Fun fact, if you want to remove your calipers, but not loose the fluid, put a brake stick in to push the pedal down about an inch. This closes off the compensator ports between the master cylinder and the reservoir. think of it as putting your finger over the end of a straw and pulling it out of the glass. Holds the fluid in until you are ready to drain it or put the caliper back on.
I love how nothing is sacred to you! You find a perfect early Caddie and your first instinct is not to preserve it. Your first instinct is to shred it to bits and build a drag/speed warrior. You buy a perfect, low miles truck so you can LS swap it and slam in on the pavement. You build a 55 Chevy with a Chrysler elephant! “Nothing is Sacred” should be your next Tshirt.
You are right that color is amazing! When you said treats to your dog my dog was listening and sat uo and looked at me so I had to get up and give him a treat! 😂 My dogs know the "W" word as well!
I lowered a 1995 2wd ext cab short box. No welding. Did a 4 inch front and a 6 inch rear. Had to cut the notch and drill holes for the brace bracket. I used a kit from DJM Suspension. Worked decently from what I remember. This was years ago.
Bringing Joe on full time was the best decision made for the channel. I do miss Cotton and Newbern tho. I hope they are doing well and we get to see them soon.
Newbern is off doing his own channel, and it is full of vehicles that actually get done and run and stuff (sorry Finnegan, I had to go there). Seriously thought, I do miss how it all went before, but Joe seems to be right on it.
These trucks went crazy. Bought my first one in 21 for my first vehicle. Paid 2000 for a decent truck, rust on frame. Small spots om the box. Otherwise, mint. Now they're selling those truck, same condition for 5k. Wild
Damn these guys are haters complaining about your commercials. At least they aren't talking crap about how much better 12volt daves show is cause it makes them feel better about themselves
Your trucks looks excellent, instead of cutting and buffing it use a clay bar and that will help you take the film off that outside of it. That may also save you a step in the process of getting it ready for SEMA.
Good advice! It’s amazing how well a clay bar improves the surface finish with very little effort & without the risk of burning through that beautiful blue paint!
I've just purchased a 84 short box Ford 150 that has 40yrs of day to day mung on it. After giving it a good wash would claybar help cut through the pollution and just mung or should I use a green scrubby to get the big stuff off first? Trying to save the original paint as much as possible. Just asking an opinion I'm not a paint guy
When these trucks were new, several aftermarket companies offered a bumper with frenched in round fog lights. Likely a Foose-inspired mod back when he worked for Boyd. Looked. really cool & has the effect of reducing the visual appearance of those big flat chrome surface on each side of the license.
Awesome project, love seeing the progress. Personally I'd leave it stock height and get some black NASCAR style rims with a beefy tire and go for the "muscle truck" look with it. But seeings how you are a lowered minitrucker at heart, I totally understand going this route. Can't wait to see the finished product.
I would not repaint it. I would leave it, especially for Sema, highlight the fact that it’s original paint and look what we did with these great cleaning products.
I love my OBS trucks, i have a k1500 and a c1500. Both trucks have less than 100k miles in great condition. I love these trucks. My good friend buys and sells alot of these trucks for 15-20k with lower mileage. They are bringing 2-3x what they were 10-12 years ago.
I leanred to drive in an 1996 ext cab C1500 in that same blue and a bench seat with the 15" chrome wheels. I loved that colour and interior such comfy seats and you could recline the seats all the way back to take a 'nap' in it.
I got my grandparents 92 Chevy G20 starcraft brougham conversion van. It's mint, has 34k original miles, and has the tbi 5.7. I got into an accident, and I am having the hardest time finding parts for it. All while we are moving and looking to buy a 2nd house that we can use for a rental property. I'll eventually find a donor vehicle to strip the parts I need. Nothing has been more stressful than worrying about the van my grandpa ordered in 1991. When my wife and I got the Van. It was at 14k miles.
You can tell you shot in 2 different days your wearing a different shirt on cleaning day then explaining ridetec day..... still love the show mike!!!!!!
Finnegan those front bolt hole's are for a bull bare on the yute. It has had a bull bare on it that's way the lights are gone. My friend. From Brendon Crossley from Gympie QLD on the sunshin cost 4570. Best wishes from a long time watcher in Australia.
