@@ViCatRC Wack in a Dumbo RC combo mate...get the X6FG RX and set Gyro to around 20%. Zero Lag...400m range. straight as a bullet. Top Video, well done man.
hello friend, if I use a 27t pinion in the 124017 v2 the engine will have the strength to push more final speed, since the 124017 is heavier than the 144010, have you tried this set at 1:12?
Hi mate thanks for watching. Honestly I did not expect to go so fast with 144010, stock motor 4200kv and 27t pinion. I expected cogging, but indeed I did not experience. 124017 is heavier and with the v1 motor 3400kv there was lot of cogging. Theoretically with a 4200 kv motor it should be much worse, but I didn't try with this model so I can't ensure it will work. I am not pretty confident it will, but you could try, being carefull not to overheat motor and esc. Just for speed runs probably you won't experience such evident cogging, but on bashing no way, don't do that.
Hello, you just need to heat it with fire, such as a gas lighter. The loctite is pretty much and hard, so you need to heat a lot and turn the screw driver both direction to loosen the screw until it gets unstuck.
Yes mate exactly. The original 144010 motor mounts has the holes for 19t stock pinion and 27t option pinion for a 2845 size motor. Just watch the picture in the intro of the video and match your motor mount. It should have the same holes geometry.
you can find the stl files for 3d printing the 124017/19 144001/010 speed run kit in the link below: cults3d.com/en/3d-model/various/wltoys-124017-speed-run-kit
@@bengilbert31 Thanks a lot Ben, I apprechate it. I am still testing the bottom of the front wing profile to create more downforce at higher speed. No back flipping so far, but I need to push further (80+ mph). I think I will release it in the next days if it gives me good results. You can check on: cults3d.com/en/users/ViCatRC/creations
Hi mate, with this setup you can run a couple of consecutive rips, then you need to cool down the motor. For sure, this setup it's suited just for speed runs. Not suggested at all for bashing.
Nice, thanks for sharing Sir👍
Hey hi !! Thanks for all these clarifications and details 👍🏾👍🏾💯!!
ITS DONKEY TIME 🍆🫵🏿😡
These really are a great deal for the money. I just bought a new one with 2 LiPo’s for $53.
Absolutely. This is actually my favourite wltoys car. Such a shame for the boring throttle delay otherwise it would have been perfect.
@@ViCatRC back it up when you turn on the control,the problem ends.
@@ViCatRC Wack in a Dumbo RC combo mate...get the X6FG RX and set Gyro to around 20%. Zero Lag...400m range. straight as a bullet.
Top Video, well done man.
Hey question what motor mount will fit the 27 pinion please because I don't think they hve the specific one u showed in your video ..
Awesome vid! Just bought this RC car. Can you share a link for the 27T pinion part? Thanks!
Burn up your engine battery boy
Great video! I would like to know how much faster would it be on foam tires?
Thanks for watching. I guess with foam tires it would be more stable but top speed would be lower due to the smaller diameter of tires.
Pin 3s mua ở đâu vậy dòng xả bao nhiều
hello friend, if I use a 27t pinion in the 124017 v2 the engine will have the strength to push more final speed, since the 124017 is heavier than the 144010, have you tried this set at 1:12?
Hi mate thanks for watching. Honestly I did not expect to go so fast with 144010, stock motor 4200kv and 27t pinion. I expected cogging, but indeed I did not experience. 124017 is heavier and with the v1 motor 3400kv there was lot of cogging. Theoretically with a 4200 kv motor it should be much worse, but I didn't try with this model so I can't ensure it will work. I am not pretty confident it will, but you could try, being carefull not to overheat motor and esc. Just for speed runs probably you won't experience such evident cogging, but on bashing no way, don't do that.
The grub screw is very tight on the original pinion. How’d you get it removed?
Hello, you just need to heat it with fire, such as a gas lighter. The loctite is pretty much and hard, so you need to heat a lot and turn the screw driver both direction to loosen the screw until it gets unstuck.
I need those spoilers. Link, please.
cults3d.com/en/design-collections/ViCatRC/wltoys-124017-124019-144010
@@ViCatRC I assume they're better printed in PETG, aren't they?
@eddiespectral I normally print in PLA but the front spoiler is even possible to print in tpu.
What do you mean the original motor mount ? 144010 mount ?
Yes mate exactly. The original 144010 motor mounts has the holes for 19t stock pinion and 27t option pinion for a 2845 size motor. Just watch the picture in the intro of the video and match your motor mount. It should have the same holes geometry.
@@ViCatRC thanks
Any idea where I could find the exact 27t ?
Sorry mate, I just removed it from my old 124017 v1. Depending on where you live there are some options like amazon, bangood, aliexpress.
So the 124017 motor mount can work right
The stock gear, is it plastic or metal?
Plastic.
@@ViCatRC Thank you
Where did you buy his yellow nose?
Hello mate, thanks for watching. You can find the 3d printed part at this link:
cults3d.com/en/3d-model/various/wltoys-124017-speed-run-kit
What is the discharge current of 2s lipo battery??
The stock 2200ma 2s lipo should be around 25C.
能问下你的尾翼用的哪款么？我的尾翼都摔烂了
The front/rear wings I self designed and 3d printed.
hi bud will i need a bigger motor for 27t or i can use stock based on the mounts ?
Thanks mate and sorry for the delay. With stock 4300kv motor you could experience some cogging even if I didn't.
I bought a 5900kv motor for 18 bucks . I hit 77 mph now
What pinion module?
Stock motor 4300kv and 27t pinion. Just for speed runs. Not suggested for bashing.
I would like to buy one of those front aero parts. Where can i buy from?
you can find the stl files for 3d printing the 124017/19 144001/010 speed run kit in the link below:
cults3d.com/en/3d-model/various/wltoys-124017-speed-run-kit
@@ViCatRC oh I dont have a 3d printer thanks tho
Hi m8 what wings are they and where did you get them please
Thanks for watching Ben. Front and rear wings I just designed and 3d printed by myself.
@@ViCatRC OK thanks m8 new subscriber here have you got the files available and would you mind sharing please
Cheers
@@bengilbert31 Thanks a lot Ben, I apprechate it. I am still testing the bottom of the front wing profile to create more downforce at higher speed. No back flipping so far, but I need to push further (80+ mph). I think I will release it in the next days if it gives me good results. You can check on: cults3d.com/en/users/ViCatRC/creations
@@ViCatRC thanks m8
Can it overheat your motor?
Hi mate, with this setup you can run a couple of consecutive rips, then you need to cool down the motor. For sure, this setup it's suited just for speed runs. Not suggested at all for bashing.
@@ViCatRC gotcha