How To Fix Car AC That Blows Hot Air
HTML-код
- Опубликовано: 7 сен 2024
- I fix the AC in this 2010 Ford Fusion. It would stay cold for a few seconds then blow hot air. I show you how to determine if its the actuator.
PLEASE CHECK OUT THIS GREAT ONLINE BOUTIQUE!:
nourishbyallie...
Instagram: / nourishbyallie
Facebook: / nourishbyallie
Pinterest: / nourishbyallie
Thank you Soundcloud Artist:
Music Credit: OurMusicBox (Jay Man)
Track Name: "Raw Rivalry"
Music By: Jay Man @
Disclaimer: Due to factors beyond the control of SteadFast 2277, I cannot guarantee against improper use or unauthorized modifications of this information. SteadFast 2277 assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. SteadFast 2277 recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of SteadFast 2277, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not SteadFast 2277.
So, here we are, 4 years later, and this video is still helping people. Thanks for that! My AC started intermittently not working, but then stopped completely By following your instructions, it does look like the actuator (and, hopefully not the HVAC control), so I've ordered one from Amazon which will be here in a couple of days. In the meantime, it's still too hot to do without AC, and I noticed that, when I first turned the car on, with the AC set to full, it would start blowing cold, but then fail over to hot. So, I climbed under the steering wheel, cranked up and car, and then disconnected the actuator before it could go hot. VOILA! Took it for a drive and it stayed cold the whole time. Hopefully that will do the trick until the part arrives and I can put it in. Also hope this helps someone else in a similar situation. Thanks again!!
Thanks so much for posting this video! I also have a 2010 Fusion with the exact same problem. It started acting up last summer, but only when it was extremely hot outside. Now, this summer it started doing the same thing until it was doing everytime I use the car... going to blowing hot after a minute of cold air. Don't know about the info/reset thing mentioned below, will have to check into that. What I did do for a temporary fix until I could get a replacement part is this: With A/C on, fan on, and temp adjust set to hot all the way, turn car off for about 10 secs, then start it back up. Like in the video, gradually turn temp adjust all the way cold, and make sure it's blowing good and cold. Then unplug the actuator and it will stay set in the cold position. Ahhhhhh!!!! Nice cold air until you can get around to replacing the actuator.
Great video! Thx ☺️
Did replacing the door thing fix the problem?
Thank you! Your video was extremely helpful. I was having the same problem with my car. I was trying to locate the actuator and couldn’t find it. Thanks again 👍🏻
Before you do anything or buy any parts to resolve a/c drifting from cold to hot .
Check Your Car battery. The car will start up just fine but will not have enough power to run all the electronics properly.
I have a 2010 ford Fusion. My clutch will not kick in on the compressor. Does the air door actuator play apart to keep the clutch form working? Hope you reply, Thanks,
I watched this video & turned my nob slow from hot to cold like he did & it started working, I been a week with no ac but hey it’s working now which is so weird
I just turned my temperature settings slow like said I heard it opened up and l left it on that setting and now my ac is working
Hey buddy really appreciate your video. , i have a 2012 ford fusion and mine blows cold for few seconds and then it is like the vent adjust then blows hot. Do you hear the vent or air adjust when it goes from cold to hot?
Thank you so much. I'm having the same problem.
I have a 2015 ford escape when I start to vehicle all modes works properly when I turn off the vehicle when the vehicle reaches normal temperature the a/c mode only works on defrost and floor mode I did change the blend door actuator Humm. I'm stuck HELP PLZ
can you do a video on how to take those connectors loose once it took me 2 hrs trying not to break one lol
I tried all suggestions and nothing worked. So out of desperation l hit the reset info on the steering wheel and it worked.
Wtf. I just did this and it worked for me too. This has to be a system issue.
Jerome Goodman Where is the reset info button?
A Colleen Bauer Nigro it’s in the steering wheel buttons. I’d google it for further clarification
My ac used to blow but then stopped.... the panels are clean the fans work but the line just froze up :/ idk what happened
Was the ac clutch engaging/ engaged when you checked it while it was only blowing out hot air? Or was it disengaged?
Is actuator under dashboard on 2010 ford focus se?
So mine didn’t blow cold for a second it just doesn’t get cold. I used stop leak, no visible leaks. Used AC Pro to recharge, it held pressure, didn’t get cold. Is it the compressor?
It will get hot at the heat setting. But when I get to cold notch by notch it gets cooler but not as cool as it should. It’s a 2010 Ford Focus DE
Thank you! Same car same symptom and the dealer charged me 1500 to not fix it.
Turn the lights on and the AC will work again. No joke
Mine does that BUT it won't stay cool while idle. Any fix for that?
Ok
This is most likely an easier more likely to work fix.
ruclips.net/video/kq9InunWkPw/видео.html
I watched it ,i will go to try it,if it works,realize u a good guy lol
*WARNING: watch this user’s follow up video*
It is hugely irresponsible for you to keep this content public after the “fix” which you demonstrate here proved wrong after a day. I just wasted about an hour of time and about $50 on the part (blend door actuator for air temperature blending), only just like you to find that the real problem lies in the control module.
It is plain sad that you would not even take the time and care to take this video down or at least include the updated information in the video’s description. What you learned a day later, when the AC failed again, rendered this video at best useless.