Honestly, the truck would look good with just the back leveled to the front or a 1"-3" drop. Perfect truck to make a badass street truck as long as none of the mods aren't reversible. It's honestly to clean and pristine to xo anything to it. Some chevy lover would pay a lot for that truck in its stock form. I would spend a lot of money on a low mile, all stock/original, super clean 99-02 4WD Silverado. I miss my 01 and my 03 so much. My 03 was a 6L RCLB that i was building into a sweet street truck.
Mike I've found as a rule you want about 4.5 inches of clearance as a minimal from the lowest point to clear everything so you may wanna bring it up abit, granted angle of attack and the way the bodywork is rigged up also counts for alot with an overhang, but given how square it is you shouldnt have much trouble and what would be idea might be to give it a joe dirt angle of attack, or do like they did on the dukes of hazard and have the front wheels be an inch smaller than the rears, as they used 14's in the front, 15's on the rear to give it its staggered stance that made it look so good also Jay leno's garage is using some salt of the earth types for their detailing videos, showing how to detail the cars on the cheap, and the guy seems to know his stuff like multiple buckets for the washmit, the clay bar, and the like its the video on the old old porsche, back when they werent overpriced and crappy, like this really beautiful black old machine and you kinda need to foam the car first, to take the dirt off, then rinse, then use the mit, as the soap acts like the remover, and dont use dawn dish detergent which I did on the red one, go figure, 2 years after I sell the car, a car which I owned since new for 12 years, then he tells me worst part is with how sad a shape it was in, I could have actually tried that stuff in that video myself to fix it which is also why I know that 4.5 inch rule, as I came in too fast once, and barely cleared a concrete slab that separated the grass from the parking lot by less than 1 mm, and I have since moved onto a raised version of that same car and god is it nice to not have direct injection of every bump in the road, as I went from a car that had the ride quality of a old sportscar, to a lincon continental mark V in one of the worst places to have a stiff car, and god is it so nice to not have a direct injection of the shocks into my knees I just wish I had the old motor back, as that bitch sounded just like the old rally quattro's when you got on it and consumer reports complained about how loud it was, still cant believe that, me I was like this baby needs a sports exhaust lol 16:20 to 16:44 OHHH so that's what happened to that cuda in the barret jackson video they had on jay lenos garage, the idiot lowered it and broke that on the right side, I knew there was something off about the damn thing, and he said nah they just dont drive that well dumbass broke the thing, a multi million dollar cuda, a car he jacked up the price on so high that no normal person can touch the thing and tell him, hey your car is broke man
A six cylinder regular cab trucks didn't have tow hooks. The holes in the air dam are then obviously cut out for the tow bar that used to be on it. That explains the other holes in the frame being used and the low miles.
W/E... I want Finnegan to get paid. He doesn't make these videos out of the goodness of his heart. He does it to support himself and his family. Want something for nothing? go make a cardboard sign and stand out on a street corner.
@@KYoss68 And I am not going to watch these no longer and his ads are wasted.20 minutes are too much,that is all.Everything is about money these days and who has time to watch one hour long infomercials?
Once clear starts lifting there is no fixing it.. It's one of those things where the only option is to sand it all off and start over because anything you put over it is just going to lift as the dead clear under it lets loose. (I took autobody refinishing in college, was going to be my job until my back ruined all manual labor for me.)
On your lower control arms lower a arms you can move the sock to the outer hole it will make the spring stiffer without changing the rate of the spring you just lose the leverage of the A-frame and also help with your role Center
Decent episode with 2 comments. 1, I'm still waiting to see the secret/easy shortcut for keeping the aluminum strut cup in place while installing the shock. B, the markings/wear spots where the tow hooks USED to be, indicates the truck HAD tow hooks.
The knockouts have been removed so like all GMT400's, the factory alignment was crap and someone knocked it out and did an alignment. By the time this truck was built, the word was out and everyone knew the alignment had to be done early to save the Tiger Paws and get it covered by warranty.
aye finally someone i watch is fucking around with the obs trucks so i can finally learn what to do to mine thanks mike & how can i remove the stupid 95mph limiter ? i swear my 350 wants to keep going 😅 i was just doing my front suspension today, and this helped.
