How to Replace Front Brake Caliper 2006-12 Ford Fusion
HTML-код
- Опубликовано: 8 фев 2025
- Buy Now!
New Brake Caliper from 1AAuto.com trq.video/ia-1...
A worn out or seized brake caliper can create dangerous and expensive problems: overheating, rotor and pad wear, or even total failure. TRQ brake calipers are engineered to fit your specific vehicle. This video shows you how to a front brake caliper on your 2006-12 Ford Fusion.
• Check here for more videos on the 2006-2012 Ford Fusion: • Ford Fusion 2006-2012 ...
This repair was done on a 2011 Ford Fusion SEL 3.0L Sedan 4-Door AWD and the process should be similar on the following vehicles:
2006 Ford Fusion
2007 Ford Fusion
2008 Ford Fusion
2009 Ford Fusion
2010 Ford Fusion
2011 Ford Fusion
2012 Ford Fusion
Tools you will need:
• Hose Clamp Pliers trq.video/obU-...
• Brake Grease
• Liquid Thread Locker
• Drain Pan
Subscribe: / @trq
Check out our playlist:
Ford Fusion 2006-2012 1st Generation: • Ford Fusion 2006-2012 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. 
Авто/Мото
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
It would be nice if you told what size the bolts are before you remove them, but nice video. Thanks for sharing.
nice job but you rounding off that bolt 5 minutes in was a real kick in the nuts
Awesome walkthrough! Thanks for all your help.
This video is well done. You covered all of the details. Excellent job. Thank you.
Perfect step by step just done it, thanks bud.
Question when lubricating -- why did you not lubricate the Tins ? -- Fantastic Video Many Thanks
This is a wonderfully made video
Blessings
Great vid!
Best instructional video ever. Thank you. I can't wait to see your other vids. Liked and Subbed.
+Jim Bergen Thanks for the feedback! 1aau.to/m/Shop-TRQ
With the door panel removal you don’t mention the torx size or the bolt sizes and what is best bolt and nut to replace the rivets with.
+David Jones Thanks for the feedback! 1aau.to/m/Shop-TRQ
Saludos 🤗 desde Colombia 👍 😉 😊
My fusion had a recall on brake system and they say refill with dot 4
Which caliper pin is has the rubber gasket? I took them out and am unsure which one has the gasket.
A C-clamp squeezing the bottom pad of the pads together helps a lot before you put the wire springs on. Makes it way easier to slip the caliper over top of everything. 😃👌🏻
+@skeletor7908 Thanks for the feedback! 1aau.to/m/Shop-TRQ
My problem is the leake u have .. never good at that .. and wiper blades always buy an extra I get frustrated then chuck it
Put a hose and collection bottle on the bleeder. No need to make a mess.
U use to make gud videos bro...what's the lug nut size..the short 20 metric stripping the lug nuts an the 19 mm long not even fitting
The brake fluid used in this video is incorrect. Most Fusions require D.O.T. 4 brake fluid
No, these fusions are dot 3.
2010 Ford Fusion uses DOT3 (pg 321 of 2010 Fusion owner's manual)