Tips for Driving a Manual Transmission - On and Off Road
HTML-код
- Опубликовано: 6 июн 2024
- In this video featuring the AutoEdits Jeep Wrangler Rubicon JKU... I'll show you lots of tips and tricks on how to get the best out of a manual transmission vehicle... both on the road and off road as we hit a local trail.
00:00 Introduction
01:25 Proper clutch release technique
03:13 City Driving
05:13 THE MOST IMPORTANT TIP TO MAKING YOUR CLUTCH LAST!
08:48 Hitting the trail... off road tips
Thanks so much for watching, please make sure you are subscribed to the AutoEdits Channel and head on over to the AMAZON Store to check out the B&M Performance Shifter that I'm running on the Jeep or pick up a few of the other great items I use on the channel!
www.amazon.com/shop/autoedits...
Anything you purchase starting from the storefront helps support the channel... so thanks!
You can also head over to the Instagram...
/ autoedits_jason
And until next time... ENJOY YOUR DRIVE!
#jeep #wrangler #howto #manualtransmission 
Авто/Мото
That was an awesome video, Jason! Love my stick shift jeep, could definitely relate.
edit: B&M shifter is a must for sticks IMO, really enhanced the driving experience.
Thanks, glad you like the shifter like I do! How did you hear about it?
@@AutoEdits Thanks to your channel!
Your audio while driving with the top and doors off is far better than it has any right to be.
Another couple of tips I've experienced that may not affect you in warm sunny Southern California but do for us in the cold Northeast, even if you've warmed up the engine, the manual transmission doesn't really get warm sitting there in neutral. One trick I do is to throw the transfer case in neutral and then put the transmission in gear, I usually do fourth or fifth and then let the clutch out while it's warming up. This spins up the gears and shafts inside the transmission and gets the fluid warmer so the synchros will mesh easier when it's time to actually go. I've also found that if the transmission is cold that double clutching can help until it gets up to temperature.
This is great stuff! I've never thought about that aspect in the cold.
Absolutely! Cold weather means different warm up procedures. I also use the block heater when I park outside, and a small ceramic heater when I (occasionally) have room to park in the garage. The ceramic heater can warm the engine and driveline where the block heater only warms the coolant.
I have this issue here in queb3c. Getting into gear is tough colder than minus 10. I'll try this trick to warm up the tranny.
I just bought a 2 door manual rubicon 2 years ago. It was my first manual, I love it.
Heck yeah!
How's she holding up today
My dad taught me how to drive a manual when I was 16 years old. I'm almost 63 now, and still love it. I have a 2018 jl unlimited sport s and can't honestly think of ever driving a wrangler with an automatic. Great video and tips for the newbies out there!
Thanks!
Step dad also taught me at 16. Early on he took me to a driveway on top of a hill. He had me pull in and back out to go other way. As soon as I back out he would yell "there's a car coming" just to startle me. Dumped the clutch I think four or five times. Never dumped a clutch again in my life. Finally got another stick today after 15 years of not having one (98 4runner) and already having so much fun.
I learned how to drive a manual on my uncles TJ 4.0 in 2001 and fell in love and haven't turned back since!!! Every car since then had been a manual, even if it meant searching for months.
I now have a 23 2door Sport and can't wait to take it off road!!!!
Coming back to this video years later after just picking up a clean 2006 jeep wrangler TJ for my Jeep collection lol
Congrats on the new Jeep and thanks for the share... I absolutely love hearing this!
Your leave no trace advice earned you a subscriber. Thank you.
I appreciate that!
Hell of a vid man ! “Goood Stuff” 😂 16:45
HA! Thanks dude!
Every video you make I just can’t stop smiling. I have a manual Sahara as well and I love the manual off-road
Dang… I so appreciate hearing that!!! I’m smiling right now!!!!
Mahalo for validating the techniques I learned from the decades of manual transmission driving I've done! I miss that "in tune feeling" I had with my cars. Hydraulic clutches were the bomb for me, too! My Hondas got over 200,000 miles each out of their hydraulic clutches. My friend's Jeep had an Iron Duke 4-cylinder with a 5-speed manual and hydraulic clutch. Loved hill climbing in that. Never drove a vehicle with Hill Hold; Studebaker and Subaru had those. Thanks for the great video.
