Tips On Troubleshooting Scooter / Motorcycle Engine Noises
HTML-код
- Опубликовано: 6 июн 2019
- Chinese Scooter Service Manual amzn.to/2LBfWb8
Subscribe to my youtube channel bit.ly/2Rcxr41
Donate to Virberello for Parts rb.gy/gzrtit
Tips On Troubleshooting GY6 Scooter / Motorcycle Noises
Being a good listener will ensure that you are able to hear any funny voices that you scooter makes. These may be when riding your scooter and you wonder what could be wrong with your scooter. Odd new sounds, voices and vibrations from your scooter are a signal that something is probably wrong with your scooter.
In most cases these funny noises and sounds are usually a warning. With any scooter types, the sources of these sounds and noises can be both unusual and routine, but others may be distinctive warning of specific scooter problems. The common rattle from your scooter can be a loose external component and that just needs some tightening up or buying a new fastener. Below are 2 of these sounds and noises on your scooter and what they may mean for your scooter.
Snap, crackle, pop
This sound may indicate a “short “or a leakage of the ignition energy to the ground. This is most likely to be especially if it is accompanied by a hesitation of the engine. This sound may be caused by the ignition energy that are arcing from a flaw or a crack in the spark plugs wire insulations, the caps of the spark plugs to the engine, frame or other metallic components. Carefully inspect whether the wires and the caps are in perfect order. The costs of these components are low and you should replace them when you have doubts.
Boo, hiss sound
This sound eliminates from deflated tires. The ability to hear your tires going down simply means that you stop the situation from becoming a potential crash. Flooded cell battery on the charger or the charging system which is seriously overcharged causes the electrolytes to off. The gas can cause a hissing sound since the gas if being forced out from the overflow tube, out of a crack on the case or out of the cell cap. You should stop immediately this charging condition will help protect you from a potential battery burst.
Some other sources that may produce this hissing sound may include radiator leaks, blown gaskets and exhaust system that is leaking. These sounds cannot disable your scooter immediately but they signal the need for service of your scooter very soon.
These are just but two sounds and noise that you should look out for in your scooter as you ride it. The sounds and noises your scooter can create are unlimited. Being familiar with your scooter will ensure that you know the sounds it produces normally and which are not.
I hope this video will help you
If you have any question feel free to ask
Chinese scooters, gy6 motors, vespa, motorcycle 
Хобби
I've replaced the drive belt, troubleshooted electrical leaks, replaced hoses, fuel filter, carburetor and on and on. All from watching your videos. Keep them coming. I don't know what might break next 😉
Thanks a lot,
Paul
Hello Paul Thank you for watching my videos
Scooter was making a “dook dook dook........dook dook dook” sound, could sort of feel it when Idle/riding, turns out it was the belt missing a few teeth.
Thanks for the vid
You are a life saver Hermano !! Best scooter channel on RUclips
Hello my friend thank you for watching my video
I like the noises you made. They sound very realistic and are very helpful. Thank you.
Glad you like them!
Great video! I love the tip about amplifying sound with the screwdriver.
Hello my friend thank you for watching my video
these videos are so useful. thank you for taking the time to make them
Thank you for watching my video
Great job.
Great video thank you!!
Hello Stikmannn thank you for watching my video
Thank you 4 ur words I've fix my bike 4 watching ur videos bud very helpful
Hello my friend thank you for watching my video
as always it is very informative, thanks a lot
Hello my friend thank you for watching my video
Thanks I learned alot an took note and will tackling my scooter tomorrow
Hello my friend thank you for watching my video
Great tytorial. A question.. on my 250ie scooter ( Piaggio quasar engine with 30.000kms life) it ìmake a strange noise, in torque when I realease the throttle it make a metal noise like sometingh metal is slippering on metal just for a second and stop.. ( in the same time I have a clutch noise..
Thank you
Hello my friend thank you for watching my video
Great video bro thanks
Thank you for watching my video
Wow lot of info thanx !!!
Glad it was helpful!
You look dapper in a suit...
very nice advise
Hello Luzia thank you for watching my video
My Vespa S ("SICK") 150 CC(2021) Made in India version variator roller makes a rattling noise when the accelerator is given .I replaced the whole variator assembly and the rollers too and still it makes such weird rattling noise .Do you have any solutions to solve it?. Please leave a comment.
You are a very clever man.
Hello my friend thank you for watching my video
Did you go to a funeral for your scooter my friend ? Lol !!!!
