Looks good! Just wanted to mention, Air Lift Performance is now recommending placing the manifold higher than the tank to help prevent water from getting into it. I see lots of people getting pressure sensing issues, and it seems like they have their manifolds mounted down low. Anyway, great video and great Z! (I’m about to start building my board for my 3H system in my 2018 Mustang GT.
Thanks for showing the steps!!! been looking for a video that shows the full process and yours showed detailed steps!!! Just one question though, how did you run the line for the rear bags? Did you drill a hole somewhere in the back?
Amazing video and car. Should definitely do the side skirts next. Subscribed and followed you on insta. Btw you didn't post the link to the airlift site
Absolutely beautiful. I think OEM with nice wheels and fitment beats wide body (personal opinion). I love the classy look. How much would an air setup like this cost? Debating BC coilovers or air suspension for my HR
BrokenStatues7 if ur still thinking about it, airlift is having a pretty good Black Friday sale, 25% until December 8th. I might pull the trigger on it.
Wait your from Philadelphia? I'm from Kansas but I'm in Delaware till Thanksgiving then traveling down the east coast of Florida. Would love to see your car in person
Hey nice video man, I was wondering what type of screws of bolt you used to mount down the tank, compressor, and management. Also did you insert the bolts from the bottom or top because I can see your barley have any room under the tank to put a bolt.
Yep! The video seemed like I installed it all in one day but it actually took me 3 days! 1st day was setting up the tanks, compressor and management. 2nd day installing the airlines and electrical. 3rd and final day was installing the bags.
when you installed your bags, did you adjust the collar rings or did you leave them how you received them? Ive heard that you need to adjust them to be able to fully air out but I'm not sure.
it's the Airlift 3P full kit. www.bagriders.com/infiniti-g35-v35-nissan-350z-z33-air-lift-3p-air-ride-kit.html You can enter your car specs and select your options.
@@ikigaidriven I’m not really sure how to install this and I live in NJ and I’m like 40 minutes from philly so I’ll make sure I go to David to help me install it
@@LeeMedia Thanks for the compliment man. Really appreciate it. I'm glad my video will be helping a fellow Z owner out! Btw, your editing is amazing! what video editing software do you use?
Yeah it can get loud especially since the 350z doesn’t have an enclosed trunk. However it stays on for a few seconds until the tank reaches optimal pressure.
Thank you for showing how high and low this goes. I’m getting ready to purchase a G35 or G37 and was looking for someone showing this exactly.
Good luck on your purchase and build
Looks good! Just wanted to mention, Air Lift Performance is now recommending placing the manifold higher than the tank to help prevent water from getting into it. I see lots of people getting pressure sensing issues, and it seems like they have their manifolds mounted down low. Anyway, great video and great Z! (I’m about to start building my board for my 3H system in my 2018 Mustang GT.
Thanks for your support. Let us know how your install goes
do the star lights. its pretty easy I have done them in a 350z before.
super clean bro! I'm gonna go straight for bags for my 10th gen accord, gonna save up hopefully till spring time!
Thanks for the support! The bags are the way to go if you live in a city with bad roads
Put a big NOS sticker on the tank 😂
Werd that would look hilarious!! And bad ass
@@ikigaidriven and paint it blue
fake it til you make it
Thanks for showing the steps!!! been looking for a video that shows the full process and yours showed detailed steps!!! Just one question though, how did you run the line for the rear bags? Did you drill a hole somewhere in the back?
Excellent video on bags setup
You make great vids man, keep grinding
Thanks for the support!
Amazing video and car. Should definitely do the side skirts next. Subscribed and followed you on insta. Btw you didn't post the link to the airlift site
Car looks perfect as is!
Thanks!! Appreciate the support
Lets good for philly!! Subscribed just ordered my kit for a 370Z
That's great, let us know how it turns out. Thanks for your support.
Absolutely beautiful. I think OEM with nice wheels and fitment beats wide body (personal opinion). I love the classy look. How much would an air setup like this cost? Debating BC coilovers or air suspension for my HR
BrokenStatues7 if ur still thinking about it, airlift is having a pretty good Black Friday sale, 25% until December 8th. I might pull the trigger on it.
Killing it man 🔥🔥🔥
Thanks man, appreciate the support!!!
Thx for the amazing vid helps a lot
Thanks for the support!