Great to hear all the stories! Thank you!!!
Awesome video. 35 Years of driving a stick (learned on a dumptruck) and I thought I was doing okay. Now I know even more and I feel like going out and climbing over some snowbanks. Cheers.
HA! Love to hear that! I keep learning all the time here... it's crazy. Now have fun out there in the snow!
I saw your installation of the B & M speedshifter. My 3rd gear kicks out, too. I was told I needed a new transmission & to drive it till I couldn't anymore. I'm glad to see you still like this shifter years later. I'm about to install mine shortly. Thank you Sir.
Yes... still happy with this thing. It does take some time to really get used to it but worth it for sure.
Great Video, it just popped up and I gave it a watch. I have been driving manual since I was 12 and I feel it keeps you more in tune as a driver. I have a 2010 JK auto and a 2014 Sahara Manual and it was just cool to see this video. keep up the great content.
Thank you so much for the support!!! Love hearing from you!
My current daily is a 91 f250 with the 460, 5 speed/4wd combo. perfect video to get my confidence up for offroading with my truck!!
Heck yeah!!!
Awesome stick shift tutorial! I have a six speed manual like yours, not a lot of offroading on it yet. The off-road stuff is definitely good to know because I’m not that experienced with a stick shift off-road. I want figure out how to run my lockers through my sPod like you have. Thank you for the tutorial!
Practice on easy trails and work your comfort level up! Would you like me to do a more detailed video on how I did the locker bypass?
@@AutoEdits yes that would be awesome!
We'll explained! We've got a TJ with a 5 speed and a JKU with a 6 speed. It is surprising how much different they feel when driving, but your tips apply to both Jeeps really well.
Right on! Does your TJ have the 4.0 engine? I really like those.
Just picked up my first Jeep. It's a 2 door manual JL. I've been all over RUclips looking for exactly this video. Thanks so much for putting it out. These tips will really help. Subscribed!
Howdy and welcome to the channel! Enjoy that Jeep!
Sir! I just got a 2door manual JL too! Hi 👋
Good video for those that didn't grow up with manuals. Even today's manuals are so much better then the old ones.. no synchro, double clutching. I went with 5.13 R&P gears and find that I don't have to slip the clutch nearly as often off road or on road.
I considered going that route but opted to stay 4.88 for highway / city / roadtrip mileage. For more serious off roading, you made the right choice to get the best out of this engine. Marco at OverlandX went 5.13 to tow his camper trailer and is very happy with that performance.
You made me miss driving my old 49 Ford truck with straight cut gears... loved that thing.
That was awesome and so much fun!!! Can’t wait to see the PSC install
ME TOO!
Great video as always! Lovin' the max quench in the cup holder. :D
Thanks and great spot!!!!
Thanks for the tips. Love your Jeep I also drive a Jk 3.6 manual and it’s really fun. Greetings from Puerto Rico 🇵🇷
So great to get a comment from you! Love to hear from fellow "man-pedal" jeepers!
Great video! I recently bought a Jk manual, and while I am familiar with a manual transmission, the off road driving has me wary... you made it seem so easy though! Thanks for the tips!
Great to hear from you! Have fun out there and the biggest tip I can make is to just get out in the dirt and see what works best for you. I just got back from a week in Moab for East Jeep Safari and found myself having to re-learn many techniques for actual rock crawling... it was scary but fun!
Brake drag technique is new to me, added to the tool box thanks.
You bet! Thanks so much for being here!!!
Yet another great video with some great tips. I've been driving sticks (that's what she said... right) all my life and I've gotten into the habit of resting my hand on the top of the shifter.
My wife enjoyed all your advice on and off road tips.👍
Yeah buddy! Don’t torture your poor wife with these silly videos 🤣 please give her a high five from me for putting up with this!!!!
@@AutoEdits We enjoy watching your videos together. You explain things very well. You and I have similar outlooks so we say the same thing. She understands the way you say it though. Haha...
