pezo 307sw 1.6hdi.All the best I am from Serbia and the master would charge about 50euros for hand without parts.Thanks to you,I did everything myself and took my wife and children to meal and movie.
Big thanks for these tutorials, i also watched the trans oil change in addition to this. Just as a note, the 307 that i was working on had somewhat of a "weird" transmission casing. The drain plug was on the side of the casing like it is on some other 307s i've seen rather than in the front side like in this video. But the fill plug was about where it is on your car and the venting hole had just a plastic cap that pulled off instead of threaded plug. Got the job done though, was a bit easier than i first thought.
Can this cause abs failure? As my abs lights turns on above 45 50mph,.and works normally if i switch car off and on again and its making a clunk noise from that side Clunk clunk sound while breaking with abs on, and no clunking when abs deactivates and warning light on in dash.
Nice demonstration.. I have a right-hand drive version.. I believe the shafts are similar to the left-hand version you're using in the video? I'm abit confused.
My front wheel does not have the hole so you have to remove the bearing Nutt with the wheel off. To do this I tried it in gear but then changed my mind so I put an Allen key into the disc and had it against ythe calliper with a scaffold bar to undo it
Brilliant Videos, I have acquired 307 2003/4 not sure of the engine capacity buts its been well refurbished, however when I turn on the A/C the temperature shoots up to the red, Please any ideas on the cause?
Hi Sulei, Sounds like cables or panel malfunctioning. Can you regulate the temperature at all or is it only in the auto mode? If the second one, it can also be the temperature sensor. I would start from checking the cables with multimeter. Cheers!
The left hand side was a nightmare for me the drive shaft itself won't go all the way in the right hand side was easy the left for some reason I have a gap between the gearbox/seal to the driveshaft of about 10mm the old one sat a lot closer but its not leaking oil maybe it because it was not a oem part
@@jj-ue4eb 407 1.8 petrol year 2009. i put new clutch in in 2021 had a leak since then so fitted new one today, no memory of seeing snap ring today or in 2021, now hoping it's just spill from top of gearbox i spilled when filling from top vent. other wise i was thinking leaking cause shaft sliding in and out of box
I will add that to the list - no problem. I cannot promise it soon but in the meantime you can have a look here: ruclips.net/video/yxESGM06kYY/видео.html Hope it helps Cheers!
pezo 307sw 1.6hdi.All the best I am from Serbia and the master would charge about 50euros for hand without parts.Thanks to you,I did everything myself and took my wife and children to meal and movie.
Big thanks for these tutorials, i also watched the trans oil change in addition to this. Just as a note, the 307 that i was working on had somewhat of a "weird" transmission casing. The drain plug was on the side of the casing like it is on some other 307s i've seen rather than in the front side like in this video. But the fill plug was about where it is on your car and the venting hole had just a plastic cap that pulled off instead of threaded plug. Got the job done though, was a bit easier than i first thought.
Great clear and easy to follow video, thanks for the time spent helping others
Best Video i have found on 307. Thank you so very much.
is there no snap ring on left hand side driveshaft going into gearbox, if not how does it stay in place, thanks
Can this cause abs failure?
As my abs lights turns on above 45 50mph,.and works normally if i switch car off and on again and its making a clunk noise from that side
Clunk clunk sound while breaking with abs on, and no clunking when abs deactivates and warning light on in dash.
Are these seals actually on the gearbox it's self and would it be better to change them if replacing a gearbox . Before replacement box goes bck in
Nice demonstration.. I have a right-hand drive version.. I believe the shafts are similar to the left-hand version you're using in the video? I'm abit confused.
I hope you got the tracking done after this
My front wheel does not have the hole so you have to remove the bearing Nutt with the wheel off. To do this I tried it in gear but then changed my mind so I put an Allen key into the disc and had it against ythe calliper with a scaffold bar to undo it
I need your help i need the support bearing size for the cv jiont in the middel and this oil seal size please
Brilliant Videos, I have acquired 307 2003/4 not sure of the engine capacity buts its been well refurbished, however when I turn on the A/C the temperature shoots up to the red, Please any ideas on the cause?
Hi Sulei,
Sounds like cables or panel malfunctioning. Can you regulate the temperature at all or is it only in the auto mode? If the second one, it can also be the temperature sensor.
I would start from checking the cables with multimeter.
Cheers!
The left hand side was a nightmare for me the drive shaft itself won't go all the way in the right hand side was easy the left for some reason I have a gap between the gearbox/seal to the driveshaft of about 10mm the old one sat a lot closer but its not leaking oil maybe it because it was not a oem part
Does the left side shaft have a snap ring to hold in place in transmission
did you find out, i just put new seal in dont remember snap ring not sure yet if leak is fixed
Which model are you working on. The left hand side drive shaft does not have a inner circlip. It's held in with a spring that is inside the garter.
If the shaft came out easily after removing the hub it doesn't have a clip
@@jj-ue4eb 407 1.8 petrol year 2009. i put new clutch in in 2021 had a leak since then so fitted new one today, no memory of seeing snap ring today or in 2021, now hoping it's just spill from top of gearbox i spilled when filling from top vent. other wise i was thinking leaking cause shaft sliding in and out of box
@@jj-ue4eb it's left hand shaft i worked on
Did I hear u say that the right side seal is larger? Think the left side is larger
Hi. Pleas number of new seal. Thank you.
Could you be kind to share changing Transmission Oil for Automatic 307 style 1.6 as well? Many thanks.
Jak już wysiliłeś się na angielskiego lektora to serce boli liczba wyświetleń! Zmień również opis!
Also my new drive shaft the intermediate bearing was thinner then the original
Is this automatic or manual gearbox ?
Yeah I think so we're u put water in for your radiator
I will add that to the list - no problem. I cannot promise it soon but in the meantime you can have a look here: ruclips.net/video/yxESGM06kYY/видео.html
Hope it helps
Cheers!
Great video can you a video on how too drain water out off the engine and bleeding and also how too take out the expansion water tank thank 🙂
Thanks Mohammed,
Do you mean the coolant reservoir?
Cheers
you need to change brake disc too
Thankyou good help.
Thanks for tutorial ..but i have pug 307 sporty ..succes..
You are welcome ;)
hi thank you for this vedu so much
You are very welcome Zead :)
GRACIAS TOTALES ....
Is it a common fault at this model
Should of undone the lower control arm
Перевести на русский