Wait your from Philadelphia? I'm from Kansas but I'm in Delaware till Thanksgiving then traveling down the east coast of Florida. Would love to see your car in person
Yeah we should definitely meet up
@@ikigaidriven unfortunately already in Florida, and in 2 days I go back to my home state Kansas
Hey nice video man, I was wondering what type of screws of bolt you used to mount down the tank, compressor, and management. Also did you insert the bolts from the bottom or top because I can see your barley have any room under the tank to put a bolt.
Thanks! I used the bolts/screws that came with the kit. And I threaded the nut to the bolt from the bottom of the board
awesome video! what would you say that the max ground clearance would be in cm now? thanks
Depends what setting I have it in
Where can I buy this kit? Want to bag my z33
I love it, good job, clean ass f**k!
Thanks for your support!!
Hey dude, are you running 1/4 or 3/8 lines as love the speed. Thanks
They're the 3/8 lines. Thanks for your support
@@ikigaidriven Thanks dude, getting mine order now!
@@ikigaidriven Would you recommend 2 compressors out of the gate or has one been OK?
That pink wire for the management you ran into the fuel pump fuse would that be the same way to run it instead of splicing into the ignition wire?
Basically, thanks for your support.
Are those 18s wheels? My front bags won't touch the fender lip, they maxed out 2 inches above.
Yup these are 18s
Can you spin the bags to make it lower or it's fixed at that?
Hey can you give me a list from the airbag brand etc please ❤️
A list?
Did you have a problem balancing out with air due to you passed the airlines on One side to do the front bags?
no issues.
looks good bro! what size air tank did you get ? do you have Instagram? I got a couple questions if you don’t mind 😭
thanks! it's a 4 gallon tank. our instagram is @ikigai_driven
that's the way to do it, air line's installed first so you can still drive the car if you didn't finish.
Yep! The video seemed like I installed it all in one day but it actually took me 3 days! 1st day was setting up the tanks, compressor and management. 2nd day installing the airlines and electrical. 3rd and final day was installing the bags.
Is that the stunt spot behind the warehouse on Richmond?
Haha good eye.
Ikigai Driven I’m not sure how I never saw this car. My Z is on my profile.
Beautiful car!
Where did you guys get the other part for the connection that you guys put the fuel pump fuse where can I get it?
AutoZone has it. It's called 'add a fuse'. Make sure to get the right size though. Not sure? Get all and return the one you don't use. Lol
Are u running bags a oem battery?
Battery had been replaced with OEM spec before
Where’s the link to buy one ?
www.bagriders.com/infiniti-g35-v35-nissan-350z-z33-air-lift-3p-air-ride-kit.html
when you installed your bags, did you adjust the collar rings or did you leave them how you received them? Ive heard that you need to adjust them to be able to fully air out but I'm not sure.
I left them the way it did
Next go fbo and tune
Yep, we have big plans for the car. Thanks for the support!!!
Why didn't you want to go back to Air ride?
This is an air ride set up
What size valves. That can’t be 1/4 it’s pretty fast
they're 3/8's
Any way to fix an oil cooler lines?
Can you elaborate? The 350z doesn't come with oil cooler unless getting aftermarket. And there's no oil cooler line when installing air bag setups
@@ikigaidriven oh I'm sure but something is leaking oil in my car, i don't have an oil cooler so I have no idea where it's leaking
But thanks for the insight!
That air line you fed through the grommet did that follow your wiring under the carpet on the passenger side?
Yup I did.
how much did this all cost??
$3,000
Can you give me the links for everything you used please?
it's the Airlift 3P full kit. www.bagriders.com/infiniti-g35-v35-nissan-350z-z33-air-lift-3p-air-ride-kit.html You can enter your car specs and select your options.
@@ikigaidriven thank you so much!!
@@ikigaidriven I’m not really sure how to install this and I live in NJ and I’m like 40 minutes from philly so I’ll make sure I go to David to help me install it
@@vergevision1943 David won't be able to help you out on that. He only let me use his shop for space to work on.
New wheels?
Nope, had it for awhile now
Ikigai Driven haha naw I mean as your next new item for the car
Oh haha, maybe. It definitely needs it after bagging it to complete the look
Ikigai Driven looks great tho regardless, I’ll be going bags by the end of the year and will definitely use your video as a reference!
@@LeeMedia Thanks for the compliment man. Really appreciate it. I'm glad my video will be helping a fellow Z owner out! Btw, your editing is amazing! what video editing software do you use?
is the compressor or whatevers in the trunk loud at all? ⊙﹏⊙∥
Yeah it can get loud especially since the 350z doesn’t have an enclosed trunk. However it stays on for a few seconds until the tank reaches optimal pressure.
That cut job on the wood looks soooo bad wtf have you done.
Thanks for your support.