Only thing I would do is exchange the front end for the one that came off the SLT trim and possibly try to find a set of the old school Centerline rims from the 90s
Thanks for making me feel like I must have made it in life - haha....I had 5 of those trucks in the late 90s early 2000s. I may not have thought much of it then but it was before trucks were"cool".
Not that it matters but those aren't fog light holes on the airdam they are where the tow hook petrude through. Also I didn't realize they put tow hooks on 2wd trucks. Maybe it was an extra option?
Great show, as always ! On a more serious note, please wear eye protection when you're working below the truck/any vehicle. You'll miss an eyeball more than you'd think. I know ....
Hey Mike. Rich from Deboss garage used a product from Rust-Oleum called crud cutter to remove rust from a subframe on an EV project on one of his last videos. You might try it on that right front frame. It seemed to work really good on the subframe he was doing.
Said it before I’ll say it again this was better with newburn… you and Dave had the best RUclips videos I still go back and rewatch them even the mail videos with him were good. Now if I watch 20 minutes that’s lucky
Literally used the #BlingSauce ‘this morning. The coconutty trim sauce smell is so nice. The leather sauce is great on leather wrapped steering wheels and shifters, too.
Mike, your the only one that can build a truck for a company for Sema. Where they can't even show off their products and it's still ok! Well it doesn't have leather, and black plastic and rubber trim. But it's in good shape and it has paint! Just put a leather seat and a rubber bumper on the floor of the display. 😂😂😂😂 love it. Thanks bling sauce!!
Hey don't take this the wrong way but everyone has done a obs is some way or another. Now you have a couple builds that bring attention like for instance you have a Sonny big block and custom cage. I am referring to the Cadillac I would take even Blasphemy instead a lowered obs thats played out. 🤘😎🇨🇦
I would love to see you build the v6 with a little boost. Just think, the v6 will take more boost than an LS before you need to change head gaskets. LOL.
One bump away from not having any brakes. The coil spring is gonna cut those brake hoses in half. Hopefully there are stainless braided hoses in the future. Performance brakes and factory rubber brake hoses is a no go.
talk about how they lower everything, next weeks episode with be the gasser Blasphemi with nose in the air like it is the snob in the garage that wants to sniff the cleaner air above the other cars tail pipes. I would say that you lower all the right cars, and sometimes you just have to go against to grain and raise one up.
Hwy Finn , how’s the leg has it been 6 weeks already .. seams like last week you broke your leg after buying that 510 .. and I saw the episode when you got that OBS work truck doing the one leg burnouts .. at your buddy’s new place .. but anyway hope all is well and legs Doing fine .. have yo catch up on your boat motor if you saved it or not .. saw bits and pieces of it but I will get it done and watch it .. ok good luck at sema with the OBS
Man i really don't need a 2x4 SC SB GMT400 up here in Qc, Canada but id love to have it. 😅 im actually shopping for a SC LB 4x4 Stick shift. i bought a Parts truck with clean title and a NV3500 4x4 but its too rough to even fix. im thinking about going down south and get me a solid base to build a nice little worktruck. 👌 i miss my 97 GMT400 own it for 10yrs rust just had to take it from me. 😔
Beautiful dog. It's a fact that 90% of new jeep owners say that it will never go off the pavement, ever. And they have no idea what the term " jeep life" even means.
When I was a young if you seen a truck sitting that low you knew w the springs were wore out me personally I don't won't a truck low on the ground if I want to haul stuff don't have to worry about dragging stuff
Fun fact, if you want to remove your calipers, but not loose the fluid, put a brake stick in to push the pedal down about an inch. This closes off the compensator ports between the master cylinder and the reservoir. think of it as putting your finger over the end of a straw and pulling it out of the glass. Holds the fluid in until you are ready to drain it or put the caliper back on.
I'm going to try this
I use this method at least once a week
Holy hell that's a cool tip. def gonna try it out the next opportunity
I have heard this but I thought it was half way to close off the valve body in the master cylinder.
I love how nothing is sacred to you! You find a perfect early Caddie and your first instinct is not to preserve it. Your first instinct is to shred it to bits and build a drag/speed warrior.
