Mazda remote keyless entry key DIY programming, keyfob only (DOORS ONLY)
HTML-код
- Опубликовано: 14 окт 2024
- Visit us at www.carandtruck...
Do it yourself Mazda keyless entry remote programming. Works for most Mazda remotes. One working key is required for programming.
THIS WILL NOT WORK FOR THE SMART KEY SYSTEM
NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
NOTE: Any existing key remote transmitters not used during programming will become inoperative.
Remove key from ignition switch.
Close all doors.
Open driver's door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Press and release driver's door courtesy light switch 3 times.
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver's door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Press and release driver's door courtesy light switch once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver's door already open.
2011 Mazda 2. Seven years ago my daughter lost the key and we had to use the spare. I found it a year later down the back of the couch. The buttons no longer worked. FOR SIX YEARS I have been manually locking and unlocking the car. SIX YEARS! I have no idea why this video came up in my feed at 1am as I was going to bed. But I just tried it and it works!!! Thank you!!!!
Thank you so much! This totally solved my problem where both my remotes stopped working! The people I talked to all said I should change the battery. After paying $5 to change one, nothing happened so I found your video when I googled the problem, did the steps at the same time as you, and it worked!!
I spent 2 hours doing this…and didn’t work pressing the UNLOCK button twice..I press the LOCKED button TWICE and it worked…I have a 2008 Miata…thanks for the video!
Happy to hear you were able to get it working!
This works!! It took a few moments to cycle through, but after that I am back in business! Thank you so much for saving me time and money!
Thanks for this video; it worked and now my wife loves me again! I tried a few times and the last time I skipped the 'lock and unlock door' step and went to the 'press the unlock on the remote twice' and it reprogrammed that time.
If anyone is having trouble getting their Mazda 3 into programming mode like I was at first, I discovered that, at least for my car, I had to additionally manually press lock/unlock on the driver's side door at the beginning after you open the door but before the key cycling. Every thing else as explained in this video worked great. Thanks!
Daniel MacDonald Some cars are a little quirky and require a few tweaks to the programming process. Glad to hear you got it working :)
My car wouldn't go into programming mode. I had to push my key inwards and hold it inwards the whole time to make sure it knew my key was in the ignition. After I did that it worked flawlessly. I've been trying to figure this out for years.
BumperPlates dude you're a life saver. After I held my key in, it finally works. Thank you veryone for the tips.
HOLDING THE KEY IN THE ENTIRE TIME FOR MAZDA 3 - THANK YOU 🙏🏻
Thank you!!
WOW! worked perfectly. Even the locksmith couldn't do it with his fancy gadgets, but this worked. I'm STOKED! Thanks (2010 mazda 6)
Thanks for you help. I'm in Western Australia and your RUclips video just worked for my son's 2009 Mazda 3 hatch in Nov 2020. Love it.
You're a genius, It was so simple to reprogram my Madza Protégé 5. I followed instructions to the letter and figured it out on the first attempt. You have no idea how much your video helped. I saved myself 100.00 dollars or more programming my own vehicle. Again, thanks alot.
Thank you so much bru, my key just stopped working after i removed the battery, tried ur instructions and it worked instantly.
Lost of words but thank you so much appreciate it
Worked great on my 2008 mazda 3. Was not a smart remote key, but never came with keyfobs. So an aftermarket keyfob and this video gave me keyless entry after owning the car for several years not having it.
7:49 PM, 6/21/2021 - just programmed a fob for my Protege5, with the help of this video. Thank you!
Thank u man! Works like a charm on my 2012 Mazda 2 and also starts working third button for trunk release that i've never had before! Thank you!
Im about to buy a 2012 Mazda 2. Thanks for verifying!
Thanks heaps! I did it on my 2005 Mazda 3 and it worked. I would only add that I first needed to start the car with the door closed, then turn off the engine, open the door and follow the rest. I also left the key in the ignition. Crazy but brilliant!
Just wanted to say a BIG THANK YOU! Your instructions worked perfectly, even though my Mazda is a right hand drive! I'd seen previous instructions about turning the light on and off three times - total twaddle.
I'd just replaced my battery and was very peed off that it wouldn't work. I watched your video once, and 'hey presto' - spot on. Thanks again, you've saved me £££'s. If anyone wants to know I have a 2002 Mazda Premacy Gxi 1.8 litre. Thank you sweetcheeks, I'm thrilled :-D
thank you so much, I just went to a Mazda dealer and they only take my money, because I buy the remote control in eBay and not with them, but now I did program my remote control by my self .
