I think you've found the right balance with your editing, information and entertainment. This was one of my favourite of yours to watch so far. Fantastic! Looking forward to the next one. 💯
This looks great! I love that it has two different lifts. My best tip for lining up the tops (if double-sided tape or painter's tape and CA glue don't work as people have previously mentioned) is to use a piece of paper. Line it up exactly where the top will be, use a pencil to mark the holes, then flip that over to the bottom side of the box top and line up the corner of the paper with the corner of the top. I've used this trick a few times, both using the pencil to do a rubbing to get the locations of the holes, or just poke a hole in the paper where the holes are. My dad used to use graphite powder also to cover the bracket and put the top down transferring the graphite to the bottom of the board. The only problem with that is if you don't get the board set down exactly in the right spot or the bracket is just a hair too low, it won't transfer, but I've used that trick to and in the right cases, it works perfectly!
I would use a transfer screw set, or something similar to mark the holes for the lift mechanism. You could make your own by cutting down some screws, or sharpening some short bolts to a point. Look up transfer screws for the general idea of how they work, and with some creativity you could use the same principal here.
A trick to line up a top with the brackets in a situation like this is to use some 3M command strips. Line it up, press it in place, and if you use enough strips, you can lift the top up with the brackets attached. Adjust the hole position very slightly to account for the height of the command strip. Depending on the lift mechanism, it is sometimes easier to remove the gas assist.
I used blue painters tape on the table top and on the lift hardware with super glue between them. I then marked all the holes with a pencil, then removed the top and pre drilled on the marks. I put the table top back on the lift hardware and secured it with screws.
Great build! I thought of a trick for mount for the folding hardware. Start by supporting the mounting plates with two scraps so that it is level with the top surface, then use two sided tape to temporarily lay on the top. Afterwards fold out the top to drill the holes and mount the screws.
The finger holds is a nice touch, nice job on the build! Definitely can be built without expensive tools. Keep up the great work as the goal is for us to continue to inspire others to build something awesome! 👍🏼
Thank you so much for this beautiful design. My girlfriend and I both work from home and our new coffee table is perfect for us! I used double sided tape on the top of the hinges (Alien tape) and it was just strong enough to lift the table tops and then it was easy to drill the holes, remove the tape and screw the top.The result was perfect on the first try and it didn’t remove any of the finish. I’m not promoting this particular tape at all I’m just happy I finally found a use for it! Thanks again for your video and plans you are a great teacher and very talented!
I was just telling someone the other day that I wanted to build a table exactly like this, but had no idea where to start. Then this video showed up today in my feed. Excellent job. I'm no subscribed and will watch some of your other videos. Thanks.
I use paint sometimes to transfer marks. Cover the bracket in paint around the holes and carefully set the top in place. Flip it over and mark the holes with an awl, then wipe off the paint before it has a chance to soak in
Really do love this design - perfect setup for a sofa like yours! The mid video add was actually a Disney + ad...they must have watched the beginning haha
To mark the hole exactly to align the brackets to the table top squeeze a piece of cotton ball in to the holes and drop some ink on it. Lay the table top on top and there you have the perfect mark on your table top.
Maybe this was mentioned, I didn't read ALL the comments. I think you could save some alignment headaches with the lift-top mechanisms by changing the order of assembly a little. Leave the bottom out of the table until you have the top secured in place. This way you could just flip the table over and work on it from underneath.
As always, another great video! For the top installation, i would first install it like how you did, mark its actual size, then take it out to carefully trim to size. After that you already have the correct screw holes to reinstall.
Another great video and project, Alex! I love the double lift and I know you mentioned wanting better selection for the walnut, but I really like how the top turned out!
@@rajathygerlynhenry8931 I have not unfortunately. My friends shop got flooded at the end of the summer and he’s been rebuilding and getting things back in order. Once everything is up and running, I will definitely be!
Great build as always. Looking forward to the next one maybe with more angles, hehe. The queue of stuff I want to build gets longer every time I watch your videos. Your shop looking good too.
