm so glad I came around your video! my brother is having this done to his car right now but the guy doing it removed a lot and did way more then you did. when I do mine I'm just gonna drill those holes cause that is so much easier and much less time consuming! Great vid!
I mean it doesn’t take structure away and no one see it so who cares makes it easier the next time u gotta go in there also
I did one door some years ago and should have done the other at the same time but too lazy, had to watch your video to remember how to do it thank heavens for RUclips and people like yourself. The start of my problems started with a short drive just to take it for a spin, then I noticed the Air Conditioner did not work when at home I changed the relay with a new one and got that going then noticed window slow then stopped moving. So tomorrow morning I will be changing the motor (had purchased previously when I did the other side) Love driving this car but getting tired of working on it.
Thanks for the video hope mine goes as smoothly as yours Graeme in Australia.
Done ! Big holes would have been the go, I did it with smaller hole and had difficulty in getting those bolts and nuts fitted my kit came with 6 nuts and star washers and 6 bolts guess these motors from Rockauto are used for other cars as well. Anyway used the 3 nuts and bolts for the Camaro and noticed I had 3 screws and star washers and only 2 nuts left over ?. Did drop some in the door a few times but could not find it even tried a magnet no joy. Just hope it’s not next to the gear assembly.
These cars are made cheaply I noticed the door lining is made of 2 parts and held together by glue and some plastic nipples that go through the second half of the door panel then GM melted the end so it held together. Mine had come away just at one end but decided to leave it as it did not stick out. Last night I must have done this job 20 times in my dreams ALL WORKING now Big thanks.
Graeme in Australia
Better than a service manual!
Thank you for the help. Just did the motor in my 97 z28 and it works great now
Awesome!
So cool! Thanks man! I am about to do this on my 1997 Firebird this weekend! :D
Hey Dan. Good video. Power windows age great. If they work. Thanks for sharing. 🍁👍👍
Thank you Sir! We did this to my 1997 30th anniversary Z28 after watching your video,,,, Worked great!!!
Awesome! Now you can get tacos too! Lol
@TheDaninator ,,,, Thank you so very much! Followed your video step by step and I’m back in business, just finished it up, 1997 30th Anniversary Z28
Taco bout a job well done. Another great video. I don’t think the holes were a mistake. You planned with the info you had. That’s how we learn.
I see what you did there 😉👍
My 2002 Firehawk, and I thank you. 👍
I can concur Taco Bell does make you make crazy decisions before and after you have it. Lol
Best video for this ! Thanks
Thank you for your public service! You're indeed a hero! How did the motor hold up over time?
So far so good! Still getting tacos. 😄👍
Nice hardtop! About to do this tomorrow
Well mine just took a crap for sure. You made it look easy so I guess I will order the part amd start the process.
...as far as Project ZRS goes, I've had so much going on with family, work and other projects/obligations that I've not gotten to work on it. But, that's not to say that stuff isn't happening behind the scenes with it. I was able to find some parts that I'm super excited to share with you, as soon as I can get to it!!
Grabs wooden paddle bit and proceeds to drill through door 😳.... Grilled Cheese burrito here I come!great idea with those clamps on the window glass 👍🏾.
😂 is it wrong if it worked? Cheesy Gortita crunch is my go-to!
@@TheDaninator we gotta do what we gotta do 🤷🏾♂️
Very nice
Dreading the day I need to do this to my bird. Looks simple enough though. I really need to address the power windows on the Poorvette. 😬 nice job bro. Oh, lay off the Taco Bell. There’s only so much raccoon meat a guy should eat. 🤣
If eating Taco Bell is wrong, I don't want to be right. LOL
🤣🤣
Racoons meat 🤣💀
My hero
Lololol I laughed so hard when I seen his drillbit
Gotta do what you gotta do !
Looks like a fairly simple fix, hopefully not too many go off on the spade bit usage🤣.. ✌
If it works, is it really a bad idea? 🤣
Not sure if there was a slow death with this window but my passenger side is basically dead. It would go some down but stop and it would move again after sitting for a few minutes. I had to pull up on window while using button to get it to close all the way. Now it's just unresponsive. Assuming it's the motor, both window buttons had the same results. This video will help.
Good job Dan!!
Wish I had my camaro still, but I would just settle for some tacos 🌮 😝
I just did this on My 98 trans am the drivers side was easy but my passenger side window is stuck down....hope I can do it the same way I did the drivers side
I still remember the uneasy feeling I got when I realized the fourth gens doors were all composite. Seems like there would be a crash bar or something in there!
You’re right! Nothing in that door, I’ve got video evidence. 😵
Comment repairer les rives pour faire les trous
damn 😿
Will this procedure work with a 1995 Trans AM? Thank you!!
Just got a 2002 Camaro SS and drivers window will go up and down but super slow and won't go all the way up leaves a little gap I am assuming it just isn't strong enough. Passenger is not working at all. When you were testing the new motor do you have to realign the gears?
Ended up using my electric drill after I broke 2 bits on the cordless 😂 them GM rivets were made to last but not the window motor
Question im not sure if it my motor because the switch wont move the passenger side either, but I already changed the switch and the pigtail and the drive side still wont do anything either side but the button on the passenger side works fine so j know the fuse is good im stuck
Does anyone know a different way to keep the window from falling down after removing the motor? I'm not sure if I have a clamp like he shows. Also, can I drill through the fiber glass with the same drillbit used to remove rivets? (Wear a mask when cutting fiberglass)
what type of rims are on the camaro i want those but in chrome
Pontiac GTO
For the switch bezel that’s why I just buy the whole switch off eBay for 30$😊
What kind of b.s. that they're riveted in? When they knew damn well those motors and regulators would go bad. Do you still have to drill out of replacing the entire regulator?
my window is stuck down and their are no rivets. what do i do?
What’s the L R button on the door?
That’s to adjust the left and right side mirrors.
Too bad there are not upgraded motors that last, I'm on my third one from original.
That stinks!
Weight savings
WHY ARE THEY RIVETS. come one GM, did you really think you make stuff to last? Lol
Spade bit.............................
They are not 70...........LOL
Notoriously shitty motor ive replaced mine like 4 times….since 99
Yikes!