Plus, she's seen a lot of your Jeep build videos because I modeled my build after yours. You did a great job!
This video was really helpful and I learned a lot on what to expect. My dad is planning on giving me his 97 jeep wrangler tj when I get my license, but I'm doing a lot of research. One tip he told me was to not be afraid when driving stick.
Awesome to hear!
Tj’s are easy to learn on. nice and torquey motor and a smooth, light clutch
Super smart trick on left foot braking. I never thought of that for offroading
Hope it helps... always fun to try new techniques!
Great tips! Never thought of dragging the brakes like that to keep the open diffs from spinning up dirt. I'll have to try that on my next trip out.
It really helps me get the most out of the Tahoe and just calm down the Jeep on loose stuff. Thanks dude!
@@AutoEdits this works great when starting a donut with my truetrac
@@jacobchandler2083
I was going to mention applying the brake helps my truetrac grip.
I’m still trying to wrap my mind around how this helps. Theory that it just puts a bit of resistance on the wheels with the least traction, encouraging the ones with more traction to have more relative power to the wheels?
Love the video - thanks for compiling so clearly.
That's my favorite way up to the top of the flats! Great local spot that's way less trafficed than the Rawher trail.
It sure is! I can't believe I missed this turnout when I took my Tahoe up there... this would be a fun challenge in that rig.
Just got a 2005 Ford ranger 2WD manual. Been really enjoying building her up, thanks for these tips!
I love that year Ranger … almost got one when I was buying the Tahoe but they were too expensive 🤣
@@AutoEdits would’ve loved to see ranger build! They really are pricey, got it for 4k but needs some TLC 👍🏽
I wanted it so bad but the guy wouldn't budge on price and the Tahoe was $800...lol
Congratulations chief
Alway enjoy your videos! I have a 2015 JKU, I run 35's and 4:56 gears. It's a six-speed manual. It always feels like it has some interference getting into each gear.
Never just a smooth transition. I bought it new, has about 92,000 miles on it now. It's never been abused, or rock climbing mostly mellow trails and hill climbs.
Thank you for the dragging the brake tip! I'll definitely try that when needed.
Howdy and thanks! Have you ever checked the level of fluid in your manual transmission? I found that my Jeep from the factory had less than half a quart and once I flushed and filled the full 1.6 quarts (plus just a bit) the transmission felt much happier. I did end up going with the B and M shifter and once I got used to that... enjoy it more as well.
@@AutoEdits Thank You, I'll check it out. I've watched your install of the B&M Shifter a few times, I've been kicking it around to do the same. Yours seemed very stiff at first but I'm sure has loosened up since then.
@@drivesideways6550 If yours doesn’t unexpectedly pop out of gear than there’s no need for the b and m unit.
Your video's are made as well as a television show. Great job.
Thanks! 😃
Thanks Jasen love watching your build and thanks for giving me an idea on what gear I use in my 6 speed manual going up some hills I have coming up this weekend I used to just do my thing but at 63, I needed a refresh course.Thanks Brother
I'm the same way dude! Thanks so much for the encouragement and I hope you have a great trail run!!!
Thank you for your suggestion for the B&M shift lever for the transfer case.It sits a position that is natural.I appreeciate your advise.
Glad it was helpful!
Thx for that video, love it!!!! 😍👍🏻
Glad you enjoyed it!
Thank you for hovering clutch tip, one thing I’ve wondered the most
Happy to help!
This video was fantastic!!
Thanks!
Awesome video 👍.I learned how to drive a manual from my grandfather at the age 8.
That is awesome!
Badass video this deserves 10 million views. Keep it up!!
Hey thanks a bunch!!!
Enjoyed it very much , nice jeep.
Thanks 👍
Great run down!
Thanks!
Great video. 👍
Hey thanks!
good maneuvering that Jeep baby!
HA! Thanks, that thing just drives like a dream... even better now... check this video out when you get a few minutes ruclips.net/video/4IPG9_IoJ6g/видео.html
Great Job!
Thanks!
