Get the red boots from MSD, they are high performance high heat boots. You probably have enough length to put them on your old ones. My grays burned through as well, this is what I am in the process of doing atm on my car, putting on the red spark boots.. Just a thought, like you said those MSD's are expensive, maybe you could have an extra set this way, that will not cause you the same problems. 90 degre boots PN# 8852, straights PN# 8854 and 115 degre PN# 8853. If these do not work for me I guess I may need to tray those Taylormade like you have. Happy Burnouts and Launches!!!!
On my 454, I got a standard set for I think it was an early 70's big block that came with 90 degree boots. Took a bit of digging to find me, but they work with headers.
Thanks for sharing I’ll be ordering plug wires a little later for my project. I was hoping to see your wheels and tires. I watched some of the videos on your frame notching. Back spacing and tire width. Thanks for sharing!!
Ya no problem man. My buddy started making vids on his build, mostly cuz you couldn't find parts or info on much of people showing wut or how to do certain things. And that's why I wanted to.
I thought you had gotten a set of rear wheels and then found out you could use more back spacing? I think I can get a 12” wheel with 6” back space on mine!! Thanks 🙏
I got a 15x10 with 4.5 backspace before I did notch. Had about a half inch of space. After notch i got jus a little over 1 inch of space now so i could run a 5.5 in backspace if i got another set of wheels. But where the wheel an tire sit now looks like its squared with the rear inner wheel well
Also where my wheel an tire sit it is flush with the outside quarter panel so it doesn't stick out. I'm gona drop the rear more cuz it sits really hi. Has like a 5 inch gap from tire to quarter panel.
Big Mo MonteCarlo ok thanks. Do ya have video where I can view the car ? Love that BBC . Mine is 468 just because I had some old parts. it’s a steel crank h beam rods with mahal pistons and balanced 10.5 compression. Like yours bet it will run! Thanks man I just an ole car nut!!
Headers are a problem even with engines moving around, I never even thought about burned wires. I like the regular exhaust manifold, there may or may not be any noticeable speed or power to my 68 350 Tempest with headers but I would like to quiet the exhaust more than extra power. Exhaust manifold goes straight into stainless dual exhaust to remove extra problems. I'm just getting 200 dollar pipes that connect the factory exhaust manifolds straight to the new duals, plus I replaced the original air cleaner to lessen the annoying exhaust more too.
ya. first a set of street fire wires. second was mad super conductor wires, now these Taylor's. these seem to be working alot better. probly gona pull headers n clearance certain primary's over winter
I picked a msd hei with taylor wires. I have the same boots but are 90 so some of the plugs lay on the header flange. I was wondering if they will burn or can the taylor boots take heat
They are about the same as the msd super conductor wires. Giving enough time they'll burn thru, but they last longer then alot of others. But i was also using the spark plug heat covers on them all.
I've always just run moroso 8mm with 90° boots. There like 40 bucks. And the heat shields to protect the wires I get from amazon 20 bucks for 8. Never have any issues. On my s10 that the po put headers on two are really close actually touching the plug boot so they will burn no matter what I do. For that I found pure ceramic ends there the same thing sinks and toilets are made from. Problem solved you can't burn those things with a touch got them from a website that sells parts for old model A hot rods and such. 12 bucks a piece but worth every penny.
I honestly think those boot covers are a joke. I have used them before and still had it burn thru boot to the wire. You might try to fatten the mixture at idle. I have noticed motor runs a tad cooler on the exhaust tubes.
I just ordered the MSD Multi-angle for my 1999 Suburban K2500 454 with headers. I was burnin up boots left and right. Hopefully the multi-angle function of the MSD boots remedy my situation. I like those Taylors too. If the MSD fails me I am going to go to 135 degree Accel Ceramic Boots. Something has got to work! Misfires all over the place.
Ya I hear ya man.. I jus had alot of problems with the big headers on the monte because of really tight clearences. I have to bend in the headers a little, or I'm thinking of making my own set of headers
Gotta be careful with those ceramic wires they work great with some plug but will slip off others. Also if box was dropped in transit the ceramic boot can arc directly thru the ceramic
Get the red boots from MSD, they are high performance high heat boots. You probably have enough length to put them on your old ones. My grays burned through as well, this is what I am in the process of doing atm on my car, putting on the red spark boots.. Just a thought, like you said those MSD's are expensive, maybe you could have an extra set this way, that will not cause you the same problems. 90 degre boots PN# 8852, straights PN# 8854 and 115 degre PN# 8853. If these do not work for me I guess I may need to tray those Taylormade like you have. Happy Burnouts and Launches!!!!
On my 454, I got a standard set for I think it was an early 70's big block that came with 90 degree boots. Took a bit of digging to find me, but they work with headers.
