@@johnghatti5435 there are many ways to remove broken studs etc, it all down to training and skill, drilling out and heli-coil being a popular method in the aero industry.
Thats happened to me so many times I dont even bother with those taps, they always break off in there and are as hard as a drill bit so drilling that out after is near impossible. Best to just drill the bolt through and pull the bits out with a pick or re-tap the thread if its messed up.
left hand drill bit would drill the same circular hole in the other direction no? Also not stripped, as he wound it out on the perfectly function threads. Rounded out would be the term.
@@DigitalArtisan77 Correct, it would drill a circular hole spinning in the opposite direction. The process of the left hand bit biting into the material is normally sufficient to break the screw loose. If it doesn’t, gradually increase size until you either remove the screw or you have removed enough threads to run a tap through it.
@@anything6398 Yes they are, and yes they are. Anyone who has ever attempted to use them in a recessed or flush screw will tell you, they seldom ever actually work. If the screw is still under pressure or is corroded, the action of the “Easy out” attempting to wedge its way into the remaining material of the screw actually causes the body of the screw to expand very slightly. This in turn wedges the screw into place even more. Making it ever more difficult to remove.
@@DigitalArtisan77 you would need an multiple drill bits left handed. Easy outs are cheaper than buying every size in drill bit that's all I mean. Your way is good too.👍💯👍
I've worked on planes for 21 years, we've used these and the stubby 1/2" drive variant. These work fine 99% of the time. Choose the right drill size, keep tapping as you spin, works just fine.
@@jasonritter2492 I call bs these things suck 90% of the time iv been working on cars my hole life and these barely work right the square ones r better
I usually end up snapping the extractor in the bolt I've drilled out. But that's on M6 and smaller bolts usually with the smallest 2 extractors. Major pain
@@DigitalArtisan77 I will say the stubby MAC easy outs are some of the best I've used. They just don't go small enough for the bolts I tend to work with most of the time.
@@samhillyersh you are making a joke but I'm not. Normal drill bits are right handed and when used youbrotate the clockwise. That would tighten a bolt. A left hand drill needs to be spun the opposite direction and could loosen a bolt.
@@cbrunnem6102 does it actually though? Because in a hole thats not a blind hole, (accessible from both sides) I've yet to see a RH drill bit push the screw through the hole, so why would. LH bit pull it out?
These are the same thing as a Tap & Dye set with a "T" handle to turn them the "T" handle fits these extractor sets also if you need it put more plainly they even have ratchet "T" handles for the tap and die that fit the extractor taps
@@edwardvankirk3515 thanks for that but unfortunately when you put it plainly for me it confused me more. I just can’t seem to visualise a ratchet T handle on a die stock.
@@mike6932 amen to that, the best most effective way for me that is, mig a washer to the broken bolt then mig a nut to that the heat from the weld goes into the bolt too then it should Possably maybe come straight out no problem lol
I’ve got the same set of easy- outs. However, he used the crescent wrench BACKWARDS! It can sometimes work that way but it works much better when used properly.I was a mechanic for large manufacturing companies so I know of what I speak.
The problem is easy outs don't work 2/3 of the time they break off inside and then you have hardened steel to deal with as well I found that before I start twisting on the EZ out if I take a torch and heat up the area around the bolt that I'm trying to remove helps immensely the heat from the torch makes the metal around the bolt expand a couple thousands of an inch or so but it helped break the rust loose
To anyone that thinks this is foolproof I’m here to tell you it’s not, this will work on an already loose bolt or a bolt that hasn’t really been torqued down tight. I wanna see this with a bolt torqued to even say 20ft lbs and is seized tight from years of rust and corrosion. Even with heat you will be hard pressed to get it out
Tried this trick several times to absolutely zero success. That bolt face was rusty, but had definitely been removed before trying to use the Left handed drills etc as there was zero rust around the bolt.
Craftsmen tools are not the highest quality, but they make a way better extractor kit. The bits have a 13mm head, use a socket and ratchet or a 13mm wrench in a tight spot. They also make an external extractor set for bolts with stripped heads.
