I think your slm videos are educational. Thank you. I have a question. I don't want to spend on my cordless drill and buy a new adapter or tarsformer. It's expensive. Can I convert my 12V, 2A adapter to 14.6V and 20A, I need your information, thanks
It's impossible. The power of your present PS is 12*2=24W. Whereas you ask 14*20=280W. It looks like to hope a child 5 years old to carry a 100kg weight. You should buy a more powerful PS. Sorry, this section is Turkish: Sonradan farkettim, soru soranın adı Türk olduğunu kanıtlıyordu. Herneyse, yukarıdaki lafın özeti 3 kuruşa 5 köfte olmaz. Sen herhangi bir güç kaynağının akımını veya gerilimini artırıp azaltabilirsin ama gücünü yükseltme olanağın yok.
@@asifshahsyed422 sure. that resistors limits load current but under constant voltage. according to differences of the work or test, you can use vary values. if the R is big so the current goes lower and R is less, current is much more than first one. i always prefer less current not to break down something
so i understand that the voltage range is 3to 32v? how can i make with higher voltage range? what about amp? how i control the current so is this setup can work with powerful led 30w or higher? i need to build one that i can use it to test single leds or strip with any voltage upto 100v for example and i will install voltmeter and amp meter to know the voltage and current suitable for the led is it possible?
Any white led draws 20mA maximum but this ps you build, can give 45 mA current at 34V (ideally 24Vac transformer gives 24*1.41=33.8Vdc) output and with totally 660 ohm serial resistors that this current is harmful for ordinary single led.
Jee laga skty hain , dono resistors ail sath positive side pe laga den black probe ko direct negative pe voltmeter ki negative bhi, red prob aor voltmeter ki positive ko dono resistor ke baad la len
Is it possible to add a DC volt and ampere digital display in this circuit. If so kindly provide the sketch for this addition in the circuit. Really an interesting and useful circuit you have uploaded. Thanks a lot.
Have a nice day Mr. Tariq. Honestly, among the videos I watched on LED testers, it was your LED tester that I chose to do. But the transformer I bought is 18-0-18 Volts and not like your 12-0-12 Volts transformer. Question: do I always keep the same values -capacitors (50V, 1000 microfarads)? - the 2 resistors (2×330 ohm)? Thank you to answer me to start testing my LED.
Nice video🙂👍, i want to ask. What will happen if we accidentally short positif probe and negatif probe. Will the capacitor explode or the transformer burnt?
Why use resisters?you use 12-0-12 .bridge that means 24v coming .that time you use resisters drop the voltage .how to check led lights and black lights ? Not show perfectly.
Good evening Mr. Tariq Thank you, I have already built an LED tester of this type, it works properly, however I still have a few questions: 1- Is it possible to get rid of the capacitor? If not, what is its role in this LED test? 2- Since we used a diode bridge which rectifies the alternating current into direct current, why then use a transformer since the diode bridge is enough when we can weld two diacs between the positive and negative terminals of the diode bridge. Thank you.
An LED tester that tests SINGLE diodes uses a 9 Volt block battery , with a 680 Ω resistor in series with one of the probe leads ... portable , for use in your tool bag ! ! ... ( tried - n - tested ) ........ DAVE™🛑
What is the capacitor value? If you provide the components list it will be nice.
1000uf 50v
So lovely to learn .......so nice music, which is flow ing and understand your new knowledge......so....
You are doing great job
Thanks again for your help
For higher voltage can We use voltage multipley circuit
Thanks for your video! Can I test a 94v strip with this set up? If not what is the highest voltage I can go?
U can test start to half strip or single led, otherwise u have to use higher transformer 60v
Can i use a 24V trafo without a centerpin?
Yes
خیلی عالی متشکرم فقط مشخص نشدچیپLED هم روشن میکنه؟ اتصال کوتاه داره؟ویامیشه ولت مترنصب کردکه ولتاژهرکدام لامپ رابشه دید یانه؟ممنون میشم اگه جواب بدید سپاس❤❤❤
is it ok to use GBL 405 BRIDGE rectifier IN PLACCCE OF BGL 406 rectifier
Yes
Thank you so much! I can not wait to start setuping. I want to create original soft for comrcials and shows alongside my many other
Nice. Thank you.
I think your slm videos are educational. Thank you. I have a question. I don't want to spend on my cordless drill and buy a new adapter or tarsformer. It's expensive. Can I convert my 12V, 2A adapter to 14.6V and 20A, I need your information, thanks
It's impossible. The power of your present PS is 12*2=24W. Whereas you ask 14*20=280W. It looks like to hope a child 5 years old to carry a 100kg weight. You should buy a more powerful PS.
Sorry, this section is Turkish:
Sonradan farkettim, soru soranın adı Türk olduğunu kanıtlıyordu. Herneyse, yukarıdaki lafın özeti 3 kuruşa 5 köfte olmaz. Sen herhangi bir güç kaynağının akımını veya gerilimini artırıp azaltabilirsin ama gücünü yükseltme olanağın yok.