You buy a perfect, low miles truck so you can LS swap it and slam in on the pavement.
You build a 55 Chevy with a Chrysler elephant!
“Nothing is Sacred” should be your next Tshirt.
I was a 20 year old salesman at a GMC store in Tucson when that was a new truck.
Eww Tucson lol. I've been in the 480 for 30 years
@@Berm_Blaster left Tucson in 1997. It was great back then.
You are right that color is amazing! When you said treats to your dog my dog was listening and sat uo and looked at me so I had to get up and give him a treat! 😂 My dogs know the "W" word as well!
I lowered a 1995 2wd ext cab short box. No welding. Did a 4 inch front and a 6 inch rear. Had to cut the notch and drill holes for the brace bracket. I used a kit from DJM Suspension. Worked decently from what I remember. This was years ago.
Bringing Joe on full time was the best decision made for the channel. I do miss Cotton and Newbern tho. I hope they are doing well and we get to see them soon.
Newbern has his own channel www.youtube.com/@12VoltDave but we need more Cotten Fer sure!
@@MC-cy1zi aren’t they doing the faster with newbern
Newbern is off doing his own channel, and it is full of vehicles that actually get done and run and stuff (sorry Finnegan, I had to go there). Seriously thought, I do miss how it all went before, but Joe seems to be right on it.
These trucks went crazy. Bought my first one in 21 for my first vehicle. Paid 2000 for a decent truck, rust on frame. Small spots om the box. Otherwise, mint. Now they're selling those truck, same condition for 5k. Wild
Wow, that's a clean old truck, and you're right. They always look better lowered.
I think that is what Joe was starting to say about how well it was coming apart without heat before… squirrel
Damn these guys are haters complaining about your commercials. At least they aren't talking crap about how much better 12volt daves show is cause it makes them feel better about themselves
Your trucks looks excellent, instead of cutting and buffing it use a clay bar and that will help you take the film off that outside of it. That may also save you a step in the process of getting it ready for SEMA.
Good advice! It’s amazing how well a clay bar improves the surface finish with very little effort & without the risk of burning through that beautiful blue paint!
I've just purchased a 84 short box Ford 150 that has 40yrs of day to day mung on it. After giving it a good wash would claybar help cut through the pollution and just mung or should I use a green scrubby to get the big stuff off first? Trying to save the original paint as much as possible. Just asking an opinion I'm not a paint guy
@@parentsbasement7734 Always clay bar before cutting/polishing.
I love following you you actually show what you are doing and explain what you are doing and why your doing it just amazing
That’s not a fog light bumper, those holes are where the tow hooks come out at. They twist and sit horizontal in those holes.
I know, think he is losing it. Nor do you tie down the frame of a vehicle...lmao
When these trucks were new, several aftermarket companies offered a bumper with frenched in round fog lights. Likely a Foose-inspired mod back when he worked for Boyd. Looked. really cool & has the effect of reducing the visual appearance of those big flat chrome surface on each side of the license.
Awesome project, love seeing the progress.
Personally I'd leave it stock height and get some black NASCAR style rims with a beefy tire and go for the "muscle truck" look with it.
But seeings how you are a lowered minitrucker at heart, I totally understand going this route. Can't wait to see the finished product.
I kind of wanted to watch a show about you working on a truck and ended up watching a show about bling sauce
That's a nice find
I would not repaint it. I would leave it, especially for Sema, highlight the fact that it’s original paint and look what we did with these great cleaning products.
I love my OBS trucks, i have a k1500 and a c1500. Both trucks have less than 100k miles in great condition. I love these trucks. My good friend buys and sells alot of these trucks for 15-20k with lower mileage. They are bringing 2-3x what they were 10-12 years ago.
I leanred to drive in an 1996 ext cab C1500 in that same blue and a bench seat with the 15" chrome wheels. I loved that colour and interior such comfy seats and you could recline the seats all the way back to take a 'nap' in it.
I got my grandparents 92 Chevy G20 starcraft brougham conversion van. It's mint, has 34k original miles, and has the tbi 5.7. I got into an accident, and I am having the hardest time finding parts for it. All while we are moving and looking to buy a 2nd house that we can use for a rental property. I'll eventually find a donor vehicle to strip the parts I need. Nothing has been more stressful than worrying about the van my grandpa ordered in 1991. When my wife and I got the Van. It was at 14k miles.