Thank you - followed your instructions and it worked spot on. I have noted that some other instructions say to remove the key from the ignition after turning the ignition on and off three times however this did not work for me. Leaving the key in the ignition as per your instructions worked. Thanks again and all the best - Cheers.
I used it on a PK 2011 Ford Ranger with a Key Fob in Australia. Meaning right hand drive. Worked perfectly first time. Thanks for posting the video.
That is correct. The "switchblade" key is only available for 2010 on the Mazda 3 model. The 2004 Mazda 3 has a separate key and remote as shown on our website; however, the programming procedure is the same for the remote whether it is separate or switchblade.
2008 Mazda 6, 2 years thinking the fob didn’t work for me. THIS PROGRAMMING WORKED FOR ME!!
It worked like a charm on my 2003 Mazda Protege5! Thank you very much. It was the second time I had to reprogram the remote key. The first time I went to a Mazda dealer and the key was reprogrammed at no charge, but it's much more convenient (and empowering!) to be able to do it myself! Thanks again.
Michel Bruyère did your Mazda keyless entry stopped working and you reprogrammed it? Or did you buy a new key and programmed that one? Please help!
A little tip if you have a key release button, you don't have to turn the key to the release position each time. Just turning the key from run to the acc position worked for me. I had some issues at first trying to turn it to the release position until I tried it without pushing the key release each time. Just thought I would share in case anyone else was having this problem.
OMG this is literally the only way that it went into the programming mode. THANK YOU
This worked. For my 2012 Mazda. Had 1 working Key and purchased 2 off-brand keys. Went through these steps and now they all lock/unlock the door. Now have to get the 2 keys cut. I am unclear whether there is a chip that also needs programming in order to start the ignition. Just one note. Be sure to do the working key. My first attempt I managed to program the 2 new keys and unprogram the original key. On the second attempt I pressed the unlock button on all 3 keys and that did the trick. Good luck.
+Michael Phillips Yes, there is also a chip in the key that will require separate programming by dealer or locksmith to be able to start the car with the keys. Happy to hear you got the remotes working. :)
+carandtruckremotes how much on average does it cost to get the other (to start ignition) portion programmed? And what am i asking them to do so that i wont get charged for the programming you just showed us. thanks
Wow it actually worked on my 2006 mazda 3. Took 3 tries but finally synced. Thanks
I have a mazda 3 2006 which has issues with the remote. Can you plz recommend me where i can buy a replacement remote from?
Worked great on my uk spec Mazda 3. Thanks for the info and an easy to follow video.
Thanks for this instructional video. Worked first time reprogramming my remote for a Mazda 323 ba Astina hardtop.
It works on my 2007 Mazda 3. Thank you! Just bought a used key fob from eBay and programmed it using this technique. Now I just need to get it cut and program the chip at the locksmiths :)
Hi, I'm really struggling with the same car as yours, please help
@@statudem8360Same. Mine won’t work on my 2007 Mazda 3.
Thank you! This worked like a charm. You saved me $288, per the dealer price to buy a new one and reprogram it. I have a 2008 Mazda 3.
I’m going to do this tonight. Also have a Mazda 3 and was nervous until I read your comment.
I followed everything he said to program my new additional key for my 2011 mazda 3. Worked perfect. Only problem was it cancelled out my original working key. So I redid the steps and reprogrammed both keys. very Easy. Thank you vey much!!!
I'm worried it will cancel my original key. Did you manage to get both your keys working?
Many thanks for this video, it was annoying me that I couldn't get my central locking to work after changing the battery in the fob but this video showed me where I was going wrong 👍
Thank you so much for making this video I almost payed 300$ to program my vehicle and your steps actually work.
Thank you very much sir for this lovely video . I got my new remote working just following the steps you showed in this video.
Thank you! This worked on my 2008 Mazda3.
Perfect! Worked like a charm for my 2008 Mazda 5. Thank you for posting your video.
@David Gorris Mine wasn't a new key/keyfob ... my old one just stopped working for the door locks. Once I replaced the battery I had to go through the procedure noted in the video to get the keyfob synched to the car again. It's been a LONG while since I needed a key/keyfob for a vehicle. Last one was for a Ford more than 10 years ago. I did have to get that done at the dealer and it cost about $75, but I'm sure prices have changed since then.
Thank you!!!!!!!!! I just programmed my remote by following your directions 😀
thanks a lot!! worked for my mazda5 and saved me 130 bucks !!