Just go a little deeper with the drill, until the hex head comes off. The exposed bolt shank isn't hard to get out after the gearbox flange is removed. A broken ezzee out is a huge pain.
я слыхал что есть способ, розсверлить убитый болт, и нарезать в нём левую резьбу, и вкрутить туда собственно болт с левой резьбой, до упора, и оно выкрутиться
Take a socket torx bit and hammer it in the rounded hole. Then use a ratchet to remove. Doesn't always work but way quicker and easier than this for a first step
drill the head out first, if the bolt hasn’t bottomed out it should only be tight on the shoulder then you can use an easy out or left hand drill bit. doesn’t always work but it’s a good starting point if welding a washer and nut doesn’t work
Having this issue right now and never used an extractor before. How deep does it need to be cause seems it keeps just eating away on it. Working in confined area of a washer. Using hand tools not power tools on extractor as suggested
How did you strip the bolt if it was that easy to twist off in the first place. I want to know how to remove a stripped bolt that even with a 2 foot long leverage, that bolt aint moving.
And don't get started on the broken drill edges 👌 it's really a gamble plus has high risk of losing either tool or the thing you wanted to open maybe even both.
The backward screw device is called an " Easy Out" has been around for decades. Trick is to use penetration oil on the broken bolt' s threads, let it soak over night. Never use a crescent wrench for anything...works loose and slips....no knuckles time ..
Damn. I'm having same problem with with 2 M8 Torx of the brake disk of my Trafic. Extractors don't work. Bolts are torqued tight and corroded. Nightmare.
Hammer the top of the built then retry Allen wrench....would do this as a machinest. It smushes the sides allowing you to be able to turn. If not an easy out
And when those don't work the part is either messed up or you take it to a machine shop. Get that kinda stuff come through our machine shop every once and a while had to extract 5 1/2" bolts from a $10,000 part. It's a bet nerve racking at first but you get use to it and now it's like clockwork.
There's just something about a mechanic using an adjustable wrench backwards that gets on my nerves.
Tf you mean backwards
The way he's using it is backwards. Spreads the jaws open
Plumbers use adjustable wrenches, a good mechanc/technician, does'nt butcher nuts and bolts or tools in general.
I’ve never had luck with that style extractor to begin with. The wrench being backwards doesn’t bother me that much though.
@@johnghatti5435 there are many ways to remove broken studs etc, it all down to training and skill, drilling out and heli-coil being a popular method in the aero industry.
That actually works about 1 in a thousand lol. Usually the head pops off and you end up drilling it completely out
Thats happened to me so many times I dont even bother with those taps, they always break off in there and are as hard as a drill bit so drilling that out after is near impossible. Best to just drill the bolt through and pull the bits out with a pick or re-tap the thread if its messed up.
Yes drill it out
No, it works about 700 out of a thousand. You just have to know what you're doing. Obviously, you don't.
This works "sometimes" Kinda need ideal conditions though. I've also ended up with a broken extractor. Drill the whole mess out and helicoil
If it isn’t recessed like this one and you can get around the head of the screw I’ll pull out the grinder.
How did you get the extractor out?
Not a broken bolt. A stripped screw, yes. Those things almost never work on truly broken and recessed/flush screws. Best bet is a left hand drill bit.
There called easy outs . They are left handed .
left hand drill bit would drill the same circular hole in the other direction no? Also not stripped, as he wound it out on the perfectly function threads. Rounded out would be the term.
@@DigitalArtisan77 Correct, it would drill a circular hole spinning in the opposite direction. The process of the left hand bit biting into the material is normally sufficient to break the screw loose. If it doesn’t, gradually increase size until you either remove the screw or you have removed enough threads to run a tap through it.
@@anything6398 Yes they are, and yes they are. Anyone who has ever attempted to use them in a recessed or flush screw will tell you, they seldom ever actually work. If the screw is still under pressure or is corroded, the action of the “Easy out” attempting to wedge its way into the remaining material of the screw actually causes the body of the screw to expand very slightly. This in turn wedges the screw into place even more. Making it ever more difficult to remove.