Great job. The split screen/ multi angle views were cool to see. Appreciate your hard work. Only thing missing was Pinto!,
So true about missing Pinto... but since her leg surgery... she really doesn't like getting bounced around in the back of the Jeep and the half doors make me nervous with her back there. So she hangs out with me on the trails close the house! Thanks for watching!
I learned how to drive one on non synchronized transmissions. Those seem to be harder to learn on because you can't just push the clutch in to go into any gear you want. Some of those clutches that aren't hydraulic feel like you're trying to do leg day at the gym.
Clutch doesn't need engaged in 4lo, only to change gears. If it stalls in 4lo, no clutch start and go. Can find the video from a jeep event and they explain it to the driver. Suppose to help keep mud and junk out of the clutch if stalled in water.
Do you drive a manual Jeep?
I never push in the clutch to start in 4 low.
@@AutoEdits not trying to prove anything it is just another option, thats why starting with the TJs they had it in the owners manual how to disable the feature to have the clutch engaged in order to start it. It is really easy on the drive train in 4 low 1st gear.
@@lewy1 Cool
Just went to hungry valley yesterday and definitely gotta tweak my stick shift skills a bit. Kept bouncing back and forth on the pipes and rocks..
Only way to stay good is to keep doing it!
Idk how many times I’ve watched this video lol still stalling on some obstacles
that was a super awesome video Jason. the roll through stop sign is not very well tolerated up here, they hand tickets out for that ;-) I will try the drag the brake technique too. super good information. Looking forward to more clutching tips in 4 low
Oh, I always come to a full and complete stop... that was just an illusion and I was mentioning the technique of putting it into first just before coming to a full and complete stop. 😅
@@AutoEdits duly noted Jason! I'll probably re watch this video 10 more times!
Great video, Jason! I have a 2 door JK manual I ordered from factory. I now have 85k miles. Just did my rear main seal due to mud ruining it and figured I would replace the clutch while in there. After so many miles, my clutch was only worn .030"! It was almost not even noticeable wear compared to the new one. I thought I was a decent manual driver, but with wheeling and city driving I thought the clutch was pretty cooked. I was happy to see that how I was driving was the "right" way.
Glad to hear this as well... did you replace the clutch with a stock or aftermarket unit?
@@AutoEdits Stock replacement. Jeep used Sachs and Luk from factory. Mine had a factory Sachs, I replaced with Luk as well as the throwout bearing and slave cylinder. Feels just like new. A little controversial but I did not resurface my original flywheel, it still had factory machine marks in the contact area and no noticeable wear running a fingernail over it.
Sounds like you are really good with your clutch use!
When did Jeep begin offering automatics? Excluding the Jeepster... I think it was in the mid '70s cj7. Wasn't it? I think the cj5 never had the option.
@@xmo552 They had automatics in full size jeeps and trucks in the 60s. The CJ-7 was the first regular jeep to get an automatic. The CJ-5 was simply too short of a wheelbase to fit in an automatic, every one is manual from factory.
Jeepers uniform. Hat flannel shirt, jeans and hiking boots. Haha, it's the same here on the East Coast. Good vid man.
So true... love hearing from fellow Jeepers on the other side of the country!
I have an 88 YJ with an AX 15 conversion. When stopped on a steep hill to get going again I installed a hand throttle so I don't have to do the brake, clutch, throttle pedal dance.
solid technique
If you give it a small rev before you push the clutch in, will allow it to go into first gear easier. Or got strait to second and then into first. Good advice to folks on being gentle pushing into and coming out of gears.
Great video! Some future video suggestions: clutch service or ebrake adjustment? :). How can you tell if it’s time to service the clutch? My Jeep manual is coming up on 80k
These are really fantastic suggestions… thank you!
I have a 12 JKUR. My first manual vehicle. this video would have helped a few years ago lol
Well, I'm a little late but I'm glad you're here... LOL
The Peugeot trans in my 88 Comanche is crying for a swap out. 1st grinds coming out of a stop so coming up to a stop sign instead of going full neutral to 1st.... I'll shift it into 2nd and 1st like you do. That helps immensely.
