Front suspension lower arm replacement
HTML-код
- Опубликовано: 15 мар 2016
- How to replace a front suspension lower arm on Peugeot 206. Step by step. lower arm ball joint silent block.
This video does not constitute or replace a real specialized technical manual, and was only made for convenience and educational purposes. "TutoBuild Eng" makes no warranties of any kind and accepts no liability. "TutoBuild Eng" cannot be held responsible for any damage caused to devices or persons using information contained in this video. The use of the information contained in this video is at your own risk. 
Авто/Мото
Tip - Leave the nut on before you hit the bolt to free it = It will save on damaging the thread
10/10 -Thanks for the great instruction guide ,was very helpful!
Using a bit of pressure from a trolley jack underneath a tie rod when it's spinning is a bit easier than using a clamp! Great video though!
Thanks for a very informative instruction video. You just saved me a huge labour charge. ;-) and I'm not a mechanic at all.
Most people especially women think guys have the natural trait of being mechanically inclined.
muito bom tirou minha duvida. ontem apanhei pra trocar um lado mas nesse video vc mostrou que nao é tao difícil assim. Hoje mesmo vou trocar o outro lado. thank you very much
before tightening the screws of the new arm it‘s recommended to use a hydraulic jack underneath the brake rotor and lift the wheelhub to the neutral position, which can be determined ahead of time, while the wheel is still on, by measuring the distance of the wheelcenter to the fenderframing of the wheelhouse. Tightening in neutral will make the bearings relax most of the time when the suspension is in neutral and thus minimize wear.
The voiceover recommended torquing the bolts up when the the wheel was on, but thats not what he did. Thank's for explaining why its important.
@@imnotamechanic3491 ah, OK. resting the car on it's wheels before torquing the bolts is also an alternative. However often not as convenient😀
And hitting the ball joint with Metal hammer is also not good.
great job mate. I done the same. Bit of tap as well. Brand new the kant..
great video that answered my questions. Cheers
Melhor vídeo,melhor filmagem melhor explicação
I can highly recommend using a lashing and jacking up the wheel hub if you want to get the ball joint back into the lower arm. It pulls the shock absorber back in place and reduces the angle of the ball joint to the lower arm. Otherwise you can be busy for hours and hours, getting absolutely nowhere. It looks so simple on the video, but I just finished the job, took me 2 days fighting with the lower arm before it was back in place. Finally the lashing got it done in 10 min.
I've just started this, and I've had to stop because I ended up with the shock pulling away from the body of the car, which pulled the driveshaft out of the gearbox and has dumped it's oil.
Spot on advice, small set of spring compressors on the strut to take up the excess extension of the strut makes it easier to replace the ball joint and prevents the drive shaft from being pulled out of the gearbox .... (in my limited experience)..
It is very straightforward on the R/H side as the driveshaft has an intermediate bearing which prevents the shaft from falling out of the gearbox, I learned the hard way (on the L/H side) like CableWrestler !
Nightmare of a job lol, I am doing it now, getting the lower ball joint together is no fun at all.
You the best!!!!my peugeot needs it!!!!
Excellent video , thank you !
Very helpful thank you
THANKS BROTHER Good job
Thank you!!
Great really helpful
Very nice your vídeo!!
Very good!
Good video. Thanks for sharing !
Muito bom, resolvi meu problema, obrigado ☺️
Very good video :) how much NM you use for the wheel bolts?
Very good video thank you
My mechanic said the lower arm is broken. I also feel my riding comfort reduced a bit. So, is that because of the lower arm? I was told to change the entire suspension though. Thanks!
Muito bom o vídeo, bem detalhado .
very good well presented,, i now know what to do thaanks
Bit of assembly grease wouldn't go amiss.
Very good..
hallo there! can i raise my peugeot 307 sw 2007 diesel some cantimeters with longer springs?? or can i put some spacers at suspension rear and front?? i want moore ground clearence...
How hard the original bolts are? Class 8.8, or higher for this 206?
Hi, great video
Can you tell me which torque, in each bundle
thank you very much for your attention
Best Regards.
the 2 chassis bolts are 103lb/ft and ball joint 30lb/ft or 140nm and 40nm
Tava apanhando para trocar do meu mais esse vídeo mostra uma maneira fácil e eficaz de fazer
Estou apanhando pra encaixar o pivô no local.
Soltei o encaixe do câmbio.onde você roda e movimenta motor
Great video, have changed one before but this time my drive shaft has dropped out, it will slide back in but everytime I put pressure on the control arm to get the ball joint in it comes out again, what have done wrong, have been struggling now for days and now losing hope. Help.
Where did you get those massive opening Mull Grips? Nice vid btw
Hi, could you please tell me what kind of torx you are using (E?) Thanky you very much!
Andrew Snowden e16 bro.
Masterful stuff.
What w pain in the ass this job is.
My mot on my Peugeot 208 2014, said advisories: Suspension arm pin, or bush worn nearside front, so i took it in to be repaired, and on invoice says product suspension arm, and labour to replace n.s lower arm, no mention of arm pin or bush ? does that mean they not fix arm pin or bush ? thx
Nice men
remove the ball joint after you've done the bolts on the wishbone,swivel the wishbone round then use a hammer on the wishbone to get it out the ball joint 😃
What was the reason to change.