Ah Ah Ah You funny my friend I work for a funeral home part time ah ah ah Thank you for watching my video
Perfect video
Hello my friend thank you for watching my video
U missed the chain tensioner and chain plate noise ... nice video
I just had to learn how to replace my starter gear. It was making a loud grinding sound at idle and low speeds. I also ruined my stator in the process of removing the flywheel. All in all a 2 week no riding learning experience. Great video!
Hello Ronald Thank you for watching my video
What's a starter gear ? Is it also called an benix
@@bbrown9216 On a 2 stroke you have a bendix. 4 strokes have a starter gear.
I'm having the same problem on my moped at low speeds, sounds like something is grinding/scraping and I can't find anything online on how to fix it.
Grazie paisano mio! Me piace molto!
Grazie mille Jimmy e felice anno nuovo
My Xmax 125 make click sound when I accelerate it from 15 Mph to uppe3 like If you use full throttle from 15 mph to more its make single click sound. Do you have any idea why? Local mechanisc said its norhing.
Can you advice
Hi, great video smart guy. Just got my scooter back from mechanics and they replaced the battery and had fixed a wobbly wheel that had come new on the scooter. A while ago I changed the oil and it was full later that night went to gas station and it was very very low the same day so I topped it off and I think a little bit overfill the max lines just a tad. I still have it sput a bit when I goto start it 50% of the time but it does still start everytime, starter issue maybe?But now the next days riding at about 30km its making a ticking sound somewhere around the back side somewhere thought it was left side but might be back right where that cooling fan is and the ticking sound speeds up as I go faster and faster any idea what it could be? I'll take it back to mechanics tomorrow and edit in if they say anything. Thanks
Hello Fire Gaming if it sput a little when you start could be the sparkplug sometime upgrade to a iridium sparkplug makes a big difference ticking noise at the cooling fan could be the pick up coil touching the flywheel when it turn over sometimes the bolt get lose and the pick up move lower or sometime you need to adjust the valves
@@VirberelloScooterTips found out what it was. While I was checking the pickup coil I looked over and noticed the innertube they installed has a straight tap where you put the air in instead of a 90 degree tap like the original so everytime it goes around it touches part of the metal of the wheel which is grinding off the plastic from the air cap. Guess they didn't check it well enough when they installed it. They also installed the headlight like sideways as well or messed up bulb but the prongs look sideways so I think it's installed sideways because there is a blank spot while driving. Gonna try to make them fix this stuff for free since I already paid them and they messed it up lol. Thanks again man glad I found it. Pickup was still tight BTW and I'll keep the iridium spark plug in mind at next service thanks man!
Thanks for ur information.
My new Honda DIO vs6 makes some gssgssgss soft rubbing noise when particularly I slow down speed .I can't locate the source of this sound. I contact the Honda store they told me it nothing serious. But I am afraid they r not sure about it.
Hello Manoz sometime the front brake rotor makes that noise from age brake or dry out pads or that can be the belt drive rubbing on the lower part of the CVT cover try to travel in a small street or next to a wall with the scooter that will amplify the sound and you can pin point the noise location do not ride to fast when you have a noise remember a noise can become a big problem many times. Thank you for watching my video
My bike fell and I noticed a sound like straining sound. Bike won’t start, I turn throttle to gas and I get no start sounds like air filter . I listened for sound and it’s a straining low sound . What do I do
Hello been watching your videos i wanted to ask you about my noise so i have a gy6 50cc and when it reaches certain speed is like a grinding noise from the back and it does that even when motor off down hill any ideas?
Hello my friend friend sometimes is not easy to understand noices right away but that can be a stretch belt that is grinding on the inside lower part of the cvt cover or a dry bearing at the rear wheel that needs grease . Thank you for watching my video
hey man i love your videos!!!! your awesome, so i have a question(s) for you.... its about a noise, i feel like everything you described as far as what can make a potential noise, may be something my scooter ppotentially may have an issue with... for example the ;location and description of what the weight bearijngs swound like and where the noise is located, as well as gears in the gear box etc. so this is what happened after all my problems started, i was dping 45 and holding it steady, when the belt was just ripped to shreds inside the cvt case... after waiting days for the replacememt belt i put the new one on. and am still counting the issues that followed. but idk where to start or what to fix, i have made small minor adjustments where and when i could see an easy fix. but theres something still really loud going on that i need fixed asap... my take off sucks, sometimes idk if im gona ever get goin, but it does and when it does it sounds like its on it top end and giving everything it has. BUT since all this its now going at least 10mph slower if not more!!!! plese help me!! whats going on w my scooter???
