How to Replace Hydraulic Engine Mount 2006-2011 Cadillac DTS

Buy Now!
New Hydraulic Engine Mount from 1AAuto.com 1aau.to/ib/1AEM...
Like many other load bearing parts on your vehicle, the engine mount contains rubber bushings for smooth, comfortable driving. And like other parts, the rubber bushings can wear and rot over time. It’s a good idea to replace them when that happens. This video shows you how to install a new made to fit TRQ engine mount on your 2006-2011 Cadillac DTS.
This process should be similar on the following vehicles:
2006 Cadillac DTS
2007 Cadillac DTS
2008 Cadillac DTS
2009 Cadillac DTS
2010 Cadillac DTS
2011 Cadillac DTS
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXA...
• Pry Bar 1aau.to/oa/1AXA...
• 13mm Wrench 1aau.to/oa/1AXA...
• 10mm Socket 1aau.to/oa/1AXA...
• 13mm Socket 1aau.to/oa/1AXA...
• 15mm Socket 1aau.to/oa/1AXA...
• 18mm Socket 1aau.to/oa/1AXA...
• 21mm Socket 1aau.to/oa/1AXA...
• Trim Tool Set 1aau.to/oa/1AXX...
• Hose Clamp Pliers 1aau.to/oa/1AXA...
• 3/8 Inch Air Impact Gun
• T25 Socket 1aau.to/oa/1AXA...
• Socket Extensions 1aau.to/oa/1AXA...
• Swivel
• Drill
• Block of Wood
• Drain Pan 1aau.to/oa/1AXA...
• Floor Jack 1aau.to/oa/1AXA...
• Pick 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Cadillac DTS 2006-2011 1st Generation: • Cadillac DTS 2006-2011...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money

[@commanderog1879]

And what about the other motor mount

[@mikechrist07]

This is a horrible design but it's gotta be done 😢

[@commanderog1879]

What happens if i allow that r-134 to escape

[@jonathancastillo3004]

Ain't no way u had to do all that 😂😂

[@weswalters5607]

There was no need to take the bracket off… way too much stuff was taken apart for no reason… couldve been done by just removing the top bolt with a wrench from underneath and the 2 bottom bolts

[@adama4834]

Thank you for saying that cuz I thought the same thing and had the thought this guy was crazy.... But thought I might have been and I almost went went through the process. Glad you made the response

[@hamdanae]

T about the upper mount, the bushing rubber was cracked

[@rebeccaprice2457]

Could you please show us the broken motor mount so I can see how it breaks? Where is your repair shop? I need a repair.

[@rebeccaprice2457]

Also, how many motor mounts are there and which ones break most often.

[@tankdawg32]

@@rebeccaprice2457 I believe there are four mounts total. Front, rear, and both sides.

[@UrbanSniperWTF69]

Thanks for the vid 🙏🏽

[@kingdubbs8284]

Hello I am having a hard time find the neutral safety switch in 07 dts. Do you have a clue where it would be

[@knowledgeispower4235]

Did u really have to remove all of that just to change the motor mount?

[@hittz8331]

No....LOL

[@tomgentry6409]

This has to be done to my Cadillac my front motor mount is broken

[@Dolf_713]

Do y’all have a video for a deville 00-05?

[@hittz8331]

ruclips.net/video/ZO1EUZ5WWVc/видео.html