Appreciate it!!. Unfortunately, one of the amps went into protection. I have been running this amps at .5 ohm. I'm going to start running an amplifier per sub at 1 ohm.
I didn’t watch the video but I can tell you only having 1 set of wires in the amp inputs IS NOT going to support 17k. The amp is going into protect because your starving the amp. You SHOULD have dual inputs installed with a amp that size. 4 pos/4 neg per amp! With only one set of wires your restricting the amp of amperage needed to support the current your trying to draw wired at .5 it’s exhausting your amp putting itself into protect.
I don’t know what your running for lithium but it looks like a good size bank! Love your system bro! Few small tweaks and you’ll be much happier with the amps performance & health. Those are nasty nasty amps! Usually most wiring for large amps support around 300 amps current per run give or take depending on size/length of runs. It’s more common than it should be that there aren’t enough inputs supplied with large amps and forcing you to purchase imputs if your trying to get the full performance the amp. Bass on brother!
@Scott-lu4vj- Im not sure why you would make a comment, since you stated that you didn't watch this video? The 1 set of wires you see, on the left side of the 17ks, are 4 gauge, subwoofer/speaker, output wires👀! These Crescendo 17k amplifiers, have 4- 0/ga. Powers, and 4- 0/ga. Grounds, (PER) amplifier, on the inputs!
I love videos like this, seeing what those amps can do in a real world environment.
Thanks a lot. I have more testing coming up with different amps on the future 🔊🔈🔉👍
Your truck is amazing bro 😎 props major props 12k on full tilt nuts
Appreciate it!!. Unfortunately, one of the amps went into protection. I have been running this amps at .5 ohm. I'm going to start running an amplifier per sub at 1 ohm.
Great video bro!👍👍
Thanks! 👍 🔊🔈🔉
Hey question them FI 18 they are 1 ohm or 2 ohm subwoofer
They are dual 2 ohm. i have a pair of subs per amp @ .5
Ok bro thank a lote man I always does wach your video man
1st
Thanks brother 👍 🔊 🙏
@@956Bassaddictplease do a drive thru bass video🤣🔥
Good idea. I will do a drive thru video in the future 🔊🔉🔈👍
@@956Bassaddict can't wait
I didn’t watch the video but I can tell you only having 1 set of wires in the amp inputs IS NOT going to support 17k. The amp is going into protect because your starving the amp. You SHOULD have dual inputs installed with a amp that size. 4 pos/4 neg per amp! With only one set of wires your restricting the amp of amperage needed to support the current your trying to draw wired at .5 it’s exhausting your amp putting itself into protect.
Copy that. Thanks for the advice 👍 🔊🔉
I don’t know what your running for lithium but it looks like a good size bank! Love your system bro! Few small tweaks and you’ll be much happier with the amps performance & health. Those are nasty nasty amps! Usually most wiring for large amps support around 300 amps current per run give or take depending on size/length of runs. It’s more common than it should be that there aren’t enough inputs supplied with large amps and forcing you to purchase imputs if your trying to get the full performance the amp. Bass on brother!
@Scott-lu4vj i been wanted to do the dual inputs for a long time. It makes sense. Maybe it is one of the reasons the amps are getting hot too fast. 👍
@Scott-lu4vj- Im not sure why you would make a comment, since you stated that you didn't watch this video? The 1 set of wires you see, on the left side of the 17ks, are 4 gauge, subwoofer/speaker, output wires👀! These Crescendo 17k amplifiers, have 4- 0/ga. Powers, and 4- 0/ga. Grounds, (PER) amplifier, on the inputs!
@@evilinside5984 I thought those were imputs, good eye 👁️