Good video! Just for info though - When you initially connect the battery and get a reading, the 'Current Capacity' and 'Health' when you click the buttons for the first time will show when the battery was last charged (it holds it in memory). When you go through the process of one of the other tabs, lets say Repair process, when you go back the the first screen (Battery Info) and click 'Current Capacity' and 'Health', you will get the updated status of the battery. Generally it will be much lower than when you first checked it. I've started uploading photo's of different pin layouts for various batteries in his new forum on his website by the way. Hope to see some of your photos there too! :)
Dell D600 battery (C1295) With a jumper between Ground and the SYS PRESENT pin I can measure voltage and discharge the battery using a R/C charger /discharger. However I can not charge at the out most pins. No current flow goes into the battery. If I put the battery back in the laptop it will charge it full again. Would you know if I need another jumper to allow the battery to accept charging?
Boa noite ! Essa ferramenta também pode reviver as baterias do laptop que estão descarregadas demais, mas ainda não travadas (as baterias que são armazenadas por um longo período sem carregar)? Pois eu pesquisei um outro modelo o ( testador Rfnt3 ), mais o que pude perceber é que ele só passa a informação da bateria. Já o NLBA tem mais funções.
Internal resistance is no real measurement of a battery. In fact, according to cadex, the world leaders in battery analysis, it can give false readings. Go and read batteryuniverse, the process of testing any battery is far more complex than this machine would have you believe. A ‘stab in the dark’ resistance test could render a good battery as bad. An expert opinion is this The resistance of modern Lithium-ion remains low while the capacity gradually drops. Resistance measurements alone do not provide reliable results. The correct test is this Developed by Cadex, QuickSort™ uses electrochemical dynamic response to check the flow of ions between the cathode and anode of Li-ion. A digital load simulating a mobile phone excites the battery and the generic matrix classifies the battery into Good, Low and Poor. The test takes 30 seconds, is 90% accurate over a broad range of Li-ion systems and can be performed with a state-of-charge of 40-100%. The system does not rely on internal resistance as this would produce unreliable readings. Modern Li-ion keep low resistance with cycling, and Figure 2 illustrates this relationship.
Наука
Bought one of these, came within a day or two, great product.
Good video! Just for info though - When you initially connect the battery and get a reading, the 'Current Capacity' and 'Health' when you click the buttons for the first time will show when the battery was last charged (it holds it in memory). When you go through the process of one of the other tabs, lets say Repair process, when you go back the the first screen (Battery Info) and click 'Current Capacity' and 'Health', you will get the updated status of the battery. Generally it will be much lower than when you first checked it. I've started uploading photo's of different pin layouts for various batteries in his new forum on his website by the way. Hope to see some of your photos there too! :)
The correct FCC (Full Charge Capacity) will be shown after a calibration cycle 0% to 100% then back to 0%.
Dell D600 battery (C1295) With a jumper between Ground and the SYS PRESENT pin I can measure voltage and discharge the battery using a R/C charger /discharger. However I can not charge at the out most pins. No current flow goes into the battery.
If I put the battery back in the laptop it will charge it full again. Would you know if I need another jumper to allow the battery to accept charging?
Boa noite !
Essa ferramenta também pode reviver as baterias do laptop que estão descarregadas demais, mas ainda não travadas (as baterias que são armazenadas por um longo período sem carregar)? Pois eu pesquisei um outro modelo o ( testador Rfnt3 ), mais o que pude perceber é que ele só passa a informação da bateria. Já o NLBA tem mais funções.
Yes, it can do that if the battery is still not locked.
I want to buy it but it's not longer available
hello do you have a password for the software please?
The software does not need any password.
Internal resistance is no real measurement of a battery. In fact, according to cadex, the world leaders in battery analysis, it can give false readings. Go and read batteryuniverse, the process of testing any battery is far more complex than this machine would have you believe. A ‘stab in the dark’ resistance test could render a good battery as bad. An expert opinion is this The resistance of modern Lithium-ion remains low while the capacity gradually drops. Resistance measurements alone do not provide reliable results. The correct test is this Developed by Cadex, QuickSort™ uses electrochemical dynamic response to check the flow of ions between the cathode and anode of Li-ion. A digital load simulating a mobile phone excites the battery and the generic matrix classifies the battery into Good, Low and Poor. The test takes 30 seconds, is 90% accurate over a broad range of Li-ion systems and can be performed with a state-of-charge of 40-100%. The system does not rely on internal resistance as this would produce unreliable readings. Modern Li-ion keep low resistance with cycling, and Figure 2 illustrates this relationship.
hello do you have a password for the software please?
The software does not need any password.