What's the trick for getting a good finish in the areas where you have glue squeezeout? Doesn't the glue fill the pores of the wood and prevent stain/poly from looking right in those areas?
Great build! I had the same problem lining the hinge mechanism and ended up referencing the holes like you have. Initially I used sharpened bolts through the holes to press the top down to get the position for the holes. Unfortunately I didn’t have the right size nuts so I had to use tape to hold the bolts in place which didn’t work real well.
I love this table , was wondering if hot glue on the brackets would be a good idea to have a temporary fix while you drill the holes, you have enough play at the beginning to use spacers and placing it , and at the end hot is easy to take off (only prob you might have some light sanding to do underneath but you would get perfect holes I think, just an idea , thank you for the plans !!
Great video and build Alex! I wonder if you could have done a clamped up dry fit without the bottom in place and then with the carcass upside down drilled the holes for the lift hardware?
8:00 Solution: Carpet Tape. Bourbonmoth I think his show is called does this. Used this for something else and it worked. But maybe someone already said this. 😂
I’m new to woodworking and have only built “shop grade” furniture in the past. I would like to start sourcing materials for this project but I’m having trouble procuring the 1/8” x 3/4” x 50” walnut edge banding. Where could I find walnut in 50” lengths?
Hi, the “edge banding” I used was just walnut lumber I cut to 1/8” thick strips. You can get lumber from woodworking stores like Rockler or Woodcraft, or other lumberyards. You can join Facebook groups and ask people who live in your area for recommendations
Maybe I’ll try it next time. These things are kind of like soft close drawers that take some force to pull open. But the tops are much heavier than drawer fronts, so it’s got gravity and weight working against it too haha. But CA glue might be the answer! Thanks!
@@BevelishCreations yeah for sure. Not simple.... I've never worked with this type of hinge before. But is it possible to adjust the tension on them temporarily? So its easier to open? Then once it's assembled you can tighten it back up?
Design the build of the table where the bottom panel can be left out. Then you can flip it over, lay it on the top and affix the mechanism through the bottom.
Very well done on video. I would add more time to the reveal. It is the payoff and everyone, not just yours, just breezes by the final. Make the ending more like Return of the KIng.
Great build! I have this exact same issue and I have been thinking about building a table like this. If I did not want the cubbyhole but just the whole long top to lift up, would it work the same or do I need a different lift mechanism?
@@BevelishCreations I’m not knocking you for having nice tools. More power to you. Obviously, I wish I had those. You just make yourself look like a fool, if you call them “cheap” or “basic”.
No I get it. I was just talking about the dowel jig. Because I usually build with the Domino before this. It’s been over a year since I built this, and I use this cheap dowel jig more than the domino
Please forgive my ignorance, still kind of a newb ;) ... at about 3:10 you're cutting the grooves for the pieces to lay in. Using a "dados?" ... is that just a router that you're suing a special name for... or is the dados thing the straight line you're using to make sure you don't mess up the straight line. This looks like a build that's just challenging enough for me, and I have a sheet or two of better quality plywood in the garage that just might make this something I can take on this summer... just want to make sure I have my ducks in a row first ;)
I think you've found the right balance with your editing, information and entertainment.
This was one of my favourite of yours to watch so far. Fantastic! Looking forward to the next one. 💯
Such an incredible build!
Thanks guys!
This looks great! I love that it has two different lifts. My best tip for lining up the tops (if double-sided tape or painter's tape and CA glue don't work as people have previously mentioned) is to use a piece of paper. Line it up exactly where the top will be, use a pencil to mark the holes, then flip that over to the bottom side of the box top and line up the corner of the paper with the corner of the top. I've used this trick a few times, both using the pencil to do a rubbing to get the locations of the holes, or just poke a hole in the paper where the holes are. My dad used to use graphite powder also to cover the bracket and put the top down transferring the graphite to the bottom of the board. The only problem with that is if you don't get the board set down exactly in the right spot or the bracket is just a hair too low, it won't transfer, but I've used that trick to and in the right cases, it works perfectly!
