FREE Pulley Swap with a Welder. The FREE OFF-ROAD MOWER gets MUCH FASTER.
HTML-код
- Опубликовано: 5 фев 2025
- Making a lawn tractor mower fast by altering the drive ratio of the engine and transaxle pulleys. Using stock original parts, a hole saw, and a welder to swap the engine pulley to the transaxle and the transaxle pulley to the engine.
Contact Gary. garydeyo302@gmail.com
Sup lil Elon.. I’ve learned a trick or so from you. So buddy try the one tip I gave you. SLOTED ENGINE MOUNT HOLES. Just a lil slide help a lot.. Digging your videos pimp.
@richardyoung6496 Hahaha. Thank you. I appreciate you watching. I forgot about your slotted engine mount suggestion. That's definitely worth doing. I'm familiar with the concept. My childhood go-kart was like that, as I'm sure most are. Thank you for reminding me. That would really help with belt wear over time.
You’re right it’s okay for slow speed. I have a 93 that is like that works great,you’ll need a mule drive like a lot of mowers used for the deck. Speed cost money how fast do you want to go 🤣🤣. Give me a mailing address and I will see what help I can do. I have eight or ten little garden tractors I play with at 58 your never to old.
AND Never Throw anything away 🤣!! You never know what little part may save the day. Trust me when you do get it right nothing feels better. Also check out some Cycle karts I think that may give you some ideas.
Don’t give up! Henry Ford was in his 40s when he came out with the model T . GODS SPEED .
You should put a horizontal shaft engine and lower it great try so far
@@matthewanderson7766 Thanks. I think that's gonna be the route I take with it.
I'd like to see you start a gofundme so you could get ahold of a Predator V-Twin. At the very least, keep your eyes open on marketplace for a horizontal v-twin and build with that. Twisted belt setups, even when working, are a compromise at best and introduce mechanical complexity into your builds that kind of goes against the grain of your channel - simple fairly easy builds.
@LazloNQ I'm always on the lookout for engines. Horizontals are definitely harder to come by. I have an old opposed twin horizontal that I may try for now.
@@DieselFuelNetwork Yeah I heard you say that in your video. I'm not a fan of those boxers, preferring the sound of the v-twin, but you work with what you've got. I was thinking about this mower at work yesterday and I wondered if you could somehow fit a jackshaft under there that would align the belt from the engine to the jackshaft better and subsequently align the other end of the jackshaft to the transmission better? Still it's starting to get more complex and this design of mower doesn't lend itself well to being modded.
good video brother 👽💪
@@crumblyHawk Thank you
i liked the video. keep it up.
@@refugeinc.159 Thank you
I like to see you hook the tac and dial in the shifting and other upgrades great trial and error that's how you learn great video
@jreed2447 Thanks for your input. Those are definitely some things I want to do, and more. Thanks for watching
Very awesome my friend.
@@alanstant9356 Thank you
Nice work
@@thomasguerin765 thank you
Thanks!
😁😁👍👍Thank you. I really appreciate that. And you're welcome. 🚜💨💨💨
That's Awesome! Can't wait to Mod my GT 5000! Thanks for the Great Video!
@SteveM-426 Thank you. I appreciate you watching. There's definitely some challenges with modding these particular setups. Good luck with your project. 🚜💨💨💨
I'm not a big fan of twisted belt setups for the very reasons you discovered - it's not a good mower for this sort of conversion. Imagine using a Harbor Freight Predator V-twin with the horizontal shaft hooked to this transmission...it might just be grounds for the creation of hot rod tractor #2. You need a lathe of some sort...even if it's home made...it would help you immensely. Instead of needing cutting-bits, use an angle grinder to grind your stuff into submission. Thanks for sharing Gary!
@@LazloNQ I definitely have some ideas for it. No doubt, whatever this thing turns into, it will have a horizontal shaft engine of some kind powering it. I'm definitely lacking in the tool department. My ideas don't always match my skill or tool requirements. A lathe would be amazing.
When it comes to twisted belt drives, the part of the belt getting pulled on by the power source and where the belt comes off the driven pulley need to be inline. The non-torque side of the pulley can be at quite an angle but you do have to use guards to keep the belt on. I'm surmising when your belt is under load, it's pulling on the driven pulley at a pretty hard angle. With the pulleys in their original position, that angle was probably closer to straight. It's a whacky world when you're dealing with twisted belts. If you were to stretch this mower like you did with the hotrod mower, the longer path of the belt would help the situation because you're not pulling so hard of an angle over a relatively short distance. The farther apart the driver and driven is, the larger the angle can be, but you try to avoid any angles at all between driver and driven on the torque side of the belt.
@LazloNQ Yes, that's definitely the issue. At first, I figured it worked the other way, it should work the opposite way. But you're right. The original setup had almost no angle pulling from the crank to the trans pulley. It's now obviously pulling at a significant angle. I'm might do what I can to get it working, but ultimately, I'll probably be making some major changes with this machine.
It won't work unless you use pulleys to guide the belt and keep it tensioned.
@RollinMyOwn Yeah, it seems that way. The angle is so extreme.
@DieselFuelNetwork there's 1 other way...get a mule drive off s old garden tractor. It pivots 90 degrees...
@@RollinMyOwn I wondered if there was a 90 degree gearbox somewhere suitable for the purpose...
Yup j.d. 300 series mower deck mule drive
You need see carand cameras video them Good boy
YOU CAN NOT show welding on screen of the arc, IT WILL BURN peoples eyes, just keep something in between us and the arc, you go watch welding for hours or even a couple of minutes (sec) and it will burn your eyes, if you ,,,people feel ,,,like you have sand in your eyes,,then your eyes have been burned, ,please pay attention to the small stuff, eyes and vision is important, thanks BigAl California
@alkennedy1124 I'm not sure if you're joking or not. When welding, it is indeed very important to protect your eyes. However, what you're seeing on video is being reproduced by a screen that can not hurt your eyes. Thanks for watching, though. Sorry if I burned your eyes lol
You have got to be joking. What the camera captures and shows isn't harmful. In real life, sure you have to be careful, but worrying about watching welding on a screen? Who told you this?
Why didn't you put a piece of flat metal behind the big pulley to give it more reinforcements plus it would be a flat area that you can put the pulley the tension pulley wherever you would need it such as a crossmember for reinforcing the frame behind the engine just saying
what would the world do with out unsupervised man
@@mackandchezz Hahaha. nice, I like that. Thanks for watching