So i just want to say that over the last couple years ive replaced the throttle body 6x and each time the truck works perfect for about 6 months. This time it didnt. Id replaced multiple sensors about 2 years ago. I had 5 volts to each with key on and 0 volts with key off. Had etc lightning bolt symbol and in limp mode for 2 months. Multiple shops thought it was pcm or ground wires. Replaced the crank sensor and it runs amazning!! I had a map sensor code on and pending cyl 8 misifire. All gone and runs amazing.
Thanks so much for the logical video of how you figured this out. I'm guessing I have the same problem but now I know how to verify rather than just replacing parts.
I really wish I would've found your video earlier... My 2017 ram won't turn over and it has a shit ton of lights on. Tries resetting. Bought new battery, new throttle body, changed spark plugs. And still won't start. I was just saying to my buddy I think it's 1 thing that's messed up causing other codes to falsely read errors.. I'm gunna try this after work today. Thanks man!
Im really hoping this might be my problem. Im getting low bar pressure code. Etc red lightning bolt on. Replaced the throttle body and all pulgs and wires over last couple years. Cam and crank sensor couple years old as well as iat and map sensors. Put new main ground wires on.
I heard a rattle on 2004 Durango 5.7 L Hemi after removing crank position sensor and putting back in. I was unable to get an ohm reading on the sensor. Do you think the rattle is from how starter aligns back in or that rod broke? I had heard a rattle on previous starts but it would go away after start.
I wouldn't think that rattle would be the starter. Could have a cracked flex plate or even a loose one. Had that on a customer's Dodge Ram. Had a little bit of a rattle and some other shop said he needed a new trans. After I looked at it I seen the flex plate moving back and forth.
You can check volts on back side of plug also mine turned out to be oil sending unit or pressure unit but they say us ram guys should carry crank sensor with us
Thanks for taking the time with this video! We've got a 2005 Durango with the 5.7 HEMI that keeps dying when we drive over a bump. It cranks right up every time. In fact we've gotten so good at it, that we can pop it into neutral and turn the key to start it up while rolling. Would this be related here?
I have a 07 that just randomly dies as well with the 5.7 , these things are a electrical nightmare, I replace cam and crank sensors every year because they fail, but now its gradually progressed into more, where there is electrical faults randomly through out the engine bay, misfire on 4 or 1 day it will be misfire on 7, one day it can be cam shaft intermittent, its the process of just going through everything and checking , Hell even low oil/wrong oil will cause these faults as well, the codes are so generic and undefined .....
My 08 charger has the p0340 code and after this I bet it’s the crank sensor , it’s a Autozone aftermarket brand so I bet it short out quick , I also replaced 1 coil pack brand new from auto zone and it already has went out problem fixed now but only code p0340 is my prob
I'm not a fan of always going to the dealer for parts. I will say Mopar is a little on the unique side where it's best to use factory parts if you can.
Thanks for the video. I have not tried it but I will and get back to you for everyone else having the same problem.
Thanks for info you had same basic symptoms but my problem was it keeped throwing cam code you info lead me right direction thank you good video
Glad it could help you. Did you get it fixed?
Very good video. No BS. I have a 5,7 Ram. installed new engine this weekend. Crank nostart. I will test this. Thanks :)
So i just want to say that over the last couple years ive replaced the throttle body 6x and each time the truck works perfect for about 6 months. This time it didnt. Id replaced multiple sensors about 2 years ago. I had 5 volts to each with key on and 0 volts with key off. Had etc lightning bolt symbol and in limp mode for 2 months. Multiple shops thought it was pcm or ground wires. Replaced the crank sensor and it runs amazning!! I had a map sensor code on and pending cyl 8 misifire. All gone and runs amazing.
Thanks so much for the logical video of how you figured this out. I'm guessing I have the same problem but now I know how to verify rather than just replacing parts.
Good video thank you. You do a great job. this is the first video I’ve seen that isn’t crap. Great job. It didn’t fix my truck but it did help.