Hello my friend you could have worn out or flat spot on your rollers they are affordable to change 12g or 14g are great for gy6 150cc . Thank you for watching my video
@@VirberelloScooterTips bro thank you so much for taking the time to reply to my post. i had a suspicion that it may be the weight bearing rollers but as confident as u sound about it i will deffinately b taking apart the engine today to inspect them and get new ones. i really appreciate you and your videos!!!!
Thank you for your videos!! I have a 2007 znen 150cc scooter with 800 miles on it. I live in area where there are not a lot of scooters and people who can work on them. I have made a short video of the noise that is coming from the scooter. Can I send the video to you and see if you can help me with the noise? Help please!!
Hello Greg the best way is to join Chinese Project Scooters on Facebook I'm in that group and you can find lots of very good members and you can upload your video there very easily. Thank you for watching my video
Do know where I get starter clutch for sym jets 4 125cc engine will gy6 part work please thanks
Hello my friend I find lots of my parts on amazon or ebay or partsforscooters in florida
Hello, I'm hearing a grind noise coming from the side of my clutch box. I'm only hearing the noise when I accelerate from a stop. I just replaced the clutch but the noise is still there. Any idea of what it could be?
Hello Anthony sometime the belt can grind on the lower part of the cvt cover the best way is to open and look around and inspect for any spot were the belt or a moving part is grinding many company makes the belt little thicker and that stay to much on the top of the clutch. Thank you for watching my video
Hi there, thank you for this video, I was wondering if you can advice me regarding a sound that I just observed today on my scooter, I have a Piaggio fly 125 and today I started hearing like a strong vibration while I was accelerating, was sounding like the engine it has more rotations then usually, after decelerating the vibrations was keep going do you have any idea what can be ? Thank you indeed !!!
Hello my friend sometime when the roller weight start to be little worn will give you vibration
@@VirberelloScooterTips Thank you for your quick response! All the best !
@Hxrvey I ve been having a look today and I found out a cover was detached from the combustion chamber , is the bottom part it looks like is made from plastic it looks like a seal broken and was loosing oil I took a video I can send it to you if you wanna have a look, I don't know much about it. Thanks a lot.
BRAVO Virberello !!! TNX and salut from Slovenia !!)
Hello my friend thank you for watching my video
I change the rollers + clutch central spring and 3 little springs . now first time with new adds i have sound from variator. can be rollers turn over or some other cause the noise ?
Hello supreme93ntm if you change the rollers and place a very light weight 12grams or lower you will feel a vibration and a light grinding but that is normal. Thank you for watching my video
@@VirberelloScooterTips thank you 👍 I install 15x12 rollers. and one roller weight 4,5 grams / previous rollers was 5grams . Im hearing that sound only when i start scooter and idle position
so i got a new one for you.... i replaced the rollers in the variator, the other day my belt got ate up while i was riding, so i replaced it... now i cant get the bike over 30 without some kind of popping sound or maybe the belt slapping the inside of the crank case..?? idk but i DO NOT KNOW what to do or how to fix this!!! i need ur help on this one
Hello my friend that is a little strange your scooter if is a 150cc should go a little faster if you have 150cc scooter you should get a speed of 55 mph or around with 14g weight try to open the cvt cover and run the scooter without the cover but keep your hands away from moving parts and look if the variator open and close or it stay in a fix position and also look the clutch to make sure is moving with a normal spinning force in this situation only your eyes will help you to fix the problem
Hello my friend. I have a ticking sound coming from my scooter. I already did valve clearance. What else could it be. The sound comes when I go on a long ride. Everytime I throttle the sound will be louder.
Hello my friend I have the feeling that the oil pump could be the problem because is not building a lot of flow and is not reaching the valves and they dry clicking one of the way is to open the valves cover and look at the color of the rocket harm if you see they look like chrome that mean they are working at really high temperature also when you ride the scooter you will feel the motor getting really hot really really fast. I hope this can help you
It sounds like My engine blew while I was riding my bike But when I heard it as soon as I heard it I stopped my bike and turned it off and when I turned off the key it was still running until it shut off itself I really would like to figure this out because this is my only transportation
When I try to start my scooter its starts to make a buzzing sound.
Hello Elijah buzzing all the times on gy6 scooter comes from the exhaust or the drive belt grinding some where. Thank you for watching my video
my cygnus have a noise on the back when its stop to start again
I have a rattling noise coming from the exhaust area when I hit about 20mph , any ideas?
Hello Simon that is normal because the quality of the exhaust is not to good but make sure the brackets are not broken and the bolts are nice a tight . Thank you for watching my video
brand new scooter just bought - but when i turn the key and start to accelerate it makes a weird noise sounds like its coming from dashboard only lasts a second and only happens when i start the scooter
Hello Paul little strange sometime the blinker relay makes funny noise when is getting older or has some water infiltration and is under the dash board the best could be to open the front side of the scooter and try to turn on the scooter and look around and listen to the noise. Thank you for watching my video
Please help me out ....