I won't mention all the other probs this transmission currently has.
Yikes!
Great tutorial! Having a stick makes it a lot more fun on and off-road. I appreciate the advice about keeping foot off clutch. It's something I need to work on, especially since I just got a Centerforce clutch and B&M shifter installed.
How well does your parking brake hold the Jeep? I don't trust mine at all and it's an area that worries me when off-road. Maybe a follow-up video on improving it?
I'm really curious about the Centerforce setup... how do you like it? I'll add a parking brake check up video to the list! Thanks!
Pedal feel is better. Smoother engagement. Took about 500 miles to loosen up.
Cool to hear this, thanks!
2010 JKU with a 6sp manual, 5:13 gears & 40s on Dana 44 here… we had 4:88 and 37s for a trip to Moab and being the only ones with a manual we were nicknamed the “reverse ranger” since we usually needed just a stitch more runway to get the jeep into gear before the obstacle- overall we had an absolute blast in our first adventure really wheeling (we live in Michigan, so we have Sandy hills here- that’s about it)
I deeply appreciate this video and wish I would have seen it in like august of 2019 😜
Next step will be 6.0L LS + automatic for project Raven.
One last note- No wheeling alone! Isn’t that like the first rule of off-roading? 😉
Great video! 4Low is such a beast. Climbing steep hills in 4low my Jeep is almost like driving an automatic. I also love the constant steady speed of 4Low going steep downhill - no clutch, no gas just occasional brake. JLUR 6spd 5.13 37's
Totally agree!
I like your way of driving boss
Thanks!
Thanks for this video. I'm a 1st time Jeep owner, and mine has the 6-speed manual transmission. It's been since the late 1980's since I've driven a stick. I have 35's on my 2 door, and I wasn't sure about running the transfer case in low. That makes sense! I really liked the sound of your Jeep. What exhaust are you running? Thanks again for the vid!
Congrats on your manual Jeep! I’m running the magnaflow exhaust and love it! ruclips.net/video/oV8w2zQAOHk/видео.htmlsi=e_fYQD5R6o2ySVKc
Manual. Makes driving to the corner store fun.
Ha! So true
Hahaha...after 30 years on the internet I learned how to comment on a video I like....haha...this is what I wrote...haha. Love my 6 speed JKU. Looking forward to replacing gears or axles to re gear for larger tires.....So happy to leave a comment f it.... Jason, love your channel. It took me 4 years to learn how to thank you for your content...oof. Also I miss Marge and love to see Pinto. Good choice.
Ummm. How would I know to look for replies or someone busting my balls because I just learned how to use the internet...😓🤦♂️🤢🤮
I’m really glad you conquered the internet as well… maybe you can give me a few tips! Howdy and welcome to the comment section!
I am having the same issue with the steering especially when air downed . I just ordered the full PSC cylinder assist kit and I was looking for installation instruction video but couldn't find one which is detailed. you make really good and easily understanding installation videos. when are you doing the install for the PSC system ?
I am looking to do the install this weekend and I'll edit and post it as soon as I can after that... maybe by end of next week! Good choice... this kit is such quality components!
That Sounds good. please go in little detail about how to mount the PSC reservoir without cutting the factory air box on jk and how to position the pitman arm correctly on the new box. and where to position the Steering Assist Cylinder on the tie rod side. Thanks
I keep my hand entertained on the stick all the time. Haha
😂
Hi Jason! I love this video, I was wondering if you have had any issues with your B&M shifter lever? I had had the two shoulder bolts break twice on mine and the lever starts to spin. I’ve seen others complain about the same issue, just wondering if there is something we are doing wrong or anyway I could keep that thing lasting for years rather than 1 single year. Thanks for your help!
I did break one of those but they sent new ones on request and I’ve been on them for a couple years now. Wonder why they keep breaking on yours… e-mail them and ask.