Was that front wheel displaced backwards +
Você está sofrendo atoa amigo ao tirar a bandeja, é só soltar os 2 parafusos do agregado vlw
05:15 this is great.
Will the wheels need re alignment after this
Yes
Hello, can you tell me the Torque to adjust the suspension Arm? Thanks
Échange amortisseur avant Peugeot 206
Good mechanic
This has to be a comedy
Darath Ny hahaha..Thats exactly what im trying to type on the comments earlier..
I'm by no means mechanic so forgive my ignorance where can I get one of those metal bars you are using for leverage on the lower arm?
just use any strong piece of steel, I used to have a 4ft pole flattened at one end makes it so much easier. The one he used for getting the ball joint off is called a ball joint slitter and you use it by aligning the shaft between the 2 prongs and hitting it with a hammer not as a lever like in the video. However after watching again I believe he uses it like that so he doesnt destroy the ball joint dust cover www.ebay.co.uk/itm/12-Fork-Car-Ball-Joint-Seperator-Separator-Splitter-Tool-Tie-Rod-End-Lifter-/222404326887?hash=item33c854b5e7:g:E8cAAOSwh2xYAkly
i swear thats an e60 m5 v10 i hear in the background at 6:30
Anybody no what torque specs the crimp bolt on the lower wishbone joint is
Parte se encaixar o pivô estou quebrando a cabeça
nunca pegar la rotula con masita por arriba vas a dañar la rochca
Wat een monteur
Meri car i10 ka suspension kiase sahi hoga
do not hammer the bolts!
What a brute !
мне понравилось!
Tendrás que engrasar los tornillos antes de ponerlos
Are you a professional mechanic or a DIYer. Reason I ask is that you have just about damaged every thread you had to undo. Ever heard of using a softer material than you are impacting ??? also that is a ball joint splitter not a pry bar so why not learn how to use the tools. Your knowledge of what to do is accurate but if you are typical of what we pay garages £60 per hour labour for in local garages then god knows what we are training our apprentices this day and age.
I am inclined to agree, as even refitting a nut to a threaded shaft provides some protection to the thread before hitting with a hammer. Otherwise, a nice video and a decent repair.
I was about to write the exact same thing then noticed your post. It can be replaced without removing the tie rod too. If you notice before he takes the ball joint off there is a metal ball joint dust cover which im guessing is why he levered it off
if you pay $60 per hours someone to do this youre getting mugged lad xDDD
This guy makes an easy job look hard, wouldn't want him within 10 miles of my car!
No es mejor quitar primero la transmisión??
Никогда рулевые тяги, не откручивайте пистолетом,, она уже не годная, если вы проворачивали ее..
Why was there a need to replace it?
+Márcio R. Hi as seen in the video 4:36 this part has a rubber cone ring on one point and middle so as rubber covered container on other point where thick oil is stored, with time passing oil gets dry and so as rubber and get tiff(might crack brake come loose and boom)....You do maintenance in order to everything function as it should.
Welcome
+Wurth ok thanks
Don't hammering on balljoint
This is what car... Because is hard to change this
Ok
i'm not being cheeky... your using that ball joint splitter wrong,a leg of the fork goes each side of the ball joint,then lever it down
Peugeot 207?
1300 rupee it broke bcoz of jerk
y tampoco la rotula del prazo no pegarla con masita ...la rotula tiene un rio bajarla un poco y entrando solo con mano ..sin masita ....tu no es micanico falta aprender
That's not how you use a ball joint seperator
desgracie se alza tutto anteriore mona
Good apart from the shit globalist ads! 🤬
These Peugeot 206, have the worst lower arm I ever seen. I am a Mechaniker and i can tell you if you are a DIYer don't start with this, cause you will end up with the drive shaft been pulled out from the gear box and the the oil from the gear box comes out. This is a very bad lower arm with too much pressure on it's bearings.
Won't happen on the right side, on the left side it does idd. I found out the hard way.
Yes, you are correct, I had the same unhappy experience a year ago. The driveshaft design is different on the R/H side and has an intermediate bearing which prevents it from ejecting from the gearbox when separated from the stub axle.The L/H driveshaft is one-piece and can fall straight out from the gearbox when released from the hub.
Sorry, but painful to watch some of this. When your trying to get the ball-joint out just tap a small cold chisel or screwdriver in the slot.
You aren't perfesonal
I've never seen such an aberration in all my life. Hits the end of the pinch bolt with a hammer after REMOVING the nut entirely. Then uses a short ball joint splitter as a lever to try to pull the joint shaft out the hub??? And uses no releasing fluid anywhere. Dear god. I've stopped watching at 2:37. Take my advice. Do not use this video as a guide to anything resembling a proper job.
Using a bit of pressure from a trolley jack underneath a tie rod when it's spinning is a bit easier than using a clamp! Great video though!
Yes, who has locking pliers THAT big?