Yes, you simply have to push the button on each other remote before exiting the programming mode. You can have up to 4 working remotes.
I have a 2012 Mazda 2. I am being told on a Mazda forum that I can buy the remote from yourselves and a blank key from ebay, get the key cut by a locksmith and then program using this method and it will all work. But youve said below that I will need to get Mazda to program the key to start the engine. Little confused now
James Baldwin That is correct... there is a transponder chip in the key that must be programmed by a dealer or locksmith in order for the key to work to start the car and keep the ignition engaged. The remote can be programmed yourself at home with a working/programmed key.
Verry helpful. Thanks a lot for this video. Without it I would've not been able to pair the key with my car.
you have to be watching the video very closely after the 3 off-on cycles you leave the KEY in the ignition and then close the already opened door 3 more times. Then the computer will give you a 60 second window to press the unlock button of each fob ONCE, for a Maximum of 2 remotes. Do not press unlock twice on each remote!!! as that will overwrite the 2nd slot on your 1st fob.
Hi. I have a 2007 Mazda 6. When I got the car from a dealer it did not come with a remote control. I only have the key. How can I program a remote to work with my car?
I bought yesterday two new keyfob remote control. I will try programming them next week. Hope this steps will work.
quick tip. You saw that original stopped working. What happened is that he didn't also double tap it's 'unlock' button quickly after doing the 2nd fob. I did the same mistake too. I had to go back. get to that step and then SUPER QUICK, double tapped the 2nd fob, and then quickly double tapped the original in the ignition fob as well. Then presto! My original worked and so did the 2nd one. I realized it wasn't clear in the instruction video, and I read elsewhere and some people didn't stress that enough...
Thanks, worked for 2006 Mazda 3. However, my lock button was acting as my panic button and vice versa. Very frustrating but I finally figured out it isn't a programming issue. I had purchased replacement fobs from ebay and they installed the circuit board upside down. With a small flat head screw driver it's easy to pop open the fob and reverse the circuit board. now if I could only disable that damn panic button...
The same thing happened to me... Tried programming an eBay fob since the battery fell out of my old one, and set off the alarm. But it's not working now so maybe I'll try again
+roverspinne yes it's very easy to reverse the circuit board and I was even able to pry the panic button off the board (just the tiny white button at the top of the apparatus) so the red button is still there but no longer functions
Hi there i have 2009 Mazda 6 i made all the instruction that u mention i arrived until the door sign "lock unlock " and then i hit the remote botton 2 times and there is no action,,any help?
My car came with 2 keys and 1 remote. So can I buy a remote (have the current remote in the car) and follow these steps to have the new remote programmed?
I have a 2008 Mazda 3. When I got the car from the dealer, it didn't come with a remote, just a key. I called Mazda and gave them the vin number of my car and they said that my particular car doesn't come with the remote option. If I got an aftermarket remote, would it work? My car has power locks...
I just bought a 2008 mazdaspeed 3. I remembered I had a keyless remote of my 2006 mazda 3. I attempted to program it but it did not work. The vehicle responded just as your video, but the remote did not work as far as opening nor closing the doors. I tested the remote battery to see if it was bad. It gave me a reading of 3.18V.
My question to you is if it's a different FCC number between a 2006 & 2008 models. But apparently it's the same 2006 to 2009 mazda models or it's because a regular mazda 3 and a mazdaspeed 3.
Thanks for your video it was helpful since I got to do it more with your video than just the online instructions.
OMG! You saved me $225!!!!! Thank you!
Thanks so much for the vdeo. it was better than instructions that came with the remote.
is there a way to get the old remote working again after it died during the programming session?
After pressing the Unlock button Twice on the key he programmed, he was suppose to do the same, meaning also to press the Unlock button TWICE on the key that is on the ignition (while it is in the ignition). Otherwise the ignition key will be deprogrammed. If it happens to you, just repeat the same steps and press Unlock button twice on both keys, first on the new key you are programming, then on the old one in the ignition. My ignition key was deprogrammed as well, and I did the above.
Thanks for the tip. Wife was a bit confused why the original fob no longer works.
Where do you buy the spare key?
Thank you!!! I could not figure out why my keys kept deprogramming.
