Thanks so much for doing this video. I was finally able to get Carplay working on my OAP/RPi-4B setup after I watched your video. My Carlinkit dongle also had USB Device ID 1314:1521. Per your instruction, I edited the product ID under [Autobox] from 5408 to 5409, and this resolved my issue. A big shout out to you !!
@@apprenticeDoingTech Thanks again for your help. I am struggling to get FM radio with my RPi4/OAP setup. I got the RTL-SDR V4 but welle*io does not identify the device (no device found in 'expert' mode). I even downgraded to the RTL-SDR V3 but still no luck. I would love to try the OAP plug-in for FM but cannot since the shutdown. Did you get FM to work in your setup? Thanks in advance for any insight you can give.
@@oiuy8p520 Didnt know that. I will look around maybe i am able to find the fm plugin somwhere. Sadly DAB+ will not be available in OAP. Maybe using welle io and a data sim in the pi could also do the trick
Thank You Very Much! I will likely buy into this and the community once I get my other big project done. The area I have to study is the API to integrate CAN communications for my engine.
I need the Raspberry Pi 5 to work in my car for my university project, so I watched your video for possible solutions. I powered the Pi using an XY3606 buck converter, stepping down from 12V to 5V with a 6A output. The USB-C cable I used supports up to 6 amps, so I cut the cable and connected it directly to the 5V and ground of the XY3606. However, I’m still getting a warning on bootup saying insufficient power. I also tried connecting it directly to a variable power supply in the university lab, adjusting it to 5V, but the same issue occurs. Any solutions?
Servus Christian, hast du OpenAuto noch auf der Bluewave Seite bekommen? Weil da kann man aktuell nichts mehr runter laden. Kannst du mir evtl. die Datei zuschicken? Beste Grüße Sebastian
is there a way to install just the open auto as an image without it being over raspian. Seems like inefficient use of the hardware as i feel like raspian wont be used very often.
@@apprenticeDoingTech ok thanks. I have been looking at the options and I think that I can't decide between this and open dash. I think open dash is a lot smoother but this one seems to be more popular.
@@jakewynn Ive ran openauto pro for a year on a pi 3 wich does the job but not always to quik . On the pi 4 im working on integrating can functions to set power and charge limits on my ev conversion. I dont think its the best out there but its really solid. Also i got the boot time to around 30s which is also not bad. If you go with openauto fell free if you encounter any issues
@@apprenticeDoingTech I’d quite like to change the layout and styling of the OAP install - probably an insane task for a new starter but I’m willing to give it a go !
So I have an older version of OpenAuto but cant get the update. Do you still have the image file? I already have a license key. just need the 16.1 image zip file.
Hey man, how are you? I lost all the OpenAuto Pro installation files. Could you make these files available? For some reason BlueWave took everything offline, nothing works, the download links, the website to order it and the purchase page are not available. Could you do this?
i installed it , but once the phone is connected it says android auto connected , but I see black screen on the raspberry pi. note: before i connect the phone i see open auto pro ui and can change settings etc. Do you know how to fix this?
@@dasari_manoj I had the same problem using OpenAuto 15.... try uninstalling Android Auto App on the phone and install an older version... For me version 12.6.6.... fixed the black screen problem. I'm not sure why newer versions won't work anymore but at least there is this solution for now
@@roxbinx4006 hey ich habe einen von waveshare links habe ich keine gepostet da ich mit keiner der Firmen assoziiert bin. Ist aber ein 11.6 zoll ips panel würde wegen der Helligkeit kein oled empfehlen hoffe das hilft
@@apprenticeDoingTech läuft das ganze zum Testen auch auf einem 3b wollte mir noch keinen 4er oder 5er kaufen solange ich nicht weiß ob es für meine Zwecke funktioniert
@@tjarktorp6741vor ca 2 wochen stand da mal was das es bald wieder kommt (out of stock). aktuell ist der shop 404. Das Update für pi 5 ist noch nicht da. Läuft auf dem 3er gut ist halt einfach etwas träge
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
Thanks so much for doing this video. I was finally able to get Carplay working on my OAP/RPi-4B setup after I watched your video. My Carlinkit dongle also had USB Device ID 1314:1521. Per your instruction, I edited the product ID under [Autobox] from 5408 to 5409, and this resolved my issue. A big shout out to you !!