@@DigitalArtisan77 you would need an multiple drill bits left handed. Easy outs are cheaper than buying every size in drill bit that's all I mean. Your way is good too.👍💯👍
I've worked on planes for 21 years, we've used these and the stubby 1/2" drive variant. These work fine 99% of the time. Choose the right drill size, keep tapping as you spin, works just fine.
Thats crazy , im actually about to graduate college in December for Aerospace Engineering and dont know where to start , any advice/tips ??
True, a lot of people tend to hurry and overtorque, thus breaking the easy-out.
It's a simple system.
What is name of this wrench
This man needs a Nobel prize he's the first person to ever make that actually work. Lol
These actually work all the time
Square ones work much better
These work great.
In the engine building world we always get them to work right. You just got know how to use them..
@@jasonritter2492 I call bs these things suck 90% of the time iv been working on cars my hole life and these barely work right the square ones r better
I usually end up snapping the extractor in the bolt I've drilled out. But that's on M6 and smaller bolts usually with the smallest 2 extractors. Major pain
Buy snap-on or quality extractors. Impact hardened with impact driver even better, grind tip off extractor if too long and weak.
@@DigitalArtisan77 Lol I have both snap on and mac. Nice try tho
@@DigitalArtisan77 I will say the stubby MAC easy outs are some of the best I've used. They just don't go small enough for the bolts I tend to work with most of the time.
@@JDuBz815 any tips for a deep broken m6 in an aluminum motor casing? My 30 minutes job has just turned into a nightmare
@@davidorozco1888 what have you tried? Blind hole?
Step 1 drill a hole.
Step 2 use crescent wrench backwards.
Step 3 remove bolt.
Not to mention pounding on the easy out...eek
More often then you'd think, just using a left handed drill bit will work.
Theyre just so much easier to use than right handed ones
@@samhillyersh you are making a joke but I'm not. Normal drill bits are right handed and when used youbrotate the clockwise. That would tighten a bolt. A left hand drill needs to be spun the opposite direction and could loosen a bolt.
@@cbrunnem6102 does it actually though? Because in a hole thats not a blind hole, (accessible from both sides) I've yet to see a RH drill bit push the screw through the hole, so why would. LH bit pull it out?
@@machineman8388 a LH drill bit can end up grabbing it and rotating it out. especially if the head is left. it just works. don't it dozens of times.
Always use a tap wrench, with an easy out.
no se porque para todo usan la cresent
They need to start making round Allen keys for when this happens
Big brain
@@sleepysloth7885 small really because it will slip
Tô
Gente
How does one think of such lol
Use a tap wrench to turn the extractor. The leading cause of broken extractors and fasteners with even more damage is uneven loading of the extractor.
Good job, but it usually doesn't work that easy 🤨
@@michaelstippich3464 day
By
It would be amazing to get a bolt out that easy
Genius! Tap it out. Never would have thought of that!!
There's a Tap "T" handle that goes on the square at the top so you don't strip or crack the Tap
Where’s the tap ?
These are the same thing as a Tap & Dye set with a "T" handle to turn them the "T" handle fits these extractor sets also if you need it put more plainly they even have ratchet "T" handles for the tap and die that fit the extractor taps
@@edwardvankirk3515 thanks for that but unfortunately when you put it plainly for me it confused me more. I just can’t seem to visualise a ratchet T handle on a die stock.
Not worth the time to explain
Push your Google button search it and educate yourself
Такую тайну показали что просто слов нет😁😂
Wow is that how u do it? Iv been using the extractor upside down this whole time.
I use a torx bit and hammer it in and remove with a ratchet. works great
Awesome....do this with about 2" radius clearance deep inside an engine bay😂
Exact pal its clear everything easy
These removal tools are ok but they expand the bolt sometimes making even more stuck
I agree. They don't always work.