I have driven manual since I was 14. (don't ask) My wife learned to drive her new at the time 2001 Special addition Yellow 2001 Saturn SC2. Both of my kids and my nephew have all learned how to drive stick on that same car. It is now my daughters car who started out in the back seat in a rear facing infant seat. Both are 21 years old. It has 300k miles and the original clutch. Anyway after many years of driving an auto 2011 JK i traded it in on a 2016 JKU 6spd. That hill assist takes some getting used to. I keep overrevving it. LOL Yes my beautiful wife, our son and our daughter keep messing with me. Due to having a take home car from work I only drive it on the weekends or days off. I have not taken it off road yet. Unfortunately the day before going to Uwharrie for the last opened weekend, the oil filter housing/oil cooler decided to start dumping oil. So instead that Saturday I spent changing that. I'm sure it will be a learning curve.
Growing up, CJs and Wranglers were always a vehicle I just associated with manual transmission. Like a muscle or sports car. To me, it feels “wrong” if they’re automatic.
I feel ya… but the new ZF8 automatic is really really good and I would get that if I bought new.
I really miss my stick TJ. It was just a visceral experience.
That is a great platform… TJ ‘s are awesome… glad you’re here!
awesome🙃
Thanks for watching!
@@AutoEdits I had a XJ with 4.0 and manual transmission, long gears (3.07) and 32 tires, and for me that was a ideal config for all my tasks. Im very agree with you about emotions and feelings of the vehicle with stick, It can give you moree freedom, but asks for experiense
My Jeep is automatic, and I do know how to drive manual (on the street), but I have been asking myself how to drive manual when off-roading… should you always use 1st gear?, second? When to use each one? How to change gears in a climb? Should you go downhill on gear or neutral? It’s just so different from automatic that I feel I don’t know how to drive manual when off-roading!! Have not seen a video like this before!!! THANKS!!
That is awesome!
You got the like and the subscribe for the "Thats what she said"....
Love to hear it... LOL... Howdy and welcome!
Although your video isn't Jeep specific one thing to mention is a Rubicon can be started in gear in 4 low without using the clutch.
WHOA! I didn’t know that! 👍
Great tips. But what about getting stuck on a rock or uphill having to hold brakes and quickly releasing to get up hill without rolling back. Need those kinda manual tips. Like the ones you gave but wanna see others
Okiedokie!
I want to upgrade my 4wd select shifter like yours. I cant seem to find one. DIdnt you have a video on that?
Yep, it’s in the Amazon store as well but here’s the video Jeep Wrangler JK Transfer Case Shift Handle Swap How To - B & M
ruclips.net/video/-vlZ5huJjCY/видео.html
Perfect, just sold my auto xj for a 5spd.
Welcome to the "man. pedal" club... (man. short for manual, we don't exclude the lady's around here... especially since I know a few that could out wheel me...LOL)
Great stuff! I've been looking for something like this. I've been driving a manual most of my life (my dad was adamant that I learn how to drive with a stick shift car). I've never driven 4WD, though, and I recently bought an older 4Runner with both manual and 4WD (love it!). I've done most of my off-roading in 4H and just assumed 4L was to be rarely used. I read a post recently on FB, though, where the guy mentioned using it often and shifting as high as 3rd/4th gear while in 4L, so I realized I've been missing out on some "strategerie." A couple of questions:
1) at 13:50, you started driving in 2nd gear (in 4L) from a dead stop. How did the car not die? Is that a 4L thing that allows you to have more clutch "grace?" If so, I could have used that going over some large rocks on a hill recently (I was in 4H and kept stressing the clutch trying to get enough gas to lift me over) (finally backed away after some serious lugging).
2) what are the recommended MPH and RPMs (in general) for switching gears while in 4L (I don't see a reference to that in my owner's manual).
Looks like a great place to wheel, BTW. The lake in the background is really cool.
Thanks!
Howdy and thanks! For your questions, 1) the lower the gear the more leverage the engine has over the drivetrain and 4L 2nd is plenty low. 2) the rpms dictate what gear you should be in. Most vehicles are set up to run through the gears in 4L at a top speed of 15-20 mph and then 4H for faster then that. The best thing is to just get out and practice in all the gears and see what you get comfortable with!
