I can relate to pedalboard woes ... I've literally put a board together and was ONE CABLE SHORT of finishing it, and when I finally got the cable, I realized I needed to move stuff around again because I was just struggling to step on the right switches lol.
Dude. If you’re not going to go for custom cabling, EBS cables are your friend. Also, downvote for not using the Temple plates and then blaming that on the board. If you don’t want to stick their plates to your pedals, Board Mods has 3D printed plates that attach using the existing pedal screws. Adding bigger feet under the board will help with fitting power supplies - I run a Zuma underneath with no issues. Hope this helps!
EBS would've been a solid move, and if I did re-buy non-custom cables they'd be the way to go. I hope this video didn't come across as being anti-templeboard. I love the concept a lot, and I've bought another replacement one for the rebuild. A properly-done pedalboard with the temple plates, custom cabling, and CIOKS power is the dream - such a clean look. Just half-assing the commitment to the system like I have means that I'd probably be happier with a pedaltrain, buuut I'm sticking with Temple since I have the 4X mod and IEC mod. I really appreciate your comment - I'll look into Board Mods for sure. Adding bigger feet and more of the cross-supports might be a good way to go, do you have any recommendations for the feet? Thank you!
No worries! Temple boards aren’t perfect (ex: the module bay screws are terrible), and it is expensive to go all in for sure, but the final setup is light years better than traditional boards so I think it’s worth it. Like you, I committed for the 4 cable module. I forget the exact manufacturer, but I found “medium extra tall” rubber feet with metal washers in them on Amazon pretty easily. I also swapped out the foot and handle screws with more robust hex screws. BoardMods are great, though the posts do tend to break off pretty easily, and Sean also offers risers - I used one to place a pedal over the Zuma, attached with Temple plates underneath, without losing any real estate on top of the board. I don’t work for either company, just have a lot of experience building boards with their products!
![Natanael Cano - Amor Eterno [Official Video]](http://i.ytimg.com/vi/EO4prCs6WpM/mqdefault.jpg)
Velcro! Tisk tisk...Dual Lock is where it's at. 😎
Velcro is great when used properly, dual lock is the way if you’re not changing the board around too often though
This build was pure chaos and I'm here for it 😂😂 that siclone did some things, real synthy things and kudos to the new addition with the small stone 👍
As soon as the Velcro went on I knew this board was doomed, and it just fell apart from there 😂
@@KaiDown some times you just gotta embrace it 🤣🤣
I have finally achieved pedalboard nirvana. Volume pedal with direct out to tuner. Auuuuummmmmm.
I can relate to pedalboard woes ... I've literally put a board together and was ONE CABLE SHORT of finishing it, and when I finally got the cable, I realized I needed to move stuff around again because I was just struggling to step on the right switches lol.
Oh man, brutal 😄
Dude. If you’re not going to go for custom cabling, EBS cables are your friend. Also, downvote for not using the Temple plates and then blaming that on the board. If you don’t want to stick their plates to your pedals, Board Mods has 3D printed plates that attach using the existing pedal screws. Adding bigger feet under the board will help with fitting power supplies - I run a Zuma underneath with no issues. Hope this helps!
EBS would've been a solid move, and if I did re-buy non-custom cables they'd be the way to go. I hope this video didn't come across as being anti-templeboard. I love the concept a lot, and I've bought another replacement one for the rebuild. A properly-done pedalboard with the temple plates, custom cabling, and CIOKS power is the dream - such a clean look. Just half-assing the commitment to the system like I have means that I'd probably be happier with a pedaltrain, buuut I'm sticking with Temple since I have the 4X mod and IEC mod.
I really appreciate your comment - I'll look into Board Mods for sure. Adding bigger feet and more of the cross-supports might be a good way to go, do you have any recommendations for the feet?
Thank you!
No worries! Temple boards aren’t perfect (ex: the module bay screws are terrible), and it is expensive to go all in for sure, but the final setup is light years better than traditional boards so I think it’s worth it. Like you, I committed for the 4 cable module. I forget the exact manufacturer, but I found “medium extra tall” rubber feet with metal washers in them on Amazon pretty easily. I also swapped out the foot and handle screws with more robust hex screws. BoardMods are great, though the posts do tend to break off pretty easily, and Sean also offers risers - I used one to place a pedal over the Zuma, attached with Temple plates underneath, without losing any real estate on top of the board. I don’t work for either company, just have a lot of experience building boards with their products!
This might be the only cool looking PRS I've ever seen. But boy is it cool. Great tones too, very doomy
I appreciate that a lot! I'm totally obsessed with this PRS, it's been my #1 since I got it
You just kept me from purchasing a temple board, good looking out! 😎😅
Oh man 😄 I do love the look of a Templeboard when they’re done up properly with the plates, but it’s not something you can half commit to
Temple Boards are great, when you set them up correctly.