Compliments for the nice ideas! Usually I watch these hack videos only to laugh or to be astonished by their lack of safety, but this is truly worthy! Loved the round “washer” chuck jaw spacers, will build it for me!
I've used rings for setting a part outwards in the 4 jaw so that I could indicate it on it's sides. I wish I could chuck stuff into a 3 jaw rather than a 4 jaw, but that's what I have to do
Ahora mismo voy por un torno para aplicar estos trucos de vid utiles. No se como no se me ocurrieron antes. Debe haber sido porque no tengo el torno. Que bestia!!!😂😂😂😅😅😅
I might always and make a comment. On your interested projects. I like both. 1/ Your videos are good. 2/ I have also, the projects are pretty interesting.
Wenn man den Unterschied zwischen einer Drehbank (Metall...) und einer Drechselbank (Holz...) nicht kennt, sollte man auch keine ach so tollen Tipps geben. Aber Hauptsache was gepostet !!! Resultat: Banned
1. It's a shame about the electrode, a piece of stronger wire will do the job. Otherwise everything is great.
Welcome!
Good work my bro👍👍👍
Thanks bro😉
Place is cleaner than my kitchen. Nice ideas. Thanks
Thank you so much and welcome!
Muito obrigado !
Welcome my friend!
Great idea for lathe machines
Thank you😉
always great ideas. Thank you
Thank you😉
Fantastic!
Welcome my friend!
You best master❤❤❤
Thank you so much🙂
Nice, very useful hacks ! Thx bro 😊
Thank you, bro!
Excellent video. You always come up with simple solutions to unknown problems.
Keep it up.
Thank you my friend and welcome🙏
The rings as spacers is a good idea, the other stuff is pretty much old hat. 👍👍👍
Thank you so much and welcome!
MASHA.ALLAH.GOOD.WORK
Welcome my friend🤝
Excelent video. Simple and practical ideas
Thank you so much and welcome!
Bravo Türkiye den selamlar 🎉
Thank you so much and welcome!
Parabéns mais uma vez ao mestre da competência e da simpatia!eu só não sei de qual país vc é !
Thank you my friend and welcome😉
Très bonne idée very cool
Welcome my friend!
Compliments for the nice ideas! Usually I watch these hack videos only to laugh or to be astonished by their lack of safety, but this is truly worthy!
Loved the round “washer” chuck jaw spacers, will build it for me!
Thank you so much and welcome!
Nice machine and area.
Thank you , man of many nifty tricks and tips 👍👍
Nice , thanks for showing your work
Thanks bro😉
Ottimo lavoro 👍 così non rovina il pezzo da stringere coi morsetti
Thank you😉
Good idea. I've used shims in the past for machining offsets on an existing diameter pilot hole.
Thank you and welcome👍
Very nice ideas sir. Great work. It looks great.
Good tools❤
Thank you very much for watching and welcome my friend!
Good!!!
Thank you so much and welcome!
I've used rings for setting a part outwards in the 4 jaw so that I could indicate it on it's sides. I wish I could chuck stuff into a 3 jaw rather than a 4 jaw, but that's what I have to do
Welcome🙂
Muito bom! E sem um piu 😂
Thank you very much🙂
👍👍👍
Thanks😉
very nice
Thank you very much and welcome👍
I like the ring stop trick
Nice video for a home machinist. People that machine for a living will know this stuff.
supper
Thank you🙂
I wouldn't quit my day job if I were you.
Thank you🙂
Instead of rechucking after every part-off, part-off 3 or 4 or 5 in a row, then rechuck. Time is money.
Time Is life...
2 good ideas nothing happened in number 2 .. why did you knock the flux off the welding rod ?
If the flux crumbles on the machine bed, it is undesirable for the lathe! Welcome😉
These are ok I guess, but I’m sure someone out there didn’t know some of these and learned something new and that makes it all worth it…
how do you keep your lathe so damn clean????
I wipe down and clean up debris immediately after every job and in the process! Welcome!
Ahora mismo voy por un torno para aplicar estos trucos de vid utiles. No se como no se me ocurrieron antes.
Debe haber sido porque no tengo el torno.
Que bestia!!!😂😂😂😅😅😅
Anda mengerjakannya dengan baik❤
Thank you😉
I might always and make a comment. On your interested projects. I like both. 1/ Your videos are good. 2/ I have also, the projects are pretty interesting.
Thank you, my friend🙂
#1 Now remind me why you wasted a good welding electrode..?
You could buy soft jaws 😀⚙️🤙
Thank you, bro!
il trucco degli anelli sulle griffe non ne ho capito l'utilità
These rings serve as a stop for a specific workpiece size and replace the notch in the reverse cams of the lathe chuck! Welcome my friend😉
E io sono stato a guardare queste cose, tempo perso anzi buttato !
Wenn man den Unterschied zwischen einer Drehbank (Metall...) und einer Drechselbank (Holz...) nicht kennt, sollte man auch keine ach so tollen Tipps geben. Aber Hauptsache was gepostet !!!
Resultat: Banned
seh ich auch so.
Dlaczego nic nie mówisz w swoich filmach?
My videos are asmr! Only sounds of tools and machines!
A new machine with a dro ,no power feed
This machine how much
13.000$ Lathe China!
Y después de 25 años como tornero... Ahí se fueron 5 minutos de mi vida desperdiciados... No ví los súper trucos de la vida...
¡Vive y aprende! ¡Verás mucho más amigo mío! Bienvenido.
What do you want? A medal ??😅😅
معنی نداشت.
Maistre imi pare nespus de rău strungu tău nu are gradație pa
😂😂😂😂😂😂😂😂😂😂
Everyone already knows this stuff.
STUPEFACENTE!
What a spectacular waste of time lmaolmao
These are simple and useful turning tricks! Welcome!
🤩🤩🥰👍👍👋👋