FORD FOCUS MK3 BLEED COOLING SYSTEM. CAR OVERHEATS AIR IN COOLANT SYSTEM
HTML-код
- Опубликовано: 27 авг 2024
- FORD FOCUS MK3 BLEED COOLING SYSTEM. CAR OVERHEATS AIR IN COOLANT SYSTEM
If you have Ford Focus and you to bleed the cooling system on your Ford Focus MK3 we will show you that. We will demonstrate how to bleed the cooling system on a 2.0 liter engine and automatic transmission but it should apply to multiple engines since they use the same design of radiators. It is very important to bleed the cooling system every time you had a coolant leak, or your drained your coolant antifreeze for repairs such as radiator replacement, water pump replacement, and other. In this video we will demonstrate how to bleed the cooling system on a 2013 Ford Focus but the procedure to bleed the cooling system should apply to the whole first generation Ford Focus.
This video might be helpful on:
2012 Ford Focus How to Bleed The Cooling System. Bleed Coolant Antifreeze
2013 Ford Focus How to Bleed The Cooling System. Bleed Coolant Antifreeze
2014 Ford Focus How to Bleed The Cooling System. Bleed Coolant Antifreeze
2015 Ford Focus How to Bleed The Cooling System. Bleed Coolant Antifreeze
2016 Ford Focus How to Bleed The Cooling System. Bleed Coolant Antifreeze
2017 Ford Focus How to Bleed The Cooling System. Bleed Coolant Antifreeze
2018 Ford Focus How to Bleed The Cooling System. Bleed Coolant Antifreeze
2019 Ford Focus How to Bleed The Cooling System. Bleed Coolant Antifreeze
► Ford Coolant: amzn.to/2YuMEln
► NT301 Scanner: amzn.to/3b0EHa1
► Check out our Amazon Store for the tools and parts that we use: www.amazon.com...
► Our Website: mechaniclifesty...
► Our Baby Girl Channel: goo.gl/WiVs8Y
► Our Second Car Channel: goo.gl/XB6fHq
► Honest Product Review Channel: goo.gl/sMPQXk
► GoFundMe Link: goo.gl/pUife3
Our Most Popular Videos:
► Bumper Repair: goo.gl/XBe4Sh
► Missing Wheel Lock: goo.gl/5n4a5i
► Bearing Replacement: goo.gl/JSNDnZ
► Restore Headlights: goo.gl/qVhDkf
♦♦♦ Cameras & Gear Used For This Video ♦♦♦
•Cameras
Panasonic Lumix FZ300: amzn.to/2BNWtNA
•Tripod
Polaroid 72-inch: amzn.to/2iVTmP4
•Microphone
Polaroid Pro Video Condenser: amzn.to/2krpSsA
•Light
NEEWER 160 LED CN-160 Dimmable: amzn.to/2jjg9Bd
•Comuter for editting
Lenovo ideapad 310: amzn.to/2kqUNFl
♦♦♦ Other Equipment and Gear that I use ♦♦♦
•Camera
Sony HD Video Recording HDRCX405: amzn.to/2jk8nqB
•GoPro HERO5 Black: amzn.to/2ktNKfj
•Extra Computer For Editting
Lenovo Ideapad 510: amzn.to/2ktOuB7
► Like Us on FACEBOOK: / worldmechanicsofficial...
► LIKE & SUBSCRIBE for MORE DIY VIDEOS that could SAVE YOU BIG $$$$$$$ !!!
This is not a sponsored video. Everything is purchased by us!
The video is meant for entertainment purposes only. Do not Attempt!
AMAZON ASSOCIATES DISCLOSURE
Auto Repair Guys is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com
*Disclaimer
We, Auto Repair Guys, are not responsible for property damage or injury incurred as a result of any of the information contained in this video. Information given in this video does not guarantee the desired outcome. Any injury, damage or loss that may result from improper use of the tools, equipment, or the information contained in this video is the sole responsibility of the user and not Auto Repair Guys.
⛐ Check out our Garage to see what tools we use and recommend:
www.amazon.com/shop/worldmechanics
⛐ Subscribe and hit the notification bell by the subscribe button for new videos: ruclips.net/user/AutoRepairGuys
⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys
Would that be the same for a 2004 st170
Lu2111291525481=5411.22..====5
Hi, I’m a qualified Bosch technician and have been in the industry for many years.
I watched your video on fitting a new AC condenser to a 2.0 ltr Ford Focus.
Thanks for putting in the effort to list the video I found in quite helpful in completing the procedure.
I would like to advise you on a couple of points.
First, don’t try and dismantle the radiator/condenser/fan/air dam stepper motor assembly in the vehicle..too hard and you can break clips!!
It’s much easier to remove the whole assembly then dismantle on the bench.
Second, the hole and chamber under the air cleaner assembly is for backfire not to drain water from the air cleaner assembly. There is however a small hole in the backfire chamber to release any water that might enter the unit.
Third, avoid blowing compressed air into the cooling system,. Most cooling systems don’t have heater taps only air flaps so you can expand the heater core very quickly and cause it to leak.
Well done on your presentation.
David - Australia 🇦🇺
Thank you for all the videos you make I keep finding myself back on your videos over the years.
I can tell that you worked for ford....or someone that worked for Ford thought you how to do the 30 seconds sequence... unless you found it in the computer....good job
Shouldn't need to raise the car and disconnect that line. That vent tube goes to the top of the coolant reservoir and will air out for you.
I was thinking the same thing.
Thanks, I just had that little reservoir hose break while putting in a new MAF sensor. It dumped all my coolant. I limped it home and I'm waiting for a new one. This info is important.
