Install a spigot on the side that you can connect a hose to it will make ut easier to drain until most of the liquid is out making it lighter and easier to ti handle the remaining weight. I have done this mtself.
Way to test them for metals: heat small chunk red-hot in torch flame. Momentarily cut off gas flow to extinguish torch. Start gas flow again but do not light torch. Point at still hot chunk. If the chunk continues to glow, it still has precious metals in it.
If you're worried about pressure in the barrel, you need a simple airlock. Unless that cap is a very loose fit, it can easily get stuck, and a with barrels that size, it doesn't take that much pressure to make them burst.
Hey man I cut a lot of hardened steel in industrial settings and what I've found is the best blades for my grinders are Bluefire from Norton Abrasives by far. They're also cheaper than the rest I've used over the years. Haven't broken a single one yet either *knock on steel* As an example, cutting 1" hardened steel bolts out of concrete factory floors. I had to cut 60 of them on a task and my DeWalts lasted about 2 bolts each. After eating 4 of them I ordered Bluefires and used a single disc to cut the rest out, cut every job for the next month, and the disc is still good, only missing about half an inch.
Someone learned their lesson and dumped the shock in without the lid on... put a bulkhead fitting on the bottom side of your leaching barrel. To much risk trying to dump the barrel into the filter. A $20 part will save spills, lost money and your health.
I think you should use distilled water and flush your sludge a few more times . You're wasting a lot of metals there . Other than that I love your process .
Do u think the coating on one side.of that store foil will do something unexpected maybe why it won't clear up? Maybe next time try to find the kind without the coating
Aluminum foil doesn't have a coating - one side is shiny because it is rolled out two sheets at a time, with the outsides staying shiny and the insides that touch the other sheet of aluminum getting dull. That said, aluminum can cause solutions to be difficult to filter if the pH or concentration is too high, causing aluminate gels to form.
how are you friend you have a lot of experience in extracting gold and precious metals i also want to learn something from you. i want to know if it only palladium is nitric acid (HN03) in Dissolution or not
I grew up working in junkyards and when I was we used to hollow out Catalytic converters with a long screwdriver and a hammer. Nowadays I see people spending so much time cutting them open? I can clear one out completely in a minute or so. Is there a reason I don't know about why you spend so much time cutting them open? Just curious is all. I enjoy your videos thanks
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
Your t-shirts crack me up, no1 crazy backyard scientist!
Thanks 👍
Install a spigot on the side that you can connect a hose to it will make ut easier to drain until most of the liquid is out making it lighter and easier to ti handle the remaining weight. I have done this mtself.
Way to test them for metals: heat small chunk red-hot in torch flame. Momentarily cut off gas flow to extinguish torch. Start gas flow again but do not light torch. Point at still hot chunk. If the chunk continues to glow, it still has precious metals in it.
If you're worried about pressure in the barrel, you need a simple airlock. Unless that cap is a very loose fit, it can easily get stuck, and a with barrels that size, it doesn't take that much pressure to make them burst.
I would appreciate it if you write the name on the bag what you put in this barrel, thank you
You might be able to dissolve away the magnetic metal substrate with sulfuric acid, and leave the PGMs behind to filter out.
Hey man I cut a lot of hardened steel in industrial settings and what I've found is the best blades for my grinders are Bluefire from Norton Abrasives by far. They're also cheaper than the rest I've used over the years. Haven't broken a single one yet either *knock on steel* As an example, cutting 1" hardened steel bolts out of concrete factory floors. I had to cut 60 of them on a task and my DeWalts lasted about 2 bolts each. After eating 4 of them I ordered Bluefires and used a single disc to cut the rest out, cut every job for the next month, and the disc is still good, only missing about half an inch.
Awesome thanks
Love the safety sandals
Nice video sir next part
Someone learned their lesson and dumped the shock in without the lid on... put a bulkhead fitting on the bottom side of your leaching barrel. To much risk trying to dump the barrel into the filter. A $20 part will save spills, lost money and your health.