I might try that graphite powder idea!
I would use a transfer screw set, or something similar to mark the holes for the lift mechanism. You could make your own by cutting down some screws, or sharpening some short bolts to a point. Look up transfer screws for the general idea of how they work, and with some creativity you could use the same principal here.
Ohh that’s a good idea
Agree with the block plane. Keeps sharp lines and offers plenty of control. Thanks for sharing.
VERY cool to include free plans!
A trick to line up a top with the brackets in a situation like this is to use some 3M command strips. Line it up, press it in place, and if you use enough strips, you can lift the top up with the brackets attached. Adjust the hole position very slightly to account for the height of the command strip. Depending on the lift mechanism, it is sometimes easier to remove the gas assist.
Great design and really: Thanks to Rockler for sponsoring this.
Metric version would be great too :)
Yeah I understand. I actually build with metric
+1 to Metric
I used blue painters tape on the table top and on the lift hardware with super glue between them. I then marked all the holes with a pencil, then removed the top and pre drilled on the marks. I put the table top back on the lift hardware and secured it with screws.
Great build! I thought of a trick for mount for the folding hardware. Start by supporting the mounting plates with two scraps so that it is level with the top surface, then use two sided tape to temporarily lay on the top. Afterwards fold out the top to drill the holes and mount the screws.
Good idea!
The finger holds is a nice touch, nice job on the build! Definitely can be built without expensive tools. Keep up the great work as the goal is for us to continue to inspire others to build something awesome! 👍🏼
That’s right!
Thank you so much for this beautiful design. My girlfriend and I both work from home and our new coffee table is perfect for us! I used double sided tape on the top of the hinges (Alien tape) and it was just strong enough to lift the table tops and then it was easy to drill the holes, remove the tape and screw the top.The result was perfect on the first try and it didn’t remove any of the finish. I’m not promoting this particular tape at all I’m just happy I finally found a use for it! Thanks again for your video and plans you are a great teacher and very talented!
before putting the bottom on, turn the carcass upside down and mark the holes for attaching the mechanism, then attach the bottom and continue on.
Killer job man! Love seeing another Columbus maker crush it!
Thank you!
I was just telling someone the other day that I wanted to build a table exactly like this, but had no idea where to start. Then this video showed up today in my feed. Excellent job. I'm no subscribed and will watch some of your other videos. Thanks.
Thank you! Hope the video’s helpful for you
Great timing. Doing a remodel and was trying to come up with a table idea for the new sectional. Being single, I eat many ah meals at the TV.
I need to learn how to work as fast as you but thanks you inspire me to engage in a different style of woodworking
You are simply amazing. I love your videos and I am not woodworking creator. Thanks.
Fantastic work, dude! It really turned out beautiful! 😃
Well done!!!
Stay safe there with your family! 🖖😊
Thanks!
Super clutch table. Great work as always.
Thanks!
you are my favorite RUclipsr
Thanks :D
And designer
I use paint sometimes to transfer marks. Cover the bracket in paint around the holes and carefully set the top in place. Flip it over and mark the holes with an awl, then wipe off the paint before it has a chance to soak in
Really do love this design - perfect setup for a sofa like yours! The mid video add was actually a Disney + ad...they must have watched the beginning haha
Yeah I wish I was sponsored by Disney hahaha
Very clever idea. Well done. Paul from UK 🇬🇧
Thank you
Very beautiful work. Elegant and stylish. I love it!!
Thanks for watching! :)
Beautiful! Love your design style. My next coffee table needs a flip top!
Such a great video, thank you and well done. looking forward to trying then retrying this build !!!
Great timing. Was just looking for a coffee table project I could try.
what a fantastic looking table...love the design. keep up the great content/builds!
To mark the hole exactly to align the brackets to the table top squeeze a piece of cotton ball in to the holes and drop some ink on it. Lay the table top on top and there you have the perfect mark on your table top.