Love the Indigo Blue paint. Had a 95 SLE fully loaded just like it, but unfortunately she got flooded out in 2014. I wish I could get another one.
You can tell you shot in 2 different days your wearing a different shirt on cleaning day then explaining ridetec day..... still love the show mike!!!!!!
Finnegan those front bolt hole's are for a bull bare on the yute. It has had a bull bare on it that's way the lights are gone. My friend. From Brendon Crossley from Gympie QLD on the sunshin cost 4570. Best wishes from a long time watcher in Australia.
Honestly, the truck would look good with just the back leveled to the front or a 1"-3" drop. Perfect truck to make a badass street truck as long as none of the mods aren't reversible. It's honestly to clean and pristine to xo anything to it. Some chevy lover would pay a lot for that truck in its stock form. I would spend a lot of money on a low mile, all stock/original, super clean 99-02 4WD Silverado. I miss my 01 and my 03 so much. My 03 was a 6L RCLB that i was building into a sweet street truck.
Mike I've found as a rule you want about 4.5 inches of clearance as a minimal from the lowest point to clear everything so you may wanna bring it up abit, granted angle of attack and the way the bodywork is rigged up also counts for alot with an overhang, but given how square it is you shouldnt have much trouble
and what would be idea might be to give it a joe dirt angle of attack, or do like they did on the dukes of hazard and have the front wheels be an inch smaller than the rears, as they used 14's in the front, 15's on the rear to give it its staggered stance that made it look so good
also Jay leno's garage is using some salt of the earth types for their detailing videos, showing how to detail the cars on the cheap, and the guy seems to know his stuff
like multiple buckets for the washmit, the clay bar, and the like
its the video on the old old porsche, back when they werent overpriced and crappy, like this really beautiful black old machine
and you kinda need to foam the car first, to take the dirt off, then rinse, then use the mit, as the soap acts like the remover, and dont use dawn dish detergent
which I did on the red one, go figure, 2 years after I sell the car, a car which I owned since new for 12 years, then he tells me
worst part is with how sad a shape it was in, I could have actually tried that stuff in that video myself to fix it
which is also why I know that 4.5 inch rule, as I came in too fast once, and barely cleared a concrete slab that separated the grass from the parking lot by less than 1 mm, and I have since moved onto a raised version of that same car
and god is it nice to not have direct injection of every bump in the road, as I went from a car that had the ride quality of a old sportscar, to a lincon continental mark V
in one of the worst places to have a stiff car, and god is it so nice to not have a direct injection of the shocks into my knees
I just wish I had the old motor back, as that bitch sounded just like the old rally quattro's when you got on it
and consumer reports complained about how loud it was, still cant believe that, me I was like this baby needs a sports exhaust lol
16:20 to 16:44 OHHH so that's what happened to that cuda in the barret jackson video they had on jay lenos garage, the idiot lowered it and broke that on the right side, I knew there was something off about the damn thing, and he said nah they just dont drive that well
dumbass broke the thing, a multi million dollar cuda, a car he jacked up the price on so high that no normal person can touch the thing and tell him, hey your car is broke man
Damn sketchy jack stand install - 47:37. Glad you survived!!!
Pro tech tip any bolt or nut going inside a frame rail tack weld a peice of fencing wire to it so you dont loose it inside the chassis
I always mount the swaybar in the tow hook bracket. No factory fog lights on a work truck.
A six cylinder regular cab trucks didn't have tow hooks. The holes in the air dam are then obviously cut out for the tow bar that used to be on it. That explains the other holes in the frame being used and the low miles.
100% agree. Everything is better lowered and must have big bass.
that's super clean. love that blue. i just did a 6/8 drop with helper bags on a 88obs long bed regular cab. cruiser/shop truck.
19:36 if you want to skip past the commercials
Thanks,just commented about super long ads.
No kidding! Ridiculous! Take a shot every time he says "sauce".