How about a spinning whirring sound when you try to start instead of it trying to turn over ?
Hello my friend that is the starter clutch inside the motor that need to be replaced
I just bought a scooter one week ago & I am noticing that sometimes when I start it, after it turns over & starts running, it makes a single "ting" sound. I had only heard it once or twice, but then today during a cold start, I heard it again. Then it was running fine. I thought I had perhaps accidentally let go of my break before the starter button. I don't recall anyone saying anything about that but I thought it might be that. Then later I started it three times and one of the times it did it again even though I made sure I kept the brake on until after I release the starter button. I'm hoping this is nothing serious, but need to know if I need to take it back in to have it looked at. And did I cause it if I inadvertently let go of the break before the starter.??
Hello Laura if you have a gy6 sometime when the belt is gtting holder slap the top of the kickstarter shaft and makes a ting sound
@@VirberelloScooterTips is this anything to be concerned about? I noticed it only happens when it's cold, so I am hoping it's nothing serious.
Really good..thank you .. i have problem of viberations in front wheel ... an you help me please ....
I'd be happy to help you with the vibration issue on your gas scooter. Vibrations in the front wheel can be caused by a variety of factors, and it's important to identify the root cause in order to address the problem effectively. Here are a few possible causes and troubleshooting steps you can try:
Wheel alignment: Check if the front wheel is properly aligned. If it's misaligned, it can cause vibrations. You can align the wheel by adjusting the alignment bolts or nuts according to your scooter's specifications.
Tire balance: Imbalanced tires can cause vibrations. Ensure that the front tire is properly balanced. You can have a professional mechanic check and balance the tire if needed.
Tire condition: Inspect the front tire for any signs of damage, such as bulges, cuts, or uneven wear. If the tire is damaged or worn unevenly, it may need to be replaced.
Wheel bearings: Worn or damaged wheel bearings can also cause vibrations. Lift the front of the scooter off the ground and check for any excessive play or roughness when rotating the wheel. If the bearings are faulty, they should be replaced.
Suspension components: Check the front suspension components, including the fork and shock absorbers, for any damage or wear. Faulty suspension can contribute to vibrations. If necessary, have a professional inspect and service the suspension system.
Loose or worn-out parts: Ensure that all bolts, nuts, and fasteners in the front wheel assembly are tightened properly. Loose or worn-out parts can lead to vibrations. Check the front axle, brake caliper, and other relevant components for any signs of wear or looseness.
If you're unsure about performing any of these steps yourself, it's advisable to take your gas scooter to a qualified mechanic or a scooter repair shop. They will have the expertise and tools to diagnose and fix the issue accurately. Thank you for watching my video
I think the clutch noise sounds more like tac tac tac. Instead of ker ker ker!! 😂
Hello sometime noise can change but the most important is to pin point where the noise is located . Thank you for watching my video
Yes.. you have great videos!! Very helpful
So I have a ticking sound on the front side of the scooter when I put the key in and put it on the start position but not yet turning on the scooter. It continues when I turn it on. Pls help!
Hello Kevin that could be the blinkers relay going bad ruclips.net/video/cJoOfSHUTiE/видео.html
I have a piaggio fly 125 when I press Start button is doesn’t even make a noise lights comes on tho ????
Hello Lil starter switch could be bad or starter selenoid is not working and need to be replace
Hey I have a question? Why did my scooter slow down to 25mph while driving home. And would not get any faster. Now it won’t turn on after I shut it off. Please help.
Hello I think you need to adjust your valves clearance or you have a broken manifold
My 50cc TaoTao thunder is now making a weird noise after I adjusted the exhaust valve it runs faster but it's making a weird noise like a spitting or I don't know it's hard to describe but I'm trying not to go over 40 but it seems like it wants to go even faster when it only did 35%
Mine does the same thing. You find out what the problem was? Ive read that its the inner valve spring, but I'm not sure. It only has 600 miles and just adjusted the valves, it runs great but a fast tapping noise when I run over 35 mph, gets worse and louder the fast I go over 35
When I have my scooter turned off and I'm sitting on it backing it up before I start it I can hear a clicking sound coming my rear tire and I don't know what it is or if it's even safe to ride that way. Can u help me please
I'd be happy to help you diagnose the issue with your scooter. A clicking sound coming from the rear tire could be caused by a few different factors. While I can't diagnose the problem definitively without physically inspecting the scooter, I can provide you with some potential reasons for the clicking sound:
Wheel Bearings: Worn or damaged wheel bearings can produce clicking sounds when the wheel rotates. Bearings may need lubrication or replacement if they are causing the noise.