Does it matter if it's a rubber or metal barrel?
@@DoWutNow hell yes, metal will dissolve.
The PMs are on the outside of the ceramic honeycomb. Crushing is not needed.
Using thicker aluminum will make your PGMs fall in larger clumps. Making settling and separating it 100xs easier
Awesome. Thanks for the advice!
The adding of the acid after the aluminum only dissolves your PGMs again, it doesn't create or drop more PGMs
Siphon trick was nice
Is the extracted platinum jewelry grade or is more processing required?
I think you should use distilled water and flush your sludge a few more times . You're wasting a lot of metals there . Other than that I love your process .
How much calcium hypochlite do you use through the process ? And how many times you feed into the barrel, every day ?
Thank you
I only did it twice in the whole 2 months. Only about a quarter of the bag 👍
Very cool!!! Great video!!! Thank you 😊 door noob insides are made zinc you can find it everywhere in your travels for the next time
Hello, is it convenient to do that, do I make a profit? I'm from Argentina
What is the name of powered to be added.
Those whiter ones from eBay had been washed already.
Always keep your material damp as the majority of your valuable materials are light and will float away
Do u get paid more if u refine the converters yourself
No. I just like getting out the platinum 👍
When the second vidéos boss ?
Will be very shortly👍
Do u think the coating on one side.of that store foil will do something unexpected maybe why it won't clear up? Maybe next time try to find the kind without the coating
Aluminum foil doesn't have a coating - one side is shiny because it is rolled out two sheets at a time, with the outsides staying shiny and the insides that touch the other sheet of aluminum getting dull. That said, aluminum can cause solutions to be difficult to filter if the pH or concentration is too high, causing aluminate gels to form.
I want to come to you and learn how to recover metal from silencer converter, will you please teach me
Diamond blade chop saw to cut. Refineries use pneumatics, but that's above our paygrade😅
how are you friend you have a lot of experience in extracting gold and precious metals i also want to learn something from you. i want to know if it only palladium is nitric acid (HN03) in Dissolution or not
Yes, nitric acid will dissolve palladium (and even some platinum depending on the alloy composition).
Never handle this stuff dry. Every puff of dust is values lost
I grew up working in junkyards and when I was we used to hollow out Catalytic converters with a long screwdriver and a hammer. Nowadays I see people spending so much time cutting them open? I can clear one out completely in a minute or so. Is there a reason I don't know about why you spend so much time cutting them open? Just curious is all. I enjoy your videos thanks
Big long masonry drill bit and buzz it out. Makes a hell of a mess though.
Campuran apa sajakah untuk mengambil paladium nya?
Tolong sebutkan,terimakasih
Where is the part 2 please
It will be coming in a couple weeks. Sorry for the delay. I had to leave town again for a couple weeks.
@@jandlcrafting1332 ok boss no worries 🙏
Nice vid
Bruder mit Eisen İst ya gunstiger warum halb Alu ?
When you apply to much water you cant precipetate it, in this case you need to evaporate the water to concentrated.
after adding aluminum foil the salts will cement out of solution becoming metal, you refer to the cemented material as salt probably by mistake
Hi sir first video use chemical sodium chlorite and sodium hypochlorite please tell me sir
Run the part 2
Drill a hole in the button so u don't have to tip it
Part 2 please
I hope dude hasn't got ill from platinosis or something, next video is taking a while
Ban viế lên từng loại hóa chất loại nào vào chước noại lào vào sau quy trình từ đấu đến núc song hộ mình có được o vì mình o hiểu ban nói csi rì cả
Hi sir next part please
Coming soon👍
Use a tile cutting saw disk
Mr White type shit. 👍🏽
Bạn làm một hài làm ba li um từ bắt đâu hộ mình có đươc o cho mình sin
İch habe mein eigene art und Deins gemischt danke wolte ich sagen
Hi sir next video upload please sir