ruclips.net/video/bui43JItzJQ/видео.html video on how to install the flywheel this is the updated version thanks for watching and please subscibe and share
I live in LA and drive to Metric Autosport in Huntington Beach to get my 2014 VW GLI fixed. Local mechanics near LA and the stealership tend to charge 30-40% more. I was told they charge $550 to drop the DSG. My car has 200K, luckily many highway miles, but I am beginning to hear the chatter while creeping forward in traffic.
For future reference my 2.0 TDI DSG was making no rattle noise at all, then I drove through flood water and put the bell housing part under water, and a heap of what looked like gravy drained back out. This was obviously all the worn flywheel material, and it started rattling like mad a few hours later as it dried back out. My car was at 260,000kms. Seems the crap in there can keep it quiet yet it's still on the way out, , so something to watch beyond 200kms / 150 miles or so!
I have been experiencing a problem with the DQ250 gearbox for the last 10,000 km and it sounds like this: When the clutch engages there is a clunk, the gear shifts are very linear and nothing is felt, except a clunk and a little jerk. I have noticed this phenomenon also when I go, in any gear, take my foot off the accelerator and put it back on, a clank is heard. I'll leave some videos below with what I'm trying to explain. I'm guessing it would be the dual mass flywheel, the car having 210k km. The dog bone and mounts are ok. Replaced the CV Joints but nothing changed. The sounds appears when you try to reproduce the noise which gets louder and louder the more you try to reproduce it Also when i'm in idle i feel sometimes some vibratians and when i put it in D, the vibration dissaperes. On VCDS there's no errors from mechatronic unit. What do you guys think? Video on my profile.
Hey what size are the 6 screws that hold it on??... My new DMF did NOT come w/ the 6 screws. I've mostly found torque to yield specs, but some guys on a tdi forum are saying they're NOT torque to yield, so the truth is a bit of a moving target right now. Torque to yield is still new to me, seen any good explanations?? - thanks
@@ben_gurin yes, I went with the Luk brand. Car drives like new again! Apparently they made it better updated version then the OEM one. And cheaper to.
thanks! i just ordered a luk dmf! my tdi is at 109k , should i replace the clutch pack? and if so what should i do, im seeing chinese clutch disk packs for like under 200$? everything else is just so expensive
it usually gets pretty loud before it totally breaks. eventually it will fall apart and damage the trans housing. I usually drive it for a week or 2 before I get to it. .
ruclips.net/video/bui43JItzJQ/видео.html
video on how to install the flywheel this is the updated version thanks for watching and please subscibe and share
Daul mass flywheel maybe for torque shock but it is also a vibration damper on the TDI diesel engine
I live in LA and drive to Metric Autosport in Huntington Beach to get my 2014 VW GLI fixed. Local mechanics near LA and the stealership tend to charge 30-40% more. I was told they charge $550 to drop the DSG. My car has 200K, luckily many highway miles, but I am beginning to hear the chatter while creeping forward in traffic.
For future reference my 2.0 TDI DSG was making no rattle noise at all, then I drove through flood water and put the bell housing part under water, and a heap of what looked like gravy drained back out. This was obviously all the worn flywheel material, and it started rattling like mad a few hours later as it dried back out. My car was at 260,000kms. Seems the crap in there can keep it quiet yet it's still on the way out, , so something to watch beyond 200kms / 150 miles or so!
Did u swap out the pilot bearing when you changed this? Looking forward to doing this in my mk5 r32
Would of loved to see the transmissions install. Lots of videos on flywheel but not on transmissions install.
Thats great. I knew my dmf was going through accelerating and braking. I thought that shutter and hard idle on cold starts was something else
So what was the total $$ w/ shippping & all ??
I have been experiencing a problem with the DQ250 gearbox for the last 10,000 km and it sounds like this:
When the clutch engages there is a clunk, the gear shifts are very linear and nothing is felt, except a clunk and a little jerk.
I have noticed this phenomenon also when I go, in any gear, take my foot off the accelerator and put it back on, a clank is heard.
I'll leave some videos below with what I'm trying to explain.
I'm guessing it would be the dual mass flywheel, the car having 210k km.
The dog bone and mounts are ok.
Replaced the CV Joints but nothing changed.
The sounds appears when you try to reproduce the noise which gets louder and louder the more you try to reproduce it
Also when i'm in idle i feel sometimes some vibratians and when i put it in D, the vibration dissaperes.
On VCDS there's no errors from mechatronic unit.
What do you guys think?
Video on my profile.
Hey what size are the 6 screws that hold it on??... My new DMF did NOT come w/ the 6 screws. I've mostly found torque to yield specs, but some guys on a tdi forum are saying they're NOT torque to yield, so the truth is a bit of a moving target right now. Torque to yield is still new to me, seen any good explanations?? - thanks
Thanks for the info from the UK England :-)
very good one more registered and will like
What was the part number for the flywheel?
Thank you for this video after this video i am sure the my DMF is ok and i not need to change
Is it possible to use a conversion flywheel kit to mono-masse ? because they are more reliable.
Your comfort might degrade, but yeah, it's doable.
When buying a new DMF is Luk the only one that’s updated, and what would I need to look for as far as the upgraded one?
any luck with finding an upgrade or somthing good? im on the look out and dont know what to get
@@ben_gurin yes, I went with the Luk brand. Car drives like new again! Apparently they made it better updated version then the OEM one. And cheaper to.
thanks! i just ordered a luk dmf! my tdi is at 109k , should i replace the clutch pack? and if so what should i do, im seeing chinese clutch disk packs for like under 200$? everything else is just so expensive
How you remove the flywheel
I'm getting a terrifying grinding noise at low speeds that go away the faster I go. Could this also be problem?
not sure about that.
I had the same. Garage fixed it, seemed to be some wrongly mounted service part(diff)?
@@oscardominguez1680 mine turned out to be the flywheel. Replaced and all is good
@@tyjohnson7428 was it expensive?
@@oscardominguez1680 about $900 USD all In for parts and labor. Wasn't great but I wasn't ready to junk the car
is it ok to drive with a failed DMF ?
it usually gets pretty loud before it totally breaks. eventually it will fall apart and damage the trans housing. I usually drive it for a week or 2 before I get to it. .
@@Mikefngarage Thank you for your reply. I’m getting loud and continuous sound in Neutral. Should I change only DMF or clutch too?
@@tilkymacky above 200k miles I would change the clutches below just the flywheel
Drove mine for over a year and I'm just getting it done now
I just changed the flywheel as I started trying starting trouble.
Bs I accidentally ordered the 8 bolt dsg dmf instead of 6 we’re can I find it
Best place is www.cascadegerman.com
I hope i can do this job correctly 😅