Thanks for sharing I’ll be ordering plug wires a little later for my project. I was hoping to see your wheels and tires. I watched some of the videos on your frame notching. Back spacing and tire width. Thanks for sharing!!
Ya no problem man. My buddy started making vids on his build, mostly cuz you couldn't find parts or info on much of people showing wut or how to do certain things. And that's why I wanted to.
I thought you had gotten a set of rear wheels and then found out you could use more back spacing? I think I can get a 12” wheel with 6” back space on mine!! Thanks 🙏
I got a 15x10 with 4.5 backspace before I did notch. Had about a half inch of space. After notch i got jus a little over 1 inch of space now so i could run a 5.5 in backspace if i got another set of wheels. But where the wheel an tire sit now looks like its squared with the rear inner wheel well
Also where my wheel an tire sit it is flush with the outside quarter panel so it doesn't stick out. I'm gona drop the rear more cuz it sits really hi. Has like a 5 inch gap from tire to quarter panel.
Big Mo MonteCarlo ok thanks. Do ya have video where I can view the car ? Love that BBC . Mine is 468 just because I had some old parts. it’s a steel crank h beam rods with mahal pistons and balanced 10.5 compression. Like yours bet it will run! Thanks man I just an ole car nut!!
Headers are a problem even with engines moving around, I never even thought about burned wires. I like the regular exhaust manifold, there may or may not be any noticeable speed or power to my 68 350 Tempest with headers but I would like to quiet the exhaust more than extra power. Exhaust manifold goes straight into stainless dual exhaust to remove extra problems. I'm just getting 200 dollar pipes that connect the factory exhaust manifolds straight to the new duals, plus I replaced the original air cleaner to lessen the annoying exhaust more too.
Sorry your having such bad luck with the wires hopefully you got it this time 👍🏻👍🏻 Cheers 🍺🍺
ya. first a set of street fire wires. second was mad super conductor wires, now these Taylor's. these seem to be working alot better. probly gona pull headers n clearance certain primary's over winter
I had Taylor wires and loved them until I had to remove them and half of the ends pulled off.
Will the 45 degree angles not do the job?
Good to know, thanks
Are those high heat zip ties?
I picked a msd hei with taylor wires. I have the same boots but are 90 so some of the plugs lay on the header flange. I was wondering if they will burn or can the taylor boots take heat
They are about the same as the msd super conductor wires. Giving enough time they'll burn thru, but they last longer then alot of others. But i was also using the spark plug heat covers on them all.
@@mcbluecollarguy2382 ok ill see if these will burn and go from there. I wish they were 135 but they cam with the dizzy.
I've always just run moroso 8mm with 90° boots. There like 40 bucks. And the heat shields to protect the wires I get from amazon 20 bucks for 8. Never have any issues. On my s10 that the po put headers on two are really close actually touching the plug boot so they will burn no matter what I do. For that I found pure ceramic ends there the same thing sinks and toilets are made from. Problem solved you can't burn those things with a touch got them from a website that sells parts for old model A hot rods and such. 12 bucks a piece but worth every penny.
what headers (model number ) are you running on your car ?
ny suff Hedman husler race headers 65 - 216
If your timing is to far off it could be firing out through exhaust
I am still running my big block
How did you fit the wires through the narrow boot?
What do u mean? Thru the heat wrap boot?
I'm having that problem now on my 383 stroker its one boot getting hot touching the headers
Ive watched engine master header challenge where they beat them in an it really doesnt show hp loss when denting in headers for clearance
I’m having the same problem with my 383 melting boots hopefully ceramic boots work
I honestly think those boot covers are a joke. I have used them before and still had it burn thru boot to the wire. You might try to fatten the mixture at idle. I have noticed motor runs a tad cooler on the exhaust tubes.
You do know the MSD boots are multiangle right? They can be bent so they do not touch the header.
These did not bend.
I just ordered the MSD Multi-angle for my 1999 Suburban K2500 454 with headers. I was burnin up boots left and right. Hopefully the multi-angle function of the MSD boots remedy my situation. I like those Taylors too. If the MSD fails me I am going to go to 135 degree Accel Ceramic Boots. Something has got to work! Misfires all over the place.
Ya I hear ya man.. I jus had alot of problems with the big headers on the monte because of really tight clearences. I have to bend in the headers a little, or I'm thinking of making my own set of headers
yes
Can a burnt wire cause your car to turn off
Yes, a burnt wire can crack thru an start arking off metal an shut car off. It gets coil so hot it doesnt wana run
I feel your pain, I been there I use accel 9000 ceramic booted and no more burnt wires
Gotta be careful with those ceramic wires they work great with some plug but will slip off others. Also if box was dropped in transit the ceramic boot can arc directly thru the ceramic
They are 8mm. Accel makes them already on the wire. They are bendable boots. $102.00 -8.5 mm.
nathan riley nice. thanks that's good to know for the future