W/E... I want Finnegan to get paid. He doesn't make these videos out of the goodness of his heart. He does it to support himself and his family. Want something for nothing? go make a cardboard sign and stand out on a street corner.
@@KYoss68 And I am not going to watch these no longer and his ads are wasted.20 minutes are too much,that is all.Everything is about money these days and who has time to watch one hour long infomercials?
11:55 a detailing clay bar might be your friend here.
Once clear starts lifting there is no fixing it.. It's one of those things where the only option is to sand it all off and start over because anything you put over it is just going to lift as the dead clear under it lets loose. (I took autobody refinishing in college, was going to be my job until my back ruined all manual labor for me.)
On your lower control arms lower a arms you can move the sock to the outer hole it will make the spring stiffer without changing the rate of the spring you just lose the leverage of the A-frame and also help with your role Center
Decent episode with 2 comments. 1, I'm still waiting to see the secret/easy shortcut for keeping the aluminum strut cup in place while installing the shock. B, the markings/wear spots where the tow hooks USED to be, indicates the truck HAD tow hooks.
Is that a Christmas wreath on your door my man? Epic.
I never enter to win anything but have made an exception with this. Had to take a shot.
Get u a foam Cannon and a bucket with a grate in bottom. They make everything so much better. I love my foam Cannon
Loving this truck, gonna be a badass build
The frame was probably brushed with a protective coating to fight rust from road salt, or it could be an old rust preventative like lps3
The knockouts have been removed so like all GMT400's, the factory alignment was crap and someone knocked it out and did an alignment. By the time this truck was built, the word was out and everyone knew the alignment had to be done early to save the Tiger Paws and get it covered by warranty.
aye finally someone i watch is fucking around with the obs trucks so i can finally learn what to do to mine thanks mike & how can i remove the stupid 95mph limiter ? i swear my 350 wants to keep going 😅 i was just doing my front suspension today, and this helped.
Only thing I would do is exchange the front end for the one that came off the SLT trim and possibly try to find a set of the old school Centerline rims from the 90s
Hey Finn, I live in Acworth and have a nice set of old school 15 inch 5 spoke Americans that would look great on that truck!
Thanks for making me feel like I must have made it in life - haha....I had 5 of those trucks in the late 90s early 2000s. I may not have thought much of it then but it was before trucks were"cool".
How do you say this 18:05 and not immediately go full Micheal Scott with a "that's what she said"? Unbelievable discipline!! You deserve a medal.
The line at 18:05 is what I tell my wife in the bedroom.
For your 510, Nissan has a new head for your motor, double over cam head. With a 5 speed conversion with a Subaru rear end .
Not that it matters but those aren't fog light holes on the airdam they are where the tow hook petrude through. Also I didn't realize they put tow hooks on 2wd trucks. Maybe it was an extra option?
Great video Mike , thanks for posting
Great show, as always ! On a more serious note, please wear eye protection when you're working below the truck/any vehicle. You'll miss an eyeball more than you'd think. I know ....
Hey Mike. Rich from Deboss garage used a product from Rust-Oleum called crud cutter to remove rust from a subframe on an EV project on one of his last videos. You might try it on that right front frame. It seemed to work really good on the subframe he was doing.
Said it before I’ll say it again this was better with newburn… you and Dave had the best RUclips videos I still go back and rewatch them even the mail videos with him were good. Now if I watch 20 minutes that’s lucky
I agree...Dave good...Joe not so much
Some chassis undercoatings were dealer options. That might be why it was missing coating behind the control arms.
Needs more dog content for my mate watching with me
Literally used the #BlingSauce ‘this morning. The coconutty trim sauce smell is so nice. The leather sauce is great on leather wrapped steering wheels and shifters, too.
Great little boat. I want one just like it
Mike, your the only one that can build a truck for a company for Sema. Where they can't even show off their products and it's still ok! Well it doesn't have leather, and black plastic and rubber trim. But it's in good shape and it has paint! Just put a leather seat and a rubber bumper on the floor of the display. 😂😂😂😂 love it. Thanks bling sauce!!
Love this build!
I feel a truckin tech article jumped out of the magazine and is playing live on my phone.
Dude!!! Great video!! You need to roll the fenders!!! ✌️
The factory fog lights are missing. Those holes were where the fog light brackets were located.