Hello. I have a Mazda 6 year 2006. Can you please guide me to get the correct fob that so I can program it. I only have the ignition key no fob. Thank you. JC
Thanks for the great video, I tried this and it works of course. I want to buy another remote that I can have a new key cut for and also do this programming process myself for the new FOB. However I have been told that I will need to actually have the key programmed itself by the dealership ? Is this true or do you have a video on how to program the key itself ? Thanks and look forward to hearing back
+Steve Pena Unfortunately, that is true... the key does have a chip in it. They key would have to be cut and programmed to start your car by a Mazda dealer or a Professional Automotive Locksmith. Of course, the remote part you can program just like the video here. Let me know if you have any further questions. :)
Steve Pena
You don't have to go to the dealer to hey the key programmed as long as you have the two Reginald keys that are already pre-programmed.
I found these instructions on a Mazda forum- link below. I bought an extra key as I wanted a flip key for my car. I bought the key online from a dealer for $100 and they even cut it for me. All I had to do is program it. This will save you a trip and money. But remember you need to pre-programmed key to do this programming. Otherwise you will need to go to the dealer.
www.mazda3forums.com/95-maintenance-care/205734-spare-key-self-programming-how-guide.html
Thanks a lot you save me time I do exactly what you are saying and my remotes work great 👍 Thanks a lot
Great video.. I just replaced my battery Worked first go...there's so many other videos on this but they don't work thanks again
This worked for me. Thank you for sharing.
Does this still work if you lost all the original key fobs when you try to program a new one? Or would i have to go to dealership?
Thank you, this procedure worked on my UK 2007 mazda RX-8..happy days
My 2013 Mazda 6 does the lock cycle after I open and close the door 3 times but it doesn’t do anything after that when I hit the lock or unlock button twice……I know this post is very old but any advice would be awesome…thank you
Just programed a second remote. Thank you very much!
Thank you Sir, great instructions and very helpful.
I am working on a 2008 Mazda 3. I am trying to program the remotes. I am at a repair shop that lost the remote key. when I do the same procedure you did in the video, after opening and closing the drivers 3x the locks do not cycle to indicate I am in programming mode. I can see the door light on the dash so i know it pick up the open/close signal. if I remove the key or close the door, the lock will cycle 2x to let me know I am exiting programming mode. have you ever seen this issue ?
Sir
How i can programming a new reomte but with out old remote.
Just i have normal key!
Thank you, just did it on a new remote and it worked right away, took about 2 minutes, thanks for the vid.
hi bro, is that the only remote for your car or you do have another one working just add a new one? as I did exactly the same way but nothing happened after press remote botton twice, I heard that there are two different remote for the rx8, which you do you use? thanks a lot~
Worked on 2013 Mazda5 Sport. Thank you so much! This saved me $140!
ptys007 What I found is that this just enables the remote to work. The key still needs to be programmed by the dealership or else it won't start the engine...
+ptys007 *** YES ***this is often over looked. The original remote has a transponder chip which controls the engine immobiliser feature which needs to be programmed by a Mazda dealership or professional locksmith.
2009 MX5 - it worked for me - thank you
Tried this on a 2008 Miata. The lock and unlock buttons work but the trunk release now acts as a panic button. Am I missing something with the programming steps?
Thanks. It worked with my Mazda 3 2005
Have a 2006 Mazda 6 and all of a sudden both fobs stopped working. Thought it was the battery so changed in both but still didn’t work. Used this method and it worked! Only problem is just like the video, I could only do one of the two fobs I had in the car. Tried a few times but could only do one and not the other. Is there a way around this?
So, let me get this straight. I have a 2007 mazdaspeed 3, but i dont have one of those flip key with the keyless entry attached; Mines are seperated exactly like the 2nd one you were holding. Following this video will get me going with a flip key with keyless entry attached; just like the one in the ignition? If so, i will buy me one right now!
they had a lot of these conversions on ebay
sam ly Unfortunately, the "flip key" or "switchblade" type keys have different FCC ID numbers, so they will not work on your vehicle. Although the programming does work for those types of remotes, the remotes are not interchangeable with your car's ignition.
We have an MX5 lhd, NC 3.5, 2011, we have two fobs neither seem to work, only manually opening drivers door, (but does not open passeneger door even with key,) and passenger door has no lock on outside. The indicators flash when buttons are depressed on fob but nothing happens with doors, and light on fobs are red so assume batteries are ok ! Really hope we do not need two new actuators ! Only had our new car 1 week.
Try rebooting the car by disconnecting the car's battery for about 15 mins. Then try the programming again. There may be something wrong with the remote or the remote system. Do you get the initial response from the car?
inserted NEW battery in my remote for '05 Mazda 6, then I did the procedures you showed. I can hear the clicking on door locks exactly as your video shows. But after all done correctly, my remote does not open nor close the door (seems dead). Do you think the remote is bad? Any opinion? thanks.
giuseppe3010 Yes, this is usually an indication that there is something going on with the remote. Check the battery and have the remote tested for free at a local auto parts store.