Belt: If your scooter has a belt drive, there could be an issue with the belt tension, alignment, or even a damaged that's causing the clicking sound.
Loose Components: Check for any loose parts around the rear wheel area, such as the fender, kickstand, or exhaust mounts. These loose components could be moving slightly when the scooter is manually backed up, causing the clicking sound.
Tire Debris: Sometimes, small debris like stones or pebbles can get lodged between the tire treads and the frame or fender. As the wheel rotates, these objects might cause a clicking noise.
it's important to address this issue to ensure the safety of your scooter. Here's what you can do:
Visual Inspection: Carefully inspect the rear wheel area for any visible issues like loose components, debris, or irregularities.
Tire Check: Check the tire treads, sidewalls, and spokes (if applicable) for any signs of damage.
Wheel Bearings: If you're comfortable with it, you could jack up the scooter to check for any play or roughness in the wheel's rotation, indicating potential bearing issues.
Brakes: Examine the brake caliper, pads, and rotor for proper alignment and tightness.
Belt: Inspect the belt for proper tension and alignment. Look for any damaged teeth.
If you're unsure about any of these steps or if the clicking sound persists after your inspection, it's recommended to have a professional mechanic or technician look at your scooter. They can provide a more accurate diagnosis and perform any necessary repairs to ensure your scooter is safe to ride.
Thank you for the useful video
Thank you for watching my video
Hi friend my 150cc front and rear shocks make a lot of noise. They squeak alot. Any tips what to do?
Hello my friend WD40 Silicone can help a little but is time to change the suspension
@@VirberelloScooterTips I appreciate the advice. Keep up the good work.
When I get to a high speed I start hearing like a winding or almost like the breaks are scraping and or it sounds like engine knock but I doubt it’s that tbh
If you're experiencing unusual noises when riding your gas scooter at high speeds, there are several potential causes that could be contributing to the issue:
Belt or chain issues: Gas scooters often use belts or chains to transfer power from the engine to the wheels. If these components are worn, loose, or misaligned, they can produce a winding or scraping noise at high speeds.
Brake problems: The scraping noise you're hearing might be related to the brake system. It's possible that the brake pads are worn out or there's an issue with the brake calipers or rotors, leading to contact and noise when you apply the brakes.
Engine problems: Engine knock can occur due to various factors, such as poor fuel quality, incorrect fuel-to-air ratio, carbon buildup, or ignition timing issues. While it may not be the first assumption, it's worth getting the engine checked by a professional to rule out any potential problems.
Loose or damaged components: Vibrations at high speeds can cause various parts of the scooter to loosen, leading to rattling or knocking noises. Check for loose bolts, screws, or any visibly damaged components.
Exhaust system: A loose or damaged exhaust system can cause rattling or scraping sounds. Inspect the exhaust system for any signs of damage or loose parts.
Suspension issues: Faulty suspension components can lead to knocking or rattling noises as the scooter encounters bumps or uneven surfaces at high speeds.
Wheel and tire problems: Uneven tire wear, damaged tires, or loose wheels can also produce unusual sounds while riding. THank you for watching my video
my scooter makes a ticking sound if i go over 27 mph i am broke as hell please it wont cost to much to fix it i have a 2008 kimyco 300 cc downtowner i hear thanks to coven 19 it,s hard to get parts any way i need my scooter to get to work what can i do
Hello Gary I' m no to familiar with Kimco 300 but if you have a clicking noise many times comes from the valves and they only need to be adjusted but sometime on gy6 scooter can be a bad oil pump and the valves not having oil pressure they become louder so the best way is to check the valves clearance first and also try to locate and pin point the location of the sound at the motor by placing a large screwdriver handle at your ear and touching the motor with the tip of the screwdriver and that will help you a lot on finding the problem. I hope this can help you also join chinese project scooters on facebook and there you can post a video or a question if someone has a Kimyco 300cc
I am unable to get my scooter to start. I can hear a slight hissing noise or "exhale"-like noise from the engine after I try to kickstart it a few times. I also cannot feel as much air leave the tailpipe as I think I should. Any ideas?
Hello Clark try to check the manifold if you have any leaks or another thing you should check is the valve clearance
If not the above, leaky valve seat(s) most likely. Buy a new cylinder head or to fix it free, disassemble cylinder head and re seat the valve seats.