That’s gonna be a great build
I say a newer LV3 , 4.3 swap with some boost . Try keeping as many of the stock under hood parts as possible.
Hey don't take this the wrong way but everyone has done a obs is some way or another. Now you have a couple builds that bring attention like for instance you have a Sonny big block and custom cage. I am referring to the Cadillac I would take even Blasphemy instead a lowered obs thats played out. 🤘😎🇨🇦
Good job Mike! Now you need a monster truck so you and the family can have fun on the weekend 😅😅😅😅
I would love to see you build the v6 with a little boost. Just think, the v6 will take more boost than an LS before you need to change head gaskets. LOL.
I need the stock spindles for my 1994.. Serious. Do you still have them?
The holes that you said are for factory fog lights aren't for factory fog lights there for the tow hooks to come through
One bump away from not having any brakes. The coil spring is gonna cut those brake hoses in half. Hopefully there are stainless braided hoses in the future. Performance brakes and factory rubber brake hoses is a no go.
Hell ya brother.......
When do we get to see the rear install? It looks done at the end outside? Plz don't make us wait till next Sunday.
The black on the front of the chassis rail, was probably aftermarket dealer undercoating
talk about how they lower everything, next weeks episode with be the gasser Blasphemi with nose in the air like it is the snob in the garage that wants to sniff the cleaner air above the other cars tail pipes.
I would say that you lower all the right cars, and sometimes you just have to go against to grain and raise one up.
Looks so good with stock wheels
Try finishing the Cadillac, that would be cool! Take it to Sema!
Hwy Finn , how’s the leg has it been 6 weeks already .. seams like last week you broke your leg after buying that 510 .. and I saw the episode when you got that OBS work truck doing the one leg burnouts .. at your buddy’s new place .. but anyway hope all is well and legs Doing fine .. have yo catch up on your boat motor if you saved it or not .. saw bits and pieces of it but I will get it done and watch it .. ok good luck at sema with the OBS
Fin we need a car cover company to send you some for the storage of all your ridea
Hi from Australia
These videos have become one long commercial
Please finish the caddy. I've been waiting. Maybe have someone finish it for you?
The holes in the air dam are for the tow hooks, not fog lights. The air dam without tow hooks would look 1000% better.
Man i really don't need a 2x4 SC SB GMT400 up here in Qc, Canada but id love to have it. 😅 im actually shopping for a SC LB 4x4 Stick shift. i bought a Parts truck with clean title and a NV3500 4x4 but its too rough to even fix. im thinking about going down south and get me a solid base to build a nice little worktruck. 👌 i miss my 97 GMT400 own it for 10yrs rust just had to take it from me. 😔
I can tell you that I already know that I won't make it to any other event this year. SEMA is out of the question.
Hell yeah my brother 🔥 🙌 💪
Finish the Cady!!!!!!!
Beautiful dog. It's a fact that 90% of new jeep owners say that it will never go off the pavement, ever. And they have no idea what the term " jeep life" even means.
Awwhhh, maaannn!?!? Why not get those OEM 5 spoke wheels widened? That would be so cool.
Great video, Who makes a good wrench to adjust the collar on the coil over. The one that came with my kit is useless. Slips off doesn't fit well .😁👍👍
20" Torque Thrust 2's would be perfect.
Do the ridetech coilovers let you select different spring rates?
When it comes to saving unsprung weight, pounds makes a huge difference to handling. 20 pounds is Huge!
Even Dennis Collins would be impressed with 19mins of ads!!!
When I was a young if you seen a truck sitting that low you knew w the springs were wore out me personally I don't won't a truck low on the ground if I want to haul stuff don't have to worry about dragging stuff
Wonder what the Datsun will look like when I use Bling Sauce on it?
So how much of this 59 minute video is ads? 1:01 minutes?
Hey, I need those front end parts you took off for my ‘97😂 I’m close by too in C’ville
wonder if that coating on the frame is the undercoating sold by the dealership?
These trucks didn’t come with factory fog lights. Those openings are for the tow hooks.
Four way, all stop, rolls it.
That blue is my tee nice !
NEED TO THROW A TURBO ON THE VORTEC V6