Nahhhh your negative
@@grincadorna4753 no mate I have over 25 years experience and use these tools on a daily basis
That's why they invented helicoil 😆
@@mike6932 amen to that, the best most effective way for me that is, mig a washer to the broken bolt then mig a nut to that the heat from the weld goes into the bolt too then it should Possably maybe come straight out no problem lol
My favorite part is when you snap the easy out off in there as well.....nothing better than that feeling
Really makes your day
@@ferrumignis snapping an easy out off in a bolt 🤤🤤🤤 ughhh gets me so moist 😍
😂😂😂😂
I’ve got the same set of easy- outs. However, he used the crescent wrench BACKWARDS! It can sometimes work that way but it works much better when used properly.I was a mechanic for large manufacturing companies so I know of what I speak.
Torpe para comer unas llaves y k bueno cuando le interesa
Please tel me the name of this tool.
@@joseangelfloresgonzalez5682
.
use them all the time successfully... in australia we call these tools “easy outs”
Here in Merica we call them that also
Um, left hand drill bits works great too. Since the threads go to right. Unless its left hand threads. You use regular drill bit (AKA right hand).
I’ve tried that kit so many times and never got a screw that was seized out. It might work if screw is slightly tight that’s about it.
Agreed. Getting any rusty stripped bolt out is like winning the lottery
I have had some success, little, but on this I would try heat?
Heat helps quite a bit. Using the biggest extractor possible helps. But I've snapped more extractors than I have successfully gotten the bolts out lol
Dari Awal sampai Akhir Video nya sangat Menarik..
Di tggu Video Lainnya..
Гайку сверху приварил на 2-3 прихватки и выкрутил... не усложняй сущности, без надобности...
Links to the tools would be great
2 in 5 chance the EZ out snaps.
Yep. Only a moron would leave the head on while using the eazi-out.
Been there, done that. Sometimes with a 1 inch Allen bolt, at the bottom of a 6 I ch deep hole. Sucks, big time...
@@larrystuder8543 everyone watching this was waiting for the *snap".
The problem is easy outs don't work 2/3 of the time they break off inside and then you have hardened steel to deal with as well I found that before I start twisting on the EZ out if I take a torch and heat up the area around the bolt that I'm trying to remove helps immensely the heat from the torch makes the metal around the bolt expand a couple thousands of an inch or so but it helped break the rust loose
Je nadmet pas la langue anglaise
They've been called easy outs for years
To anyone that thinks this is foolproof I’m here to tell you it’s not, this will work on an already loose bolt or a bolt that hasn’t really been torqued down tight. I wanna see this with a bolt torqued to even say 20ft lbs and is seized tight from years of rust and corrosion. Even with heat you will be hard pressed to get it out
Or just use a Dremel to cut a slot into it and then unscrew it with a flathead screwdriver.
Tru dat
Yea that's the thing you do before piercing it
Tried this trick several times to absolutely zero success. That bolt face was rusty, but had definitely been removed before trying to use the Left handed drills etc as there was zero rust around the bolt.
Allen keys are meant to work perpendicular to the fastener going at it at a 45 degree angle doesn't work
I've broken a couple of these and never got them to work. Rose-weld a nut on top is better, as the heat also works in your favour.
You used with a tap wrench with even pressure / force towards the threads? Sometimes while lightly tapping?
It should work 90% of the time.
Там болт в масле , и так бы открутился . Вот с блока цилиндров закисшую шпильку бы он так выкрутил ,это другое дело
I knew that 30 years ago. Thanks for reminding me.
On internet every basic task can be interpreted as a professional lesson.
Take some copper wire, bend it into a U shape and put it into the stripped opening. Then add your bit/tool. Works 60% of the time.
60% of the time….works every time - Ron Burgundy, master carpenter
I must try this
@@johanneshofstetter3949 հ
00 UB
Craftsmen tools are not the highest quality, but they make a way better extractor kit. The bits have a 13mm head, use a socket and ratchet or a 13mm wrench in a tight spot. They also make an external extractor set for bolts with stripped heads.