Do you know what the programming procedure is for a Celice gts 2001 model please ?
No, I am saying that, Unfortunately, the switchblade key WILL NOT work on a 2004. You can only use the separate key and remote on the 2004 Mazda 3.
Can you have two working remotes at once? I don't want to delete any programming on the original key I have... please and thank you, great vid!
Do you think you’d ever do another video that’s updated for a 2016 and later?
Not going to lie I thought I was getting trolled. Very surprised it worked!
Hello. I own a Mazda 3 2004 Hatchback. The key comes with a seperate remote control for lock/unlock. Can i use your remote switchblade key? I understand that i have to cut and program the key but if i do that and follow your instructions on the video for the remote part will it work? Thank you. Greetings from Greece!!!!
Does it need any extra features or parts installed in the car or I just need ta key to program it with my car?
If the car is responding initially, there may be something going on with the remote. If the car does not respond to the programming procedure before you get to the remote part you may need to "reboot" the car by disconnecting the car's battery for about 15 mins and then trying the programming again.
This seemed to odd to me, but to my suprise I was able to get it on the first try. Thanks !
2012 MAZDA 2 WORKED PERFECT THANK YOU SO MUCH
Im about to buy a 2012 Mazda 2. Thanks for verifying!
@@hagar6908 Good luck wish you the best !
Hi, I watched your video several times and followed your instructions for my 2006 Mazda 3 but the new fob will not work. Any suggestions?
Thanks a lot! I was able to program one of my mazda 3's key fob to work on my mazda 6. AMAZING
So now the new remote works but the original that DID work, no longer works? You still only have one remote working?
It’s timed and it auto erase other remotes. He didn’t do it fast enough but these remotes don’t look and are reusable
Hi there, after opening and closing the door 3 times, it doesn't lock and unlock.
I have a 2010 Mazda CX-9. I have the BOTTOM of the remote key (as the top with the actual key fell off - lost). I purchased a new key and had it programmed with the ignition. So the new key starts the car - but the remote lock/unlock won't work. I tried what you said in the video several times, an it's still not working. The original lock/unlock is still working - but I want the new key to work. Please advise!!!
+Kelly Adams you can try rebooting the keyless system by doing an electrical reset on the vehicle.To do this you would simply disconnect one of the car's battery cables for about 15-20 minutes, reconnect and then try the programming again. Sometimes this will solve any 'bugs' that may be keeping the remote from programming.
Also, be sure to check the battery in the new remote. It might just be a bad battery.
If neither of those works, take the remote to a local auto parts store and have them test the signal. They usually have remote testers there and will test if for you for free.
I have mazda verisa car , I have smart card key, is it possible I get another one? Where I find it and how I do that key to programs key?
Will this work to programme a 2nd hand key fob to my car?
Hallo i have a question about mazda 6 2006 transponder chip i have lost my key and i dont know how many bits is the original transponder frequency. Can you help me. Thank you.
im using mazda demio 1.5 2006 which one comes with card reader or you can use keyless when the remote is near.. unfortunately when I was washing pants in the washing machine i forgot my key . so it not working anymore i can only acess the door using the key but without remote it doesn't start so any ideias???
Help!!! I bought 2 key fobs bc my old fob died and broke in half (so I've nly been using manual key access for some time now)
I followed the steps for my 1st key fob and it works perfectly!
HOWEVER, I can't get the 2nd key fob to program. I don't know what to do now. I've tried the steps numerous times with no result.
I have only one key just changed the battery and there is a light on the key fob and it doesn’t work so I need to get another key?
How do you replace the shell on a already programmed Smart key on a Mazda CX-7 2007? And if I buy the other key remote (Keyless Entry Remote + key) will it replace my current ( Keyless Entry Smart Remote) programming?
Will the new key start the car? Or is it just to lock and un lock the vehicle?
Thanks for your video and it works for a new remote for my 2009 Mazda 5. However, it works for door only and does not start the engine. Do you know how to register the new remote so that I can start the vehicle as well?
The chip in the key must be programmed to start the car by a dealer or locksmith. The instructions will only program the remote portion of the key.
Hello from germany, i've a mazda 3bk from 2004. It's the same way to program ?
Hi, How can I program the remote to unlock all doors on first press please. The second press to let the family in is unreliable and irritating for the kids who are yanking on the handles when they hear the first click. Kind regards Tim