How to Replace Front Lower Ball Joints 2003-2007 Honda Accord

Buy Now!
New Ball Joint from 1AAuto.com 1aau.to/ia/1ASB...
This video shows you how to install new, quality TRQ ball joints on your 2003-2007 Honda Accord. Car and truck suspensions combine a number of moving parts for safe and stable handling. The ball joint is the crucial moving component that ties those parts together. The ball-in-socket joint can wear out and loosen over time. Or, the rubber protective boot can tear, allowing contaminants to seize the joint. Bad ball joints are a common failure point on vehicle inspections because they lead to unsafe driving conditions. Fortunately, they are relatively easy to replace with the right know-how.
This process should be similar on the following vehicles:
2003 Honda Accord
2004 Honda Accord
2005 Honda Accord
2006 Honda Accord
2007 Honda Accord
Tools you will need:
• Flat Blade Screwdriver 1aau.to/obst/1A...
• 10mm Socket 1aau.to/obmo/1A...
• 17mm Socket 1aau.to/obGQ/1A...
• 19mm Socket 1aau.to/oaoY/1A...
• 32mm Socket 1aau.to/odh/1AA...
• Ball Joint Press
• Brake Caliper Hanger 1aau.to/ojV/1AX...
• Pickle Fork
• Snap Ring Pliers
• Wire Cutters
• Ratchet 1aau.to/obKa/1A...
• Ratcheting Bit Driver
• Socket Extensions 1aau.to/obGQ/1A...
• Swivel
• Torque Wrench 1aau.to/oaPu/1A...
• Copper Anti-Seize
• Gloves 1aau.to/oaqU/1A...
• Rust Penetrant
• Safety Glasses
• sanding disc
• Sandpaper
• Center Punch 1aau.to/oms/1AX...
• Floor Jack 1aau.to/oadA/1A...
• Hammer
• Jack Stands 1aau.to/oZ9/1AX...
• Large C-Clamp
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money

[@user-wb9wk3gw7q]

Great video! You left out the part where he puts the retaining ring back into the knuckle.

[@dknight211]

While replacing one of the front lower ball joints on my 2007 Honda Accord, I used a ball joint separator instead of a pickle fork. As I tightened down the ball joint separator with a hand ratchet, it shot out to the side (with all that built up energy from being tightened down) and hit my gloved thumb and almost broke it. I can see now a pickle fork is much safer!

[@jonathanbarros9948]

great video and very well explained, going to help a lot with mine tomorrow

[@Waldo1982]

Axel lug on a 4 cylinder is 32mm and 36mm on the v6 I believe

[@rubensolares9929]

Exelente muy didáctico lo mejor es la inclusión de los torques gracias por compartir.

[@rubencarorubio4992]

Good job bro, i love Honda

[@user-gp3fl6cs6y]

At what point did you replace the bearing? That’s brand new

[@christophergrandison5365]

Great vedio, but I never saw when you install the hub.

[@richardspaulding5035]

Why did you not show reinstalling the retaining ring????

[@josefranciscoesquertalaman3827]

Presente en las aventuras de mecánica automotriz TRQ, cordial saludo desde Navojoa Sonora México 🎉

[@marshallpomeroy224]

Any recommendations for getting the axle back in place with grease fittings on the ball joint? The ball joints I purchased came with grease fittings

[@elmerorellana9061]

Muchas gracias e aprendido mucho con tus videos y también e ahorrado $$$$

[@LuisMartinez-pd1bl]

You left A1 Auto ??

[@danp7463]

That lower ball joint look like it's the wrong size. There's a few options on ball joints when it comes to Hondas.

[@SashaNem]

thanks

[@mariarivas6377]

Thanks.

[@TRQ]

+@mariarivas6377 Thanks for watching our video! 1aau.to/m/Shop-TRQ

[@atlflores9623]

Anyone know where I could get a tin cap that goes behind the wheel bearings ? 8:00 is what I’m referring to

[@bluray4687]

You never showed the reinstallation of the tin

[@TRQ]

+@bluray4687 Thanks for the tip! We'll pass this info along to our production team. 1aau.to/m/Shop-TRQ

[@keijogronfors925]

Thats not so clean when you open that and it isnt so easy to put the paljoin out

[@christophergrandison5365]

Great vedio, but I never saw when you install the hub.

[@christophergrandison5365]

Great vedio, but I never saw when you install the hub.

[@christophergrandison5365]

Great vedio, but I never saw when you install the hub.