Thanks I'm in the middle of this exact issue THANKS !
I really wish I would've found your video earlier... My 2017 ram won't turn over and it has a shit ton of lights on. Tries resetting. Bought new battery, new throttle body, changed spark plugs. And still won't start. I was just saying to my buddy I think it's 1 thing that's messed up causing other codes to falsely read errors.. I'm gunna try this after work today. Thanks man!
Did it work?
I have an ‘11 that does this in the cold weather. Warm weather it starts fine.
Right on, my 12 is a no start...good vid, will be doing some checking if ever it stops raining
PCM FUSE PULL RESET QFTER REPLACING PARTS
Thanks for your video very clear and very enhancing, thanks a lot!
Thank you!
Im really hoping this might be my problem. Im getting low bar pressure code. Etc red lightning bolt on. Replaced the throttle body and all pulgs and wires over last couple years. Cam and crank sensor couple years old as well as iat and map sensors. Put new main ground wires on.
I heard a rattle on 2004 Durango 5.7 L Hemi after removing crank position sensor and putting back in.
I was unable to get an ohm reading on the sensor.
Do you think the rattle is from how starter aligns back in or that rod broke?
I had heard a rattle on previous starts but it would go away after start.
I wouldn't think that rattle would be the starter. Could have a cracked flex plate or even a loose one. Had that on a customer's Dodge Ram. Had a little bit of a rattle and some other shop said he needed a new trans. After I looked at it I seen the flex plate moving back and forth.
You can check volts on back side of plug also mine turned out to be oil sending unit or pressure unit but they say us ram guys should carry crank sensor with us
Just like the jeep XJ and TJ guys. Very common. I carry an extra crank sensor in the XJ.
Thanks for taking the time with this video! We've got a 2005 Durango with the 5.7 HEMI that keeps dying when we drive over a bump. It cranks right up every time. In fact we've gotten so good at it, that we can pop it into neutral and turn the key to start it up while rolling. Would this be related here?
Its definitely possible.
I have a 07 that just randomly dies as well with the 5.7 , these things are a electrical nightmare, I replace cam and crank sensors every year because they fail, but now its gradually progressed into more, where there is electrical faults randomly through out the engine bay, misfire on 4 or 1 day it will be misfire on 7, one day it can be cam shaft intermittent, its the process of just going through everything and checking , Hell even low oil/wrong oil will cause these faults as well, the codes are so generic and undefined .....
Where do you get the wiring diagram from?
What's the voltage to that crank plug supposed to be
New follower
My 08 charger has the p0340 code and after this I bet it’s the crank sensor , it’s a Autozone aftermarket brand so I bet it short out quick , I also replaced 1 coil pack brand new from auto zone and it already has went out problem fixed now but only code p0340 is my prob
I'm not a fan of always going to the dealer for parts. I will say Mopar is a little on the unique side where it's best to use factory parts if you can.
Rock Auto is a godsend when it comes to Daimler/Chrysler sensors. The oe NGT sensors are cheaper there than the aftermarket replacements.
Ok how bout start in limp mode… every sensor had 5 volts with key OUT except the crank sensor. It’s the only one that have zero volts with key off
Replace sensors then do a PCM FUSE PULL RESET!
How do you do this?
I dont have any volts in the Cam sensor or the map bout to check crank sensor
Ive replaced the trottle body,crank sensor, cam sensor, AIT sensor nd map sensor i know theres no spark nd no voltage going to any of these sensors
All ignition coils, spark plugs nd wires were just replaced 4 days ago
I even disconnected the alarm but that didn't get it to work does anyone have any other ideas 💡
@joseRodriguez-hc7uv you may want to look at the ECU. Or you have a connection problem somewhere.
Did you figure anything out? That's a lot of parts replaced. Was it running fine then quit? Did you check your main grounds?
my TPS voltage is way lower then 5-3 volt range
20 min for 2 min worth of content
welcome to youtbue
I couldn't disagree more. He walked through a logical way of finding the problem. This was very informative to me.