Glad to help you. If you have any other problems im happy to help
@@apprenticeDoingTech Thanks again for your help. I am struggling to get FM radio with my RPi4/OAP setup. I got the RTL-SDR V4 but welle*io does not identify the device (no device found in 'expert' mode). I even downgraded to the RTL-SDR V3 but still no luck. I would love to try the OAP plug-in for FM but cannot since the shutdown. Did you get FM to work in your setup? Thanks in advance for any insight you can give.
Due to fm being shutdown here i havent tried yet. Sadly i dont have the plugin.
@@apprenticeDoingTech Yeah, FM still reigns here in the US. DAB+ is not a thing yet for us.
@@oiuy8p520 Didnt know that. I will look around maybe i am able to find the fm plugin somwhere. Sadly DAB+ will not be available in OAP. Maybe using welle io and a data sim in the pi could also do the trick
Thank You Very Much! I will likely buy into this and the community once I get my other big project done. The area I have to study is the API to integrate CAN communications for my engine.
I need the Raspberry Pi 5 to work in my car for my university project, so I watched your video for possible solutions. I powered the Pi using an XY3606 buck converter, stepping down from 12V to 5V with a 6A output. The USB-C cable I used supports up to 6 amps, so I cut the cable and connected it directly to the 5V and ground of the XY3606. However, I’m still getting a warning on bootup saying insufficient power. I also tried connecting it directly to a variable power supply in the university lab, adjusting it to 5V, but the same issue occurs. Any solutions?
Yea there are multiple options. Have you tried feeding it 5.2-5.3V? Did you use propper pd controller?
@apprenticeDoingTech i have only used reguar usb c cable and yes, i tried 5.2v
Is it possible to use an dac hat for the raspi audio output?
Servus Christian, hast du OpenAuto noch auf der Bluewave Seite bekommen? Weil da kann man aktuell nichts mehr runter laden. Kannst du mir evtl. die Datei zuschicken?
Beste Grüße Sebastian
Leider nicht das das piracy wäre
Aber ich bin am schauen evtl krigt man das ja ge opensourced?!
💀
Fuck yeah, struggling anyway but my day just got better.
PS: First comment on your first video, keep going!!
Where can I download the image of Open Auto Pro please ?
Can the camera auto start when the car is put into reverse? Does this integrate with odb2 in any way?
@@adzza83 it can be started over a GPIO pin so you would need to run an extra wire. I don’t know an other way to do it.
How do you get OpenAuto Pro i cant find a download for it
Currently nowhere
But you can try asking nice here
christian.obrecht@icloud.com
same problem =(
Just write me an email
@7276155 let me know if you were able to download it
@@apprenticeDoingTech Where to write you an email. I cant find your email address in the description or any where else...
is there a way to install just the open auto as an image without it being over raspian. Seems like inefficient use of the hardware as i feel like raspian wont be used very often.
I have tried but it depends on may drivers and systems of raspian so currently not possible
@@apprenticeDoingTech ok thanks. I have been looking at the options and I think that I can't decide between this and open dash. I think open dash is a lot smoother but this one seems to be more popular.
@@jakewynnin my experience openauto is somtimes a bit finicky but on a pi 4 it is quick and really reactive.
@@apprenticeDoingTech which one would you recommend? Which do you use on a daily basis?
@@jakewynn Ive ran openauto pro for a year on a pi 3 wich does the job but not always to quik . On the pi 4 im working on integrating can functions to set power and charge limits on my ev conversion. I dont think its the best out there but its really solid. Also i got the boot time to around 30s which is also not bad. If you go with openauto fell free if you encounter any issues
currently building my own too ! have you got any advice on editing the UI ? I'm a total linux n00b so struggling past the config files !
What do you want to modify?
@@apprenticeDoingTech I’d quite like to change the layout and styling of the OAP install - probably an insane task for a new starter but I’m willing to give it a go !
@@tiimhughes you can change a lot in the settings
@@apprenticeDoingTech for sure ! I mean more than the settings menu - would really like to move items, remake all icons, change grid etc !
