Yes I did but without PTT , just turn ignition off turn it on and immediately press the brake pedal all the way and hold it until all brake solenoids will do a self test, after release and you should be good to go!
Hello mister, I have 2013 Volvo my left front drive axle abs is locked up the wheel, but its spinning when its up to floor, the rest wheel are spinning what is the problem could be , thanks for assistance 😊
Please assist me with this problem. Got a problem with modulation valve on the diff changed it's still insisting on the right side modulation valve. Got this error mid 136 Sid 12 fmi 14 on a volvo truck. Euro 4 with D13 engine Thank you so much
Its the same way like you removing air line from a quick connector fitting! Make sure you don't have air pressure , press that black o,ring and while holding that I,ring pressed pull out the sensor!
Добрый день. Я поменял брейк сенсор этот и сделали коллибровку но все равно на ходу срабатывает тормоз или hill stat assist после зажигаются все сайны и трак едет без проблем. В чем может быть еще проблема?
Start the truck, leave the air compressor fill the system until it's full! Turn ignition off, press the brake pedal and hold it, turn ignition on while holding brake pedal pressed, wait until your hear all solenoids doing self test around 10-15 sec, after release brake pedal and you should be good!
Hi sir. I have volvo truck 2016. No I have a problem with my airbags. They are going up and down during the driving. Especially when I am going down the hill pressing brake or turn on engine brake but sometimes going without it and going up after sometime. I have changed air dryer, air compressor checked all the leaks, pneumatic level sensor under fifth Still same problem. Can it be because I didn't do calibration for the level sensor or not?
Can this censors also disable the cruise control ? I have ABS/TC Lights on and no cruise control. Thanks for the video
I'm having the same issue, if u got fix, what was the problem.
@@aaj8846 We give up and just left it alone, sorry.
Abs sensor most likely
@@saga2760 Hi. Have you fixed ABS/TCS problem yet?
Did you do brake calibration in PTT after you installed brake switch?
Yes I did but without PTT , just turn ignition off turn it on and immediately press the brake pedal all the way and hold it until all brake solenoids will do a self test, after release and you should be good to go!
Where is your place located bro?
Is this sansor an effect at transbicion?
"Classic" 😍...
What’s the diagnosis computer you use? Do u mind to share a link to buy it?
Thanks for this video .where do you have your shop ?
Tacoma / Washington state
You welcome
What program you using to calibrate?
Hello mister, I have 2013 Volvo my left front drive axle abs is locked up the wheel, but its spinning when its up to floor, the rest wheel are spinning what is the problem could be , thanks for assistance 😊
What do you mean is locked? When you press the brake is locking the wheel?
Pirde precios en la marcha baja precios en el diésel
Please assist me with this problem.
Got a problem with modulation valve on the diff changed it's still insisting on the right side modulation valve.
Got this error mid 136 Sid 12 fmi 14 on a volvo truck. Euro 4 with D13 engine
Thank you so much
can a air leak on this pass through valve cause the ABS and TCH light to come on?
Try to pull the senor out how did you do it???
Its the same way like you removing air line from a quick connector fitting! Make sure you don't have air pressure , press that black o,ring and while holding that I,ring pressed pull out the sensor!
@@valeriumoscalu7580 not sure of which quick connection your speaking of?
Добрый день. Я поменял брейк сенсор этот и сделали коллибровку но все равно на ходу срабатывает тормоз или hill stat assist после зажигаются все сайны и трак едет без проблем. В чем может быть еще проблема?
Починил? Такая же история началась
So you change E1, right ?
Yes
I have issue when u press brake abs light on dash on then release and goes off
How do you calibrate
Just need to replace it then air truck up and hold the brake pedal down for 10 sec ENGINE OFF KEY ON
Thank you sir ❤
How to do calibration ?
Start the truck, leave the air compressor fill the system until it's full! Turn ignition off, press the brake pedal and hold it, turn ignition on while holding brake pedal pressed, wait until your hear all solenoids doing self test around 10-15 sec, after release brake pedal and you should be good!
Sir my truck volvo fh440 model 2018 is problem some time give wrong Truck Brake failure 10 ...O.....15 seconds finish wrong
Problemas con DSN 1045 Volvo d13 2014
What is the error code for this ?
Going thru this stuff myself .. the code is :
Component - ec- advanced abs
Description- miscellaneous, stop lamp switch defective (flash code 12 - 2)
Look up code: SPN 1045
How do you pull the sensor out? You never showed us that part
The same way like you disconnecting every air line from a quick connector fitting!!!
So the problem was wiring issues not the sensor … so why replace the sensor?
What is the part number?
My guage for trailer pressure is completely pegged at over 200 psi and when u turn ignition off it only drops to 150
Bad gauge!
Most probably!
Hi sir. I have volvo truck 2016. No I have a problem with my airbags. They are going up and down during the driving. Especially when I am going down the hill pressing brake or turn on engine brake but sometimes going without it and going up after sometime. I have changed air dryer, air compressor checked all the leaks, pneumatic level sensor under fifth Still same problem. Can it be because I didn't do calibration for the level sensor or not?
How do I konw my break sensor not working
Good
So the problem was wiring not the sensor …so why replace the sensor?
Because the updated wire goes with a new sensor, different conector!
A