As I was using my SE 979FSG flexshaft the entire chuck piece came out of the hand piece. Any thoughts? It never seemed to run hot. I've had the flax shaft for years but it probably only had 100 hours of use on it max. Then entire chuck just loosened up and slide out while I was doing some finishing work on a piece. After I watched this video that is that part you said never to mess with because it has been tru-ed to a certain point. Any thoughts on fixing it or is it probably just time for a new tool?
so if they are press fit on.....you cant dissasemble the handpiece at all, even after removal of the internal retention screw? My handpiece is making funny noises.....but is probably pre 05.
Hi, I'm from Colombia, I don't speak much English, but I have a handpiece and I was drilling and the chuck was quiet all over the top where the bits are put and I don't know how to put it for help, I'm new with one of these motors thanks
We have live chat on our website www.foredom.net . Try describing it in your own language and we will translate. Also please tell us exactly what tool you have.
Yep, it does look like they're likely a 608ZZ "skateboard wheel bearing" I design all small projects with 608 size bearings where I can. They are a very common size, very easily sourced locally for repairs, and an affordable way to "over engineer" any small project
The problem could be in the speed control. It could be either the trigger switch or the circuit board in the speed control. We sell those parts and you can replace the parts yourself. www.foredom.net
Хобби
Just what I needed, got my unit in running shape again cheers!
Wow !!! thank you so much for sharing this, I did need this information. 🤗
Thank you! It was very useful information how to open handpiece.
Well, that was Relaxing :-)
Man, I cringe every time you use those pliers without soft jaws on the QD. Other than that, I got a lot of good info. Thank you :-)
Some of us cringe, too.
My handpieces are we not analyze Please advise what to do to make it go dismantle thank you
what would you use foredom oil for?
As I was using my SE 979FSG flexshaft the entire chuck piece came out of the hand piece. Any thoughts? It never seemed to run hot. I've had the flax shaft for years but it probably only had 100 hours of use on it max. Then entire chuck just loosened up and slide out while I was doing some finishing work on a piece. After I watched this video that is that part you said never to mess with because it has been tru-ed to a certain point. Any thoughts on fixing it or is it probably just time for a new tool?
so if they are press fit on.....you cant dissasemble the handpiece at all, even after removal of the internal retention screw? My handpiece is making funny noises.....but is probably pre 05.
Hola lo arme asi pero no se por que se calienta 😢 si me puedes ayudar
Спасибо.
Sir plz mak a video for fordom hummer action hend pics repairing
Hi, I'm from Colombia, I don't speak much English, but I have a handpiece and I was drilling and the chuck was quiet all over the top where the bits are put and I don't know how to put it for help, I'm new with one of these motors thanks
We have live chat on our website www.foredom.net . Try describing it in your own language and we will translate. Also please tell us exactly what tool you have.
Does this H30 and H44t use the same flex shaft?
Yes.
that's a rollerblade/ skateboard bearing! what the!? i guess they're probably cheap and well made since they are so widely used though.
Yep, it does look like they're likely a 608ZZ "skateboard wheel bearing"
I design all small projects with 608 size bearings where I can. They are a very common size, very easily sourced locally for repairs, and an affordable way to "over engineer" any small project
Brasil
Why my foredom canot slow,?
The problem could be in the speed control. It could be either the trigger switch or the circuit board in the speed control. We sell those parts and you can replace the parts yourself. www.foredom.net
Hadir
That’s bad you know the bearings is the problem send back to you,maybe send to customer is better. It’s a good tool I need bearings please