@@Fifth313ment wish id known just how FRAGILE it was before leaning in to check all hoses, and for leaks! Yeah it's broke in like 5 places including right at the degas overflow clip. FML
I hate to ask, but am stuck in a Northerneastern city inMaine, frigid temps, 6 nights ago, (and after I popped the hood to my '14 Focus SE-and while cold, not started/idling- I topped off the coolant while checking other fluids, then replaced the cap. Started the car, and ran the vehicle (at idle to keep warm, as I was awaiting arrival from a traveling friend) for about 4.5 hours. During this time, operational temp remained halfway (190°F?), And car was blowing perfect, ste-temp heat the entirety of the almost 5 hour period.
We went for coffee, so I shut the engine off while in the coffee shop, [a good 2 to 3 hours] said goodbye to my friend, then went out and started my car. I let it run about 10 minutes
Now, not even 200 feet down Main St. I FIRST NOTICED IT WAS BLOWING COOL/COLD AIR ONLY, THEN IMMEDIATELY AVERTED MY EYES TO THE ENGINE TEMP GUAGE, {{since my informational LCD screen went kibotch [black]the first time my transmission failed completely, saying "Transmission HOT!" "Pull over to safety", right smack in the middle of the busiest intersection on Rte 1 Southbound, by what was once a decent shopping Mall and only had Neutral.)~this was around 92,000 mi.~}}where I watched the ENGINE TEMP QUICKLY RISE.
So I IMMEDIATELY pulled in to a parking area, and shut it off.
••~1ST QUESTION:. HONEST OPINION PLEASE:.......
WHAT IS THE PROBABILITY/ LIKELIHOOD THAT--
(+++EVEN*AFTER* IDLING FOR 5 HOURS, allthewhile BLOWING GREAT HEAT, AND REMAINING AT NORMAL OPERATING TEMP+++)--THERE IS AIR TRAPPED SOMEWHERE ???!
SO AFTER THE HOOD WAS POP I WENT OUT AND WENT AROUND to check hoses and check for leaks and when I leaned in to check to the lines and/hoses, for cracks , leaksgoing through the heater for four hoses rather and when I leaned in and broke (in several pieces) the overflow reservoir hose the (small line with clamp to radiator valve that you were adamant in the video on being careful, since it was known to be fragile)into in the video.
I am currently attempting to patch it the best I can in my dire circumstances (live in my car, btw)since it's a dealer item and I have to wait for it to be special-request ordered & shipped to our local Ford dealer and need to move my vehicle b4 it gets towed away.....Is standard, yellow, flexible air-compressor hose.
•••2nd QUESTION:.Just in your opinion, is this line okay to withstand not only the pressure, but the temp the coolant, as it's all I have at my disposal and/or engine can get?
Great info guys
Finally a helpful focus video , thanks man
Thank you for an Excellent video and description.
That’s not how you bleed it... the reservoir tank is the highest point in the cooling system. No need to pull hoses under the headlight. If the car is cold you should be able to start the engine and bleed it through the reservoir. Fill until no more bubbles and level is at max when at operating temp.
I have a ford galaxy and cant find bleed screws either. So I just turn the engine on with the cap off and the air will just bubble out that way?
@@schmo9425 yeah so fill up your coolant up to the max line, start the vehicle and let it run for a while. Keep an eye on the reservoir, you’ll see the level drop and some bubbles come out, add fluid as necessary until the coolant stop dropping and there are no more bubbles. Goodluck!
Thanks guys! Will try this once I've located and fixed the coolant leak.
@@schmo9425 no problem! I’d still try and refer to a service manual for your vehicle if possible!
@Siye Boss looks like coming from heater matrix/core!
Will that cause the fan to not turn on
Surely if you fill up to max, leave the cap open and run it, the car will push the air out anyway? So long as you keep an eye on levels and temps it'll sort itself out
Is there a bleeder valve on the transmission next to the battery? Saw a hose when changing spark plugs that doesn't seem to connect to anything.
Mines leaking what are the two pieces called ? So I can order new parts
My obd 2 tool reads sharps up and down on my coolant is it good or bad?
Good work freind
Thank's
At my car nothing comes out ? You have any idea why?
Is it the same way for 2013 ford except ??
The hose at 5:32 on my car won’t go all the way in. It seems like the part of my radiator isn’t deep enough to get the full clip in but the hose looks no different than this hose in this video. Help would be deeply appreciated
Hi Devin, how did you solve your situation ? I am facing the same issue
@@guillermocordoba8862 I literally cut the plastic thing around the hose and pulled it off up to the rubber washer. The thin part of the hose goes in no problem and the rubber washer and clip keep it in. Got my car running like new now 🤘 I was pissed that’s what I had to do tho.
@@devinzorn2077 thanks!!! for the tip !!!
My mecghanig did head repair gasket and still kosin coolant pls help
hello brother i had a problem with my ford fusion 2010 overheating,i changed my thermostart and burp the air out bt still the car is overheating,,any advice ..?
Hi just in the minute 5.23, you show how to plug the hose into the radiator, I had tu buy the hose, it is new, but when I try tu put it, I can't, any tip?, I think it is the same situation as Devin Zorn
Guys,guys guys 😂
Fuck off
What if that hose is broken? Would I need a whole new hose or can you replace part of the hose?
That's what I'm attempting to do w/ the aircompressor hose. (All I have at my fingertips, gotta wait on part from dealership
@beauthomson9944 I'll let u know how far I get with a patched up line
make a video how to change a radiator of a ford escape 2015 and bleed the system.
It's the same method like this
Fuckin adverts. Can't be arsed.
Cancer of a car
im confused. here you say you couldn't find an emptying valve so you removed the hose.
but in other video you showed a same car model mk3 focus with an emptying valve:
ruclips.net/video/kizluYWxzag/видео.html
can you explain?
I think they're referring to the bleeder port on the Ford Fiesta. So instead you have to pull this return line fitting.