@@gundogankazanc9241hello sir can we use other than 330 ohm resistor???
@@asifshahsyed422
sure. that resistors limits load current but under constant voltage.
according to differences of the work or test, you can use vary values. if the R is big so the current goes lower and R is less, current is much more than first one.
i always prefer less current not to break down something
@@gundogankazanc9241 thank you
so i understand that the voltage range is 3to 32v?
how can i make with higher voltage range?
what about amp? how i control the current
so is this setup can work with powerful led 30w or higher?
i need to build one that i can use it to test single leds or strip with any voltage upto 100v for example and i will install voltmeter and amp meter to know the voltage and current suitable for the led is it possible?
Increase the value of resistors
@@TARIQLAB if i increased the resistance what will happen?
Any white led draws 20mA maximum but this ps you build, can give 45 mA current at 34V (ideally 24Vac transformer gives 24*1.41=33.8Vdc) output and with totally 660 ohm serial resistors that this current is harmful for ordinary single led.
How many volts out put of transfrmr.pl tell
What is the value your capacitors?
1000uf 50v
Tariq bhai me isme digital volt meter lga skta hn? Agar haan to kahan or kese. Mere pass 2 wires ka digi meter he
Jee laga skty hain , dono resistors ail sath positive side pe laga den black probe ko direct negative pe voltmeter ki negative bhi, red prob aor voltmeter ki positive ko dono resistor ke baad la len
@@TARIQLAB JazakAllah bhai. Me kr k btata hn
How many amperes does the transformer have?And also the wattage of the resistor?thanks in advance
Transformer 1A resistors 1W
Very Nice Job Sirjee......
Welcome
but how the voltage value change automaticaly ?
Due to the resistor,
@@TARIQLAB but the resistor value is fixed bro , can you explain in more details , thank you
if I add a voltmeter to the circuit, can I use it as a zener diode tester?
Yes
HOLA SOY UN FANATICO DE TU CANAL DEJAME DECIRTE QUE SOS UN GENIO SALUDOS DE JUAN DE ARGENTINA CUIDATE HERMANO TE RECONTRA FELICITO
de nada muchas gracias
can we use 32 0 32 transformer?
Use only two wires one center other side
Can you suggest me another bridge rectifier instead of this
U can use 4 diodes
Una pregunta las 2 resistencias son de 330 ohmios ??
Yes
@@TARIQLABcan we use other than 330 ohm resistor
Esallamo 3alaycom nice and good work proftionall thank you very much teacher and good luck 👍👍👍
Good 👍👍👍
hello sir,,,, can you make a video,,,,,a backlight tester using a circuit of long tube light bulb ,, thank you
Bạn cho hỏi ,tôi có vol kế 3 dây ,vậy hàn vô đầu nào và như thế nào
+ mắc cực dương tụ - mắc cực âm tụ, dây chuẩn thứ 3 sau điện trở
Sau điện trở mà ỡ chân +hay - ,cám ơn bạn nhiều
How to connect volt and ampere meter to this one.
I´m a bit confused cause the colours of the resistors you are using doesn't seem to indicate 330ohm value do they ?
330 ohm
Yes I have seen thanks 😊
Sir what is the value of condenser
1000uf 50v
12 0 12- 1amp transformation aur 330ohms resistance use kiya lekin LED jalta nehi kyu.
Probe pe kitna volts hai 30se oper hona chahiye
Can I use 220 Ohm resistor? It cause any damage?
No problem
@@TARIQLAB thanks for reply sir
Transformer kitne amp's ka hai ?
1 amp
thank you TARIQ LAB . . .. mabuhay !!!! jun mozo, davao city- philippines
Thanks a lot Tariq bhai
Good Bhai Ji,👏👏👏👏👍
Nice video, thanks :)
Good 🎉❤🎉❤
Good 🙏
Nice project brothers🙏
Is it possible to add a DC volt and ampere digital display in this circuit. If so kindly provide the sketch for this addition in the circuit. Really an interesting and useful circuit you have uploaded. Thanks a lot.
Visit my channel
Have a nice day Mr. Tariq. Honestly, among the videos I watched on LED testers, it was your LED tester that I chose to do. But the transformer I bought is 18-0-18 Volts and not like your 12-0-12 Volts transformer.
Question: do I always keep the same values
-capacitors (50V, 1000 microfarads)?
- the 2 resistors (2×330 ohm)? Thank you to answer me to start testing my LED.
Increase resistors to around 420 ohm and better to use 63v capacitor
@@TARIQLABthank you very much Mr. Tariq.
Your brother from Tunisia.
No, less than 60v no problem
Sir transformer Amp..???
Nice video🙂👍, i want to ask. What will happen if we accidentally short positif probe and negatif probe.