Если бы он был нормально закрученный, шляпку болта обрезала бы и прошлось бы высверливать болт и нарезать резьбу.
Just go a little deeper with the drill, until the hex head comes off. The exposed bolt shank isn't hard to get out after the gearbox flange is removed. A broken ezzee out is a huge pain.
If you didn't round out the bolt then you wouldn't have to do this
Better off welding it up then twisting it off before snapping the easy outs lol especially on anything aluminum the welding trick is amazing
Уоаопвра☺😀😆😆😉😆
Try doing that under the hood of a 95 Ford probe. 🤣😭
最初の段階で六角レンチいけたのでは?と思ったのおれだけ?電動だと、あの古さの六角ネジだと手動でやるのがベストかなと。古くてサビたネジはネジ山だめになるから、電動だとすぐネジ山ダメになるし。
これはいざとなったらしかかな
я слыхал что есть способ, розсверлить убитый болт, и нарезать в нём левую резьбу, и вкрутить туда собственно болт с левой резьбой, до упора, и оно выкрутиться
Не у всех есть болты и метчики с левой резьбой одинакового шага - они не маст хэв
Авсверлить проще
Доктор Дью уже выехал за ними))
Так как он крутит, ему для каждого болта эта елда понадобится)
А еще можно просто приварить другой болт, главная проблема это доступность
Take a socket torx bit and hammer it in the rounded hole. Then use a ratchet to remove. Doesn't always work but way quicker and easier than this for a first step
Судя по остальным засверленным шляпа полная , это была самая удачная попытка.
говорят, что конкретно эти экстракторы полная хуйня
другой формы и другого вида экстракторы в виде пики крестообразной еще может быть... но не это фуфлостракторы
@@dimasamsonau3646
Catastro Get la
Y
Venta
As a machinist I would like to say, Easy Outs work! Haphazard at best but they do work! Sort of! Lmao 😂
Judging by the all /16 he used on the extractor he’s probably the one that tried to pull a 6mm alan head bolt with a 5.5mm key 🤣
Ychttb ha mmmmvxxxxx
Colocando a ferramenta torta daquele jeito não tira nenhum parafuso mesmo 🤣😉
Для тех кто не умеет пользоваться ключами.
drill the head out first, if the bolt hasn’t bottomed out it should only be tight on the shoulder then you can use an easy out or left hand drill bit. doesn’t always work but it’s a good starting point if welding a washer and nut doesn’t work
Экстрактор помогает разве что 2 раза из 10 случаев.
А точнее в тех где болт насмерть не прикипел. Иначе есть шанс обломить экстрактор.
@@penguinkowalski3660 ну дык сначала вдшка, потом экстрактор
Болт был откручен зарание-видно!
Left handed drill bit in a drill press slow speed with a little PB blaster on it and back it right out .
Yeah until the tap breaks inside the hole you got to drill out the tap.
Been there done that more times than I can remember A broken easy out is no fun
A tap is for threading....... he is using a stud remover, two completely different tools my friend
@@jaybee7291 yes I understand that, I guess you never had an extractor break.
@@jaybee7291 not a stud remover either, it’s called an easy out or broken bolt extractor. Definitely not a stud remover.
Or weld a wrench onto the bold and you can then easily unscrew it
Ходит легенда, что экстракторы именно так и работают 🤣
Ты хоть что-нибудь в жизни открутил экстрактором? У меня не хрена не получилось🤣🤣🤣🤣
@@user-bm5xl3db1w так в том то и суть что нет)))
@@user-pf6xu7vl3g нас жестоко на&Бали🤣🤣🤣🤣🤣
Having this issue right now and never used an extractor before. How deep does it need to be cause seems it keeps just eating away on it. Working in confined area of a washer. Using hand tools not power tools on extractor as suggested
Ну вот кто станет этим заниматься? Да ещё и деньги тратить на приблуды, сварка же есть у каждого
Сварка бесплатная?))