@@tiimhughes have fun😉
I have not finished setup my carplay system and the website is down... how to move forward?
@@wkl3968 so react CarPlay could work for you
Cranckshaft is also an option or just use lineage os for pi and install apps on it
Hi,
where did you get the image file, i m looking for it on the official website, but it seems not availabel anymore.
Currently the shop is down i don’t know what’s up with that.
@@apprenticeDoingTech sad, where can i buy it?
@@JS-hk7tc i sent them an email and asked. It would be bluewave studio
@@apprenticeDoingTech Thanks, if there is some news pls tell me.
Hoffe kommen noch mehr videos, bin auch am überlegen mir solch ein System zu installieren.
Ist geplant werde meine installation präsentieren. Falls bei dir probleme auftauchen melde dich. Dann kann ich vielleicht helfen
thanks for the tip on the camera!
Dont forget that the pi isnt 12V tolerant 😉
Great music taste ;)
Where did you buy that screen?
Got it from www.waveshare.com
So I have an older version of OpenAuto but cant get the update. Do you still have the image file? I already have a license key. just need the 16.1 image zip file.
Sure write me a mail on christian.magnus@obrecht.ch
Hey man, how are you? I lost all the OpenAuto Pro installation files. Could you make these files available? For some reason BlueWave took everything offline, nothing works, the download links, the website to order it and the purchase page are not available. Could you do this?
@@wellingtongna yea idk about the legality of that even though its still keyed but you can write me an email christian.obrecht@icloud.com
i installed it , but once the phone is connected it says android auto connected , but I see black screen on the raspberry pi.
note: before i connect the phone i see open auto pro ui and can change settings etc.
Do you know how to fix this?
@@dasari_manoj sadly not im not experienced with android auto i tried i once and it worked for me
Thanks for the response, I'll try carplay , hopefully it works.
Just sent an email , hoping you could share how the plug-in
@@apprenticeDoingTech 1 time i got below error : unable to open mtp device 001,006
tried different cables as well same issue
@@dasari_manoj I had the same problem using OpenAuto 15.... try uninstalling Android Auto App on the phone and install an older version... For me version 12.6.6.... fixed the black screen problem. I'm not sure why newer versions won't work anymore but at least there is this solution for now
Hey, sehr cool habe jetzt endlich ein gute Lösung gefunden CarPlay nachzurüsten... welches Display hast du dafür benutzt? Hast du vllt ein Link?
@@roxbinx4006 hey ich habe einen von waveshare links habe ich keine gepostet da ich mit keiner der Firmen assoziiert bin.
Ist aber ein 11.6 zoll ips panel würde wegen der Helligkeit kein oled empfehlen hoffe das hilft
Welche Seriennummer braucht Openauto und wovon? Aber an sich ein Hilfreiches Video
Es ist ein product code von bluewavestudio wird beim Setup Seriennummer genannt. Den Bekommst du wenn du OAP bestellst
@@apprenticeDoingTech Achso good to know, leider momentan nicht verfügbar, aber es kommt bald wieder
@@RealTWesshoffe das kommt bald wieder das system ist echt gut
Hey bei mir scheitert es schon das ich keinen download link für open auto finde
Es scheint so alsob bluewave studio den shop erneuert. Man bekommt den link zum download nach der Bestellung.
@@apprenticeDoingTech zurzeit kann man nicht kaufen oder hast du einen Kontakt?
@@apprenticeDoingTech läuft das ganze zum Testen auch auf einem 3b wollte mir noch keinen 4er oder 5er kaufen solange ich nicht weiß ob es für meine Zwecke funktioniert
@@tjarktorp6741vor ca 2 wochen stand da mal was das es bald wieder kommt (out of stock). aktuell ist der shop 404.
Das Update für pi 5 ist noch nicht da. Läuft auf dem 3er gut ist halt einfach etwas träge
Thank you, I sent you Message 😇
Im sorry its gonna take until next week before i can help you
@@apprenticeDoingTech Thank you once more for swift reply,when you have time will be gladly receive yur respons.
@@apprenticeDoingTech another message to you bro😊
Hello, from where can I download it? I also send you the email