I have a 2017 taotao and it won’t stop squeaking! And then it gets loud then other days it won’t squeak but mainly it squeaks real bad and I don’t know what to do!
Bad belt, or bad clutch bell
What about a whisteling sound after i get going for a few minutes, and its non stop until i stop
Hello my friend that could be the belt rubbing on the lower cvt cover
I just got a 2022 taotao quantum 150cc scooter, I was riding it home from work and all the sudden it sounded like a motorcycle. What is that and how do I fix it?
Hello my friend I think you lost the exhaust gasket or you lost one of the nuts at the exhaust head just look under the scooter
@@VirberelloScooterTips The exhaust from the engine was totally off lol. Just ordered a new gasket, studs and washers. Also, is there any exhausts you could recommend to make my scooter still sound like a motorcycle? Lol. I kinda like it honestly.
When i push my gy6 forward it makes a squeaking sound by the front wheel but if i reverse nothing please help 🙏southafrica
Hello my friend you need to remove the front tire and grease or change the bearings
I bought a second hand scooter with a 100cc conversion kit but the stock exhaust is still installed. When I rev the motor it makes a little rattle. I'm assuming it's because the exhaust is too narrow. Any ideas?
The rattling sound you hear when revving the motor on your scooter could be caused by a few different factors, including a narrow exhaust, but there might be other possibilities as well. Here are a few potential causes to consider:
Exhaust Restriction: The stock exhaust system may indeed be too narrow for the increased airflow generated by the 100cc conversion kit. This can create back pressure and cause a rattling sound. Consider upgrading to an exhaust system designed to handle the increased volume of exhaust gases.
Loose Components: Check for loose or improperly tightened components within the exhaust system. Vibrations from the engine could cause parts to rattle if they are not securely fastened.
Heat Shield Issues: Inspect the heat shields on the exhaust system. Over time, these shields can become loose or damaged, resulting in rattling sounds. Ensure that they are properly secured and not in contact with any moving parts.
Engine Mounts: The rattling noise could be related to the engine mounts. Over time, these mounts can wear out, leading to increased engine movement and vibrations. If the engine is not properly secured, it can cause rattling sounds. Inspect the mounts and replace them if necessary.
Other Factors: There could be other factors contributing to the rattling sound, such as loose bolts or brackets in other areas of the scooter. It's a good idea to conduct a thorough inspection of the scooter, paying attention to any components that may be loose or showing signs of wear.
If you're unsure about the exact cause of the rattling sound, it's advisable to consult with a mechanic or an experienced scooter technician. They will be able to examine the scooter more closely and provide a more accurate diagnosis based on their expertise. Thank you for watching my video
@@VirberelloScooterTips thank you so much! I'll upgrade the exhaust and take it to a mechanic shop to get checked over. Thanks again
@@VirberelloScooterTips I am taking the scooter to a repair shop tomorrow, but I located where the noise is coming from. It sounds like a loose bolt or nut and it is coming from the transmission. Also, when I use the electric starter, I can hear a metal-on-metal scratching sound from the cvt. Does this sound expensive?
@@veowav A loose bolt or nut in the transmission and a metal-on-metal scratching sound from the CVT could potentially indicate a mechanical issue that needs attention.
The cost of the repair will depend on various factors such as the extent of the damage, the make and model of your scooter, the labor rates of the repair shop, and the availability and cost of replacement parts, if needed.
Sometimes, loose bolts or nuts can be a simple fix that won't cost much. However, if the issue has caused damage to other parts, or if any components need to be replaced, it could be more expensive. CVT issues can also vary in complexity and cost to repair.
If you ear a bolt or nuts sound inside the CVT you could have a broken clutch or broken roller weights for a clutch they will charge you around 200 dollars for a new variator with rollers they will charge you around $140 to replace
I have a ticking noise my clutch starter
I have a ticking noise my clutch started once I hit the gas it stops
Hello Bertito many times the ticking noise comes from the valves and they just need to be adjusted try to pinpoint where the noise is coming from
My scooter recently started rattling only when I’m going slow ? It sounds like it’s coming from the exhaust can you please give me some advice on what’s wrong with it
Hello Harry if you have the original exhaust is normal to ear a rattling sound after a little of times the rivet start to give up the best way to fix the problem is to buy 2 Stainless Steel Duct Clamps 6 inch amzn.to/3f35FA3 and place one at the end and one at beginning of the muffler and that will help the exhaust to last around 10000 miles . Thank you for watching my video and be safe
virberello GY6 Scooter Tips thank you mate. Subscribed 👍🏻
Also is it normal for my back wheel to shake. You dont notice it when your riding but when I had it on The stand today I was revving it and noticed the back wheel shakes
My scooter my some weird sound's around the back part
Like.My scooter gy6 have Big petrol consumption .Whats the problem?