Will the capacitor explode or the transformer burnt?
Nothing, may be resistors blow if u short for some time
@@TARIQLAB thank you for your information 👍🙂
Nice idea. Thanks.....
Superb Project 👌👌👌👌👌👍
thank you for sharing this with us!!!
Well done!
It is better to add a DVM (digital voltmeter) to your design.
Thank you,
Voltmeter added in my other designs
Higher voltage Led series will not work with this output voltage like the 9 watts led bulb with 9 Volt led each so total 80 volt required
I am a new subscriber today.. I'll try to make one of ur project.. thank u and more power.. buenas dias
Why you didn't Using digital volt meter?
Won't the current drop for each led that's driven by this?
Kreatif good
Nice sir👋
Transformer kitana amp ka ha
2A, ap 1A ka bhi use kar sakty hain
@@TARIQLAB 750 amp ka chal jayaga kya
Yes
Sir capacitor ka number bataiye please
Filter capacitor hai, 1000uf ya 2200uf 50v
Nice video.what is the wattage of two resistors used?
1/2 watt
@@TARIQLABhello sir cam we use resistor other than 330 ohm
If I had put a voltmeter it would have been top,👍🇧🇷
good information from Saad electric
Why use resisters?you use 12-0-12 .bridge that means 24v coming .that time you use resisters drop the voltage .how to check led lights and black lights ? Not show perfectly.
Resistors drop voltage and amp according to load
sir what is the Value of condencer
1000uf 50v
Good evening Mr. Tariq Thank you, I have already built an LED tester of this type, it works properly, however I still have a few questions:
1- Is it possible to get rid of the capacitor? If not, what is its role in this LED test?
2- Since we used a diode bridge which rectifies the alternating current into direct current, why then use a transformer since the diode bridge is enough when we can weld two diacs between the positive and negative terminals of the diode bridge. Thank you.
Capacitor is a filter capacitor to smoothing the DC voltage.
IJust be seeing this connection
Would you please draw it with another of thanks
Super
Thanks
The 👌 video
Is that correct or no?
whats the cap size please
1000 uf 50v
Sir if I put a volt meter will it show the vote
Yes , normally it will show total volts 48V , but when u check led will show the eld voltage.
Can Sir Resistor Cotter Watt be used?
capacitor vallue not mentioned
1000 or 2200 uf 50v
Sir Resistance value tell me
330 ohm
Thank you sir
What was the value of capacitor??
2200uf 50v
Can I have the circuit diagram of it and the layout?
@@TARIQLABsir 12 0 12v 3amp use kar saktein ha I kya
ينفع محول 9فولت
Yes, use 33 Ohm resistors
Are you sure this resistor is 330♎?
Color is invisible
Yes
@@TARIQLAB thanks,
Amazing video, Thanks a lot TARIQLAB
Nice work
Input 220 v output...?AC
12+12=24v ac when converted to dc 36-40v, its 12v center tapped transformer, don't use center wire
@@TARIQLAB thnks ❤ brother
Won’t the Leds fuse
Safe for all LEDs
Good
Great work.. but I hope you delete the singing clips from the videos you publish and settle for the music only 😘
Noted
since there are 36 volts at the tip of the tester, why doesn't the led burn?
I used Resistors , voltage and current drop
@@TARIQLABtank's
I built this project. worked perfectly. I was looking for a led tester. Thanks.
Nice 👍🏻👍🏻 🇮🇳 Kuki 30|08|2022
37V/660ohm=0.056A=56mA Too much current.
The resistor needs to be increased to 2k ohm.
Then not possible to test 32v led backlight strip. With this arrangement u can test 3v-32v led
An LED tester that tests SINGLE diodes uses a 9 Volt block battery , with a 680 Ω resistor in series with one of the probe leads ... portable , for use in your tool bag ! ! ... ( tried - n - tested ) ........ DAVE™🛑
Resistor ?????
330 Ohm
The Cool...
Stay blessed 🙌
Thank.... Let'snext brother
Yes like this one want digital volt meter in it
Wait for next video
@@TARIQLAB okay thanks 😊
One question: and the Diagrama?.
Only diode capacitor & resistors, very simple
بھای آپ اس میں میوزک نہیں ڈال کرو اس سے آپ کو گونںھا ملتا ھے
Put led meter also
Noted
👍👍👍
there's absolutely no way you're going to test single leds with 24v they'll blow up. some of them are 3v or less
Why i used resistors
909 me bana sakte hai bhaiji
909 kiya?
@@TARIQLAB 909 ke trasfarmar se bana sakte hai LED tester
Jee
That resistors is not 330 ohms
In video may u see different colors
Transformer 1amp 12 0 12 sir 💐🙏
Yes
ভাই, কথা বলতে হবে নাহলে নতুনযারা তারা বুঝবেনা।
🙏❤️👌👌👌👍✋
1:40
Yes
كام اوم الريزستور
330 اوم