This is sick only saw it with 2 dashs and this is perfekt for me only 1 dash going to make this but with also a switch to switch between dual or rear or front engine only
Nice😮 i have 26.4 amps with extra batteries. I thinking of to get a 3d print to extend battery cover to get one more 12.8 amp extra for really lång journeys. But what if i do it with dual engines. But do I get good distance? I mean dual engines more power but dont need to push accelerator as hard? I got bettet peak performance but if I run on flat surface then I dont need push hard? Does that equal out?
I was a rookie and didn't follow your last instruction on the video and I bricked both my controllers... Anyways I've ordered new ones but my question is: How can I program both controllers while they are both connected and powered up by 1 dashboard? Do I have to program them separately by unplugging 1 controller > program the other> plug controller back in > unplug the other > then program the plugged one > then plug them back in parallel? I know a simple solution is to install a second dashboard and hide it somewhere in the stem or deck but what if I don't want to do that?
Hi mate sorry to hear it messed you around. You can use stlink to recover the controllers easily most cases. You will need to do exactly as you explained and power them individually using the data cable individually also. Good luck with your build bro 💪
@@mkfixitscooters308 Wait, is it really that easy to recover the controllers? What happened was that I had all parallel cables connected to both controllers except the battery ones and once I plugged the power cable in 1 of them both controllers somehow turned on and after that both controllers bring up error 28. I checked all MOSFETS, resistors and connections between the phase connectors & MOSFETS and they all seem fine. Also there were no burn marks visible.
@@rafganX strange. best to program both individually. Power always make sure either one is connected at a time or both are connected as I do using a parralel cable THEN connect the battery
@@mkfixitscooters308 It seemed that if I had the data cable connected on both controllers and then connect the power cable to 1 controller (while the battery is connected), it would supply 5 volts (red light comes on) to the controller that didn't have the power cable connected and also trigger the dashboard and somehow mess it all up.
sorry for the late reply but we are not sure. We have heard of diodes being used but have never tested. You could run 2 dashes 2 data cables and just link the throtle that would show speeds of each controllers
Do you sell the dashboard connection, I would like to do that but with a external battery beside the 48v monorim batterie is it possible to join to have more autonomy, good job by the way
Connections Motor Phase Inputs External Same From Mainboard On Scooter To Controller Of 2nd Motor To Phase Inputs Externally Same if you connect It will work smoothly
Hi, I replaced the control unit on my Xiaomi 365 PRO scooter and it gave me error 35 (mismatched), how do I pair the new control unit? What is the procedure, what to do??
Why you just not connect the hall sensors from the second motor-controller to the dashboard? I think you was confuising the dashboard with both readings. Just make it work like a master/slave
@@mkfixitscooters308 genius! Love it mate. Definitely following. Second the other guys comment, would love to see a m365 controller conversion to 72v if you ever find yourself bored haha
Gracias por hacerme perder 1 chasis de m365 y 2 centralitas. Hize lo mismo y no aceleraba ninguno. Despues, lo puse a 2 pantallas y auk asi se volvia loco y se ponia a 56 un motor y el otro a 40, hasta q como no paso lo q tuvo que pasar. En recta se quemarok los controladores. Y hablo de 2 dias despues de toda la perdia de dinero y tiempo invertido.
Es tu problema por no hacerlo bien, yo tengo las dos montadas como el tio del video y sus otros videos y me va perfecto me pilla 55-60 con dos motores de pro2 y dos controladoras v3
@@mkfixitscooters308 yeah i just messaged about this... i didn't see any AWD files. I'd be fine flashing separately, but I'd like to know the settings on each motor based on your experience
not sure, but if you have screen with speedometer you can also if you use shfw use the screen to show battery percentage or something
This is sick only saw it with 2 dashs and this is perfekt for me only 1 dash going to make this but with also a switch to switch between dual or rear or front engine only
Nice😮 i have 26.4 amps with extra batteries. I thinking of to get a 3d print to extend battery cover to get one more 12.8 amp extra for really lång journeys. But what if i do it with dual engines. But do I get good distance? I mean dual engines more power but dont need to push accelerator as hard? I got bettet peak performance but if I run on flat surface then I dont need push hard? Does that equal out?
I was a rookie and didn't follow your last instruction on the video and I bricked both my controllers...
Anyways I've ordered new ones but my question is: How can I program both controllers while they are both connected and powered up by 1 dashboard? Do I have to program them separately by unplugging 1 controller > program the other> plug controller back in > unplug the other > then program the plugged one > then plug them back in parallel?
I know a simple solution is to install a second dashboard and hide it somewhere in the stem or deck but what if I don't want to do that?
Hi mate sorry to hear it messed you around. You can use stlink to recover the controllers easily most cases.