I like your table.
Thanks
Maybe this was mentioned, I didn't read ALL the comments.
I think you could save some alignment headaches with the lift-top mechanisms by changing the order of assembly a little. Leave the bottom out of the table until you have the top secured in place. This way you could just flip the table over and work on it from underneath.
That’s a good idea
As always, another great video! For the top installation, i would first install it like how you did, mark its actual size, then take it out to carefully trim to size. After that you already have the correct screw holes to reinstall.
Thanks for the tip
Another great video and project, Alex! I love the double lift and I know you mentioned wanting better selection for the walnut, but I really like how the top turned out!
Thanks Bruce!
I just found my new coffee table! This is an awesome build!
Hey! Did you end up building it? How did it go?
@@rajathygerlynhenry8931 I have not unfortunately. My friends shop got flooded at the end of the summer and he’s been rebuilding and getting things back in order. Once everything is up and running, I will definitely be!
1:56 That transition got me like 😮
Great build as always. Looking forward to the next one maybe with more angles, hehe. The queue of stuff I want to build gets longer every time I watch your videos. Your shop looking good too.
Haha thanks!
What's the trick for getting a good finish in the areas where you have glue squeezeout? Doesn't the glue fill the pores of the wood and prevent stain/poly from looking right in those areas?
Great build! I had the same problem lining the hinge mechanism and ended up referencing the holes like you have. Initially I used sharpened bolts through the holes to press the top down to get the position for the holes. Unfortunately I didn’t have the right size nuts so I had to use tape to hold the bolts in place which didn’t work real well.
I love this table , was wondering if hot glue on the brackets would be a good idea to have a temporary fix while you drill the holes, you have enough play at the beginning to use spacers and placing it , and at the end hot is easy to take off (only prob you might have some light sanding to do underneath but you would get perfect holes I think, just an idea , thank you for the plans !!
I’ve had success with lift hinges by attaching them to the top panel before ever attaching the bottom panel.
Great video and build Alex! I wonder if you could have done a clamped up dry fit without the bottom in place and then with the carcass upside down drilled the holes for the lift hardware?
You could do it that way. But I think that’s a lot of extra work. It might be a good solution though
Install the bottom of the case after installing the brackets and have it elevated so you can get underneath.
As always an incredible build!
Thanks mannnggg
Brilliant build.
How have the lifts held up? I am looking to do a fold over with these lifts where the table top can double in size by folding back over itself.
8:00
Solution:
Carpet Tape.
Bourbonmoth I think his show is called does this.
Used this for something else and it worked.
But maybe someone already said this. 😂
Nice video, I like the design of the table
Thank you!
I built one similar but it lifted the whole tabletop up and twards the corner.
Monted the same lifts diagonaly
Nice. Great work!
Thank you!
Awesome 👏
I’m new to woodworking and have only built “shop grade” furniture in the past. I would like to start sourcing materials for this project but I’m having trouble procuring the 1/8” x 3/4” x 50” walnut edge banding. Where could I find walnut in 50” lengths?
Hi, the “edge banding” I used was just walnut lumber I cut to 1/8” thick strips. You can get lumber from woodworking stores like Rockler or Woodcraft, or other lumberyards. You can join Facebook groups and ask people who live in your area for recommendations
Just a little bit of double sided tape on the hinges, lift up and mark?
Won’t work. The force to lift up the top would separate the two
@@BevelishCreations painters tape and CA glue? Might be stronger. 🤷♂️
Maybe I’ll try it next time. These things are kind of like soft close drawers that take some force to pull open. But the tops are much heavier than drawer fronts, so it’s got gravity and weight working against it too haha. But CA glue might be the answer! Thanks!
@@BevelishCreations yeah for sure. Not simple.... I've never worked with this type of hinge before. But is it possible to adjust the tension on them temporarily? So its easier to open? Then once it's assembled you can tighten it back up?