@@user-cz4ir1xq1s дешевле выйдет чем куча этих экстрактором и дрель покупать
@@user-cz4ir1xq1s ну это комент к видео, на сам деле молотка достаточно
@@sergeiangolenko7936 моя свареа например стоит сотку, экстрактор и дрель 5))
@@user-cz4ir1xq1s так она(сварка) у тебя уже есть, а то ещё в магаз сбегать прикупить надо
HOW TO TAKE BROKEN DRILL BIT 1.5mm DIA FROM AN ALUMINIUM CASTING?
You're even using the wrench the wrong way
In orthopedics we use same technique in blocked screws of bones
Wow. Could've saved yourself a shit load of hassle by just inserting the allen key properly in the first place 🤷♂️
How did you strip the bolt if it was that easy to twist off in the first place. I want to know how to remove a stripped bolt that even with a 2 foot long leverage, that bolt aint moving.
Явно руки не оттуда, о как он шестигранник вставляет
Доктора, позовите Доктора!!!
@@iiiiiiiiiiiiiiiiiiiiiiiiiii920 здраааааасть
And don't get started on the broken drill edges 👌 it's really a gamble plus has high risk of losing either tool or the thing you wanted to open maybe even both.
溶接が最強って、答え出たよな
The bolt holding the brakes to the fro t fork of my bike is like this, I'm glad I found this video
Where is the removing of a broken bolt?
If you use a tap socket for the extractor it really saves your knuckles when attempting to remove bolt.
아주 유용한영상 굿
Best feeling ever when that bolt turns .... omg
Right ?!?! Cmon !!
someone teach him how to use the basic tools first 😂😂😂😂
You use an adjustable wrench backwards. It should go the other way
Can you make an updated version for how to do this in 2022 now?
I don't think I have ever seen an extractor work in real life
おーお見事!まさかドリルの大きさで六角のネジ山潰れたの取るとは。日本とちがうけど参考になった!
ドリル?逆タップではないでしょうか?
Como se llama esa herramienta com dientes rosca para desatornillar.
Why not trying anti-rust solution before destructively removing. Rustolene etc
Don’t turn the wrench backward !
Ни разу у меня такой экстрактор не сработал, чаще всего они обламываются.
У меня тоже обломались, а обломок ни высверлить ни выбить, была жопа до екстрактора, после него стала полная жопа!)
Used to have a set like that, don't remember where's now. 😁
Usually stripped out,heat beat
The backward screw device is called an " Easy Out" has been around for decades. Trick is to use penetration oil on the broken bolt' s threads, let it soak over night. Never use a crescent wrench for anything...works loose and slips....no knuckles time ..
Seeing as this is what you are supposed to use that is probably why it works.
Damn. I'm having same problem with with 2 M8 Torx of the brake disk of my Trafic. Extractors don't work. Bolts are torqued tight and corroded. Nightmare.
This saved my life so many times
Before you strip the screw, they make a tool that’s an Allen wrench, but you hit it with a hammer works almost every time
Hammer the top of the built then retry Allen wrench....would do this as a machinest. It smushes the sides allowing you to be able to turn. If not an easy out
Whats the novelty? Been doing that since the 3rd grade. Pretty "See Spot Run" dont you think?
I have never had any luck with that type of extractor.
I always saved my ex boss money by keeping a set of quality back out tools w me, the cheap ones break too easy
This is nothing new I was using this method 30yrs ago
@@andrewkaraiskou4790 you are old lol I’m not that old
There's screw extractors an tap extractors..there's all kinds tools for metal work..wish I knew them all.stager tooth dies an taps..I could go on
Works about 2% of the time living in Maine.
How come if screw in small diameter hole...i mean in damage screw far from surfaces
And when those don't work the part is either messed up or you take it to a machine shop. Get that kinda stuff come through our machine shop every once and a while had to extract 5 1/2" bolts from a $10,000 part. It's a bet nerve racking at first but you get use to it and now it's like clockwork.
Explicame como agujereas un perno de acero Alen ?
Para pernos de hierro dulce, puede ser, pero cementados...mmm...?
Curioso, es capaz de poner vertical una broca pero no una llave allen