Hello Zdeno Charakter 3 things can came to my mind #1 is worn out piston rings or #2 in line fuel leak somewhere #3 scooter is not burning the fuel at the right time
@@VirberelloScooterTips thanks for tips
Help my gy6 have a whirring noise. When I try to start it. And I just replaced the Bendix with a new one. But still won't start. Just whirring
It seems like you're experiencing an issue with your gy6, and despite replacing the Bendix, you're still encountering a whirring noise without the engine starting. There could be several reasons for this problem:
Starter Motor Issues: The whirring noise may be coming from the starter motor. Check if the starter motor is functioning properly and if there are any loose connections.
Battery Voltage: Ensure that your battery has enough voltage to crank the engine. Low battery voltage can result in a whirring noise without starting.
Starter Clutch: The starter clutch engages the engine when starting. If it's faulty or damaged, it may not be transferring power properly, leading to the whirring noise.
Engine Seizure: Check if your engine is seized. If the engine cannot turn freely, the starter motor will produce a whirring noise without successfully starting the engine.
Ignition System: Problems with the ignition system, such as a faulty spark plug or ignition coil, can prevent the engine from starting.
Fuel Delivery: Ensure that there is proper fuel delivery to the engine. Clogged fuel lines or a malfunctioning fuel pump can lead to starting issues.
It's recommended to systematically check each of these components to identify the root cause of the problem. If you're unsure about any of the checks or if the issue persists, it might be advisable to consult a professional mechanic or seek assistance from a gy6 community for more specific guidance on your scooter model
Thanks virberello, but after I left this statement...I went and checked it out. But it seems like the hole where I insert the Bendix behind the flywheel is worn out/slightly deformed. I placed the Bendix in but it wouldn't stay still. any help would be appreciated.
Hey how are you? Everytime I try to start my scooter it does this knock sound, and it doesn't turn over
Hello my friend that sound is no good could be the crankshaft or the Primary Starter Drive the only way is to inspect the inside of the engine.
Thank you for watching my video
@@VirberelloScooterTips could I facetime you some how? I want to you to see exactly what's going on
My scooter is a little old it look something like this www.google.com/shopping/product/12033480275939562793?q=ttyg5+chinese+scooter&start=120&bih=652&biw=412&hl=en&tbs=vw:l,ss:44&prmd=sivn&sxsrf=ALeKk006udXtJeErkArr8vhnadmFeKadIA:1589121566654&prds=num:1,of:1,epd:874328406843650706,prmr:1,cs:1
I have a little bit of ticking sound and the Mechanical who replaced the belt for me said .. Your bike sounds good nothing wrong with it.. But i dont know what to do.. i know my bike wasn't like that before it's little bit faster now but that tic tick tick sound is killing me 😔please help 😵😵
Hello Karime ticking noise can be from the valves harms after lots of miles the oil pump due to wearing start to lose the power of keeping the oil flowing with pressure and can not send the oil to the top of the motor so the top end will be a little dryer and hotter in temperature and will make noise before something is going to break but sometime the noise can come from the crankshaft bearing and that is totally another problem
@@VirberelloScooterTips thanks a lot god bless you 🙏❤️
I changed the muffler ,, still getting loud noise from muffler side. when I give it gas.
Hello my friend you need a new gasket at the muffler or you can try with high temperature gasket maker . Thank you for watching my video
My moped is Making a rattling sound that sounds like a lawn mower and I don't know where it's coming from
Hello my friend I believe is the front header exhaust pipe there is a little mesh that get lose sometime amzn.to/3Fz56Od
OMFG!!!!!!!!!!!!! REALLY!!!!!!!!!
I have had this squeaking noise driving me absolutely crazy.....
I been having problems with exhaust because when I first got new scooter, muffler didn't come with the brackets to secure it and I didn't have a clue so... first problem I had was manifold bolts broke off inside the motor... got one out but other one... well... let's just say I drilled it out but it too big for the bolt so Its attached with 1 good bolt, a shady one and got some JB Weld Xtreme Heat and layered it on like mortar between gasket and manifold lol....
The new brackets I put on muffler popped off taking the manifold bolts with it again so I redid my "ducktape fix" and then the SQUEAK that would only SQUEAK when I was riding it.... and I thought it was the muffler bracket bolt squeaking or muffler rubbing the post......