Not with the ones I got. Maybe more expensive ones have the option to adjust the tension. I’ll try the CA glue next time
Design the build of the table where the bottom panel can be left out. Then you can flip it over, lay it on the top and affix the mechanism through the bottom.
Very well done on video. I would add more time to the reveal. It is the payoff and everyone, not just yours, just breezes by the final. Make the ending more like Return of the KIng.
At least u didn’t say it’s like season 8 of game of thrones 😂
Could you put the bottom on after the top allowing you to flip the whole table over and screw it all from the underside, then attach the bottom?
No, there’s no way to control the sides
Are the hinges damped? Does it soft close into the lowered position?
They’re dampened, but not soft close. they don’t drop hard at the bottom
Beautiful, love the walnut, where do you get your walnut plywood from?
Thanks! I get them from either Woodcraft or another local lumber store
Use double sided tape, then mark the holes. Lift carefully
Great build! I have this exact same issue and I have been thinking about building a table like this. If I did not want the cubbyhole but just the whole long top to lift up, would it work the same or do I need a different lift mechanism?
It would work the same
luv the design and functionality! Are you sourcing from Woodwerks? They are my goto for Rockler stuff and wood.
Hey thanks I get my lumber from either Woodwerx or Woodcraft. Whichever one has the stuff I need
Few things say Greater Cincinnati like LaRosa’s Pizza..
I’m in Columbus :D
“Gave me a chance to put away my more expensive tools and get back to basics” in a video in which he uses rockler and festool for everything 😂😂😂😂
A dowel jig like this is as basic as it gets. Sorry I don’t have a cheaper set of table saw or circular saw just to show it doing the exact same thing
@@BevelishCreations I’m not knocking you for having nice tools. More power to you. Obviously, I wish I had those. You just make yourself look like a fool, if you call them “cheap” or “basic”.
No I get it. I was just talking about the dowel jig. Because I usually build with the Domino before this. It’s been over a year since I built this, and I use this cheap dowel jig more than the domino
Really want to build this, but keep getting an "ERROR 20" message when I try to download the plans. Can you send me the link please?
You’ll have to ask Rockler. I don’t have the plans :(
Cannot download plans
Great video, I'm going to give it a try! About how tall is the table lifted and not lifted?
Hey sorry I keep procrastinating about answering your question haha. It’s roughly 17” tall when closed and 25” tall when lifted
Are solid wood doors worth it?
Depends…
Alex, do you have a 3d model of coffee table for shapr3d? Thanks
I’d have to find it…not sure if I still have it
@@BevelishCreations thanks!
No problem. What’s your email?
I’m no expert but maybe leave the top oversized, then attach it to the lift, trace it then cut?
That’s a good idea
Please forgive my ignorance, still kind of a newb ;) ... at about 3:10 you're cutting the grooves for the pieces to lay in. Using a "dados?" ... is that just a router that you're suing a special name for... or is the dados thing the straight line you're using to make sure you don't mess up the straight line.
This looks like a build that's just challenging enough for me, and I have a sheet or two of better quality plywood in the garage that just might make this something I can take on this summer... just want to make sure I have my ducks in a row first ;)
No, a dado is the name for the groove.
@@BevelishCreations alright... onto google to clarify... thanks! (I'm assuming the router makes the dado?)
Yes
@@crossfitthrive A dado is a groove that runs across the grain, a groove runs with the grain.
“I’m not just saying that because I’m sponsored“ aka “I’m just saying that because it’s sponsored.”
Builds mad sick idk if youve seen but maybe remove your hoodie strings when building, it's mad scary as it can get caught on motorised things 😢
I didn't receive the plans 😩
Please contact Rockler
Would be awesome of there was an metric version. Not only Americans watch this videos
I know. I actually build with metric
@@BevelishCreations nice, so now is the right time to share ❤️
Send me your email. I’ll remake the cultist and send it over
Woodglut has very good designs and plans.
Some double sided tape could have helped
That works well for drawers. Not so much for these
You talk too much! And you only opened the top for like 3 seconds without showing inside hinge etc