You will need to do exactly as you explained and power them individually using the data cable individually also.
Good luck with your build bro 💪
@@mkfixitscooters308 Wait, is it really that easy to recover the controllers?
What happened was that I had all parallel cables connected to both controllers except the battery ones and once I plugged the power cable in 1 of them both controllers somehow turned on and after that both controllers bring up error 28.
I checked all MOSFETS, resistors and connections between the phase connectors & MOSFETS and they all seem fine. Also there were no burn marks visible.
@@rafganX strange. best to program both individually. Power always make sure either one is connected at a time or both are connected as I do using a parralel cable THEN connect the battery
@@mkfixitscooters308 It seemed that if I had the data cable connected on both controllers and then connect the power cable to 1 controller (while the battery is connected), it would supply 5 volts (red light comes on) to the controller that didn't have the power cable connected and also trigger the dashboard and somehow mess it all up.
Pleases what are the disadvantages?
Isn't there a way to use the pro dashboard and solely get the speed feedback of only one controller to keep full dashboard functionalities?
sorry for the late reply but we are not sure. We have heard of diodes being used but have never tested. You could run 2 dashes 2 data cables and just link the throtle that would show speeds of each controllers
Is theres a way to remove or cut some wires to make faster the run of my xiaomi scooter?
Do you sell the dashboard connection, I would like to do that but with a external battery beside the 48v monorim batterie is it possible to join to have more autonomy, good job by the way
If you still need one we can do that for you sorry for such a long reply brother
Hello, can you explain with text the two controller connection you have done in the video? Thanks
Connections Motor Phase Inputs External Same From Mainboard On Scooter To Controller Of 2nd Motor To Phase Inputs Externally Same if you connect It will work smoothly
Display - data cable - parallel cable for controllers
Hi, I replaced the control unit on my Xiaomi 365 PRO scooter and it gave me error 35 (mismatched), how do I pair the new control unit? What is the procedure, what to do??
Can you please make the same cable that fits for ninebot MAX controllers(i mean for awd two motherboards)??
Its very easy to make the cable sure.
Is this how you would do it on a ninebot max as well? The drivetrain appears to be wired up the same way
Maybe never tested
Can you make a video about m365 controller upgrade to 72 volt ?
Second this
Is there decoupler for both controllers to one dashboard??
No just the 1 data line and parallel cable
Why you just not connect the hall sensors from the second motor-controller to the dashboard? I think you was confuising the dashboard with both readings. Just make it work like a master/slave
Can you ship to the netherlands
We only sell the parallel data cable sir
@@mkfixitscooters308 i want to buy a ledstrip kit but your website is uk so i don't know if you ship to the netherlands
@@sothatgames1577 We could ship one for you sir please contact us via facebook.
@@mkfixitscooters308 how much the parallel data cable?
Any disadvantage using 1 Parallel battery on 2 controllers rather then 2 separate battery's for each?
Less range and less amps that can be pushed per controller.
@@mkfixitscooters308 genius! Love it mate. Definitely following. Second the other guys comment, would love to see a m365 controller conversion to 72v if you ever find yourself bored haha
@MKFixiscooters please I would like to use your method and I like to know the disadvantage
The disadvantages are that it take some time :)
hi ...Can run contro Xiaomi M365 without dashboard
no brother
how to run 2 battery 2 controller I like to add back my external battery pack
Please check another video we uploaded for more details
why you cant use one controller?
because both motors require a seprate signal
Gracias por hacerme perder 1 chasis de m365 y 2 centralitas. Hize lo mismo y no aceleraba ninguno. Despues, lo puse a 2 pantallas y auk asi se volvia loco y se ponia a 56 un motor y el otro a 40, hasta q como no paso lo q tuvo que pasar. En recta se quemarok los controladores. Y hablo de 2 dias despues de toda la perdia de dinero y tiempo invertido.
Es tu problema por no hacerlo bien, yo tengo las dos montadas como el tio del video y sus otros videos y me va perfecto me pilla 55-60 con dos motores de pro2 y dos controladoras v3
@@Deexoome podrías pasar tu número para hacerlo yo también Aver si me puedes asesorar un poco
Para emparejar las lcd tienes que conectar la señal y la señal del cable verde del conector de la pantalla y entre ellos un diodo
i cant download the files on your website
You may need to download the recommended app
@@mkfixitscooters308 the things is when i go to your website and go to the part thata says m365 awd under to download it says (no file added)
@@tommym7186 we shall look into this sir. Thanks for the update.
@@mkfixitscooters308 yeah i just messaged about this... i didn't see any AWD files. I'd be fine flashing separately, but I'd like to know the settings on each motor based on your experience
No recomiendo este video a nadie no funciona como debe
Sorry sir we didn't get you