NOPE!!!!!! It was the SAME squeak that drove YOU crazy. The kick start rubbing the center stand...... I even took EVERYTHING out of my seat storage box trying to find it.... lol
Personally I would have started the video with this "noise" because it's the only sound/noise that sounds "important" but nothing to do with the mechanical workings of anything. The rest were all noises that happen when "bad" things happen lol.
I bet I could watch 100 "other" videos of people explaining "wierd noises" and not see anyone point out this squeak that will drive you BONKERS!!! lol
Thank you for watching my video
hi what most i do if my rockers make noise on my scooter
Hello if the rockers are the weight rollers you just need to replace them
how please mak n vidioe
Sir my scooter give sm kind pat (idk how to explain)sound while releasing accelerator, while driving.
(N sorry fr my English)
Hello my friend many time when you release the acceleration you can have a pop from the motor that say your motor is running to lean . Thank you for watching my video
Lol dressed to impress
mine is making a whistling noise from the CVT area
Hello is better to remove the cvt cover and see before something will break down
@@VirberelloScooterTips I already have. I replaced the belt and oil.
@@aa-py6rl that could be a bearing somewhere that make that noise
If you hear what sounds like a helicopter propeller coming from the front wheel its a good chance your wheel bearings are going.
Hello John yes that could be the bearing or the brake pads thank you for watching my video
i had this funny thought that this guy was a valet driver and one day he had to park someones scooter, he liked it so much now he does this.
Ha Ha Ha you very funny I work in the restaurant business and every day I go work with my scooter . Thank you for watching my video
@@VirberelloScooterTips heck yea man very informational keep em coming!
My crankshaft is making noise every time I start my 150cc
Hello my friend when the crankshaft make noise is a big problem because to change that part you will have to open the all motor I had that problem before but I didn't have lots of time on my hand so I decide to get a new motor and that was a faster fix but a little more expensive
@@VirberelloScooterTips what's motor look like ? Should I order from Amazon
@@VirberelloScooterTips are you talking about a tc motor ??
@@merjimjimenez1361 I order this gy6 long case 150cc amzn.to/3ph5FCy one time but for next time I will buy a gy6 150cc B motor that are better quality like a taida made in Taiwan
@@VirberelloScooterTips your right that is expensive. I think I'm just gonna buy some parts for my crankshaft and new starter clutch
Okay?
Okay ? Thank you for watching my video
Awesome video! What do you think of this noise? I can't figure it out. It only starts to happen around 10 mph and get's more high-pitched the faster you go. ruclips.net/user/shortsDFArMHwxlOI
Hello my friend I try to click on the video but I can not see anyway
The noise you're describing on your gas scooter could be caused by a few different issues. Some common causes of a high-pitched noise that increases with speed include:
Loose or worn drive belt: The drive belt connects the engine to the transmission and if it's loose or worn, it can create a high-pitched noise when the scooter is in motion.
Worn or damaged bearings: If the bearings in the wheel hubs or transmission are worn or damaged, they can create a high-pitched noise when the scooter is in motion.
Worn or damaged gears: If the gears in the transmission are worn or damaged, they can create a high-pitched noise when the scooter is in motion.
Worn or damaged chain: If the chain is stretched or damaged, it can create a high-pitched noise when the scooter is in motion.
Worn or damaged variator rollers or sliders: The variator is responsible for adjusting the transmission ratio and if the rollers or sliders are worn or damaged, they can create a high-pitched noise when the scooter is in motion.
Thank you for watching my video
Same problem on my gilera runner 50, high pitch sound and still dont know what it is…maybe bearings on crankshaft? Did you solve problem?
I have noise coming from where the stator side it sounds loud. What could it be? Also looks like I'm leaking gas from the cvt side.
Based on your description, it's possible that the noise you're hearing is coming from the motor or the bearings on the stator side. Some possible causes of this noise could include:
Worn bearings: Over time, the bearings in a motor can wear out and cause a grinding or rattling noise. This can be caused by a lack of lubrication, exposure to contaminants, or general wear and tear.
Loose or damaged parts: If there are loose or damaged parts in the motor, they can cause vibrations and noise. This could include anything from loose screws or bolts to damaged fan blades or rotors.
Electrical issues: Problems with the electrical components of the motor, such as a loose or damaged wire, can also cause noise. This could be a buzzing or humming sound, or a popping or cracking noise.
Stator core issues: A damaged stator core could also be the source of the noise. This could be caused by a variety of issues, including overheating, moisture damage, or physical damage to the core.
or you could have a damaged starter clutch and for the gas leak at cvt you need to remove the cover and see and that can leak from the lower part of the carb area . Thank you for watching my video