@@AutoEdits makes sense. I just changed the gear oil in my transfer case and drove around in 4L to lubricate the gears, and I ended up in 3rd gear around 15mph based on engine torque and RPMs. Seemed so strange, but I can see that being very helpful when maneuvering.
Thanks for the reply!
i have a 2015 JKUR 6speed, 2 questions
if your off-road, on anything more than a groomed gravel road, are you in 4Lo?
have you ever experienced any binding / ill effects of shifting through the gears below 20mph in 4Lo?
@@AutoEdits
Your rear driver's side shock sits more towards the bottom than centered top to bottom. Will checking the nitrogen pressure to make sure they are equal top and bottom fix that?
Sometimes that helps but sometimes one shock will just do that… drives my OCD absolutely crazy but the shock works completely fine.
What is your t case shifter? I have a 13 jlur built similar to yours, but with a tremec 4050 hd 5 speed swapped in. I also have a psc titan steering box without an external ram. Do not overdo the braking to control wheel slip, I broke parts on a yj doing that !
That's the b&m trans shifter ruclips.net/video/-vlZ5huJjCY/видео.html ... What is better about the 4050 over the 6speed?
About to get a manual 2016 wrangler, just wanted to know how hot these manual transmissions get when on the trail. I know a guy who says his middle console (where the shifter, cup holder, etc) feels like it’s going to melt because of the heat coming from below. Any truth to that?
Maybe for him but not for me... at all.
7:10 you should have put a mic in there, you can hear the Clutch grinding a little when you rest on the Clutch pedal. Or maybe that's just me and i need a new one, but yeah, get that foot off the pedal. It's not a foot rest lol.
No grinding, just wind noise. If you hear grinding when holding the pedal in... generally that's an indication the throw-out bearing is going bad.
Did you wire up the DRL function for the J3’s? If so/not a thought on how? Run to the fuse box?
I didn't even know that was an option... I'll look into that! Any info you can point me to?
@@AutoEdits All I know is the turn signal stays on for the DRL (in white not amber of course). Would look cool, still waiting on a response from JW about it.
Please let me know what you learn!
On a manual transmission, I’m stuck in the middle of a real steep hill, my FJ would stall every time I try to go up. Any tips?
Give it more gas and slip the clutch a little more. Use the parking brake to hold the vehicle while you get rolling and then release it once going.
Would you mind sharing which socal trail that hill climb was from?
Absolutely! That is the climb to Rowher Flats from Bouquet Canyon Rd. Let me know if that does if for you.
@@AutoEdits you're a king! Thank you, sir!
The vehicle manual in my jk says to have the vehicle in gear, clutch up, going 2-3 mph to shift into 4lo, but I can't get it to go into it, it just makes grinding noises. is having the vehicle in neutral, clutch up, and stopped the proper way to do it?
Do whatever doesn't grind for you. I rarely shift into 4 low while moving. There have been a couple times it would grind enough that I simply shut the motor off for the moment of shifting and then started it up and continued.
Do you have anywith the centerforce duel friction clutch?
I would like to try that for sure.
I finally might be buying an ultimate Dana 44. I am beyond ecstatic at the idea of upgrading my Jeep! I wonder how much I can sell a Dana 30 with 3.73s, maybe 10 grains of dirt? 🤔
Hold off on that UD44 purchase for a bit... depending on how much lift you have... I might have an even better recommendation. When I was was at 3.5" lift it was perfect but now that I'm at 4.5" it feels like the track bar mount is not quite high enough to eliminate bump steer. It's pretty dang good, as you can tell from this video, but I'm very picky when it comes to that stuff. So, I'm doing some deep dive research right now and finding the Fusion Elite 44 has a few more features than the UD44 but it is a bit more expensive. So if you can wait, I'll do a side by side comparison.
@@AutoEdits I’m around 3.25 inches of lift on my 2 door. From my Metal-cloak 2.5. Does the UD44 allow for more caster than a stock axle? I like a bit more caster angle for the steering feel but of course my drive shaft does not like over 5.5 caster. Regardless I look forward to seeing the comparison!
@@AustinH7 That would be just right for the more cost effective UD44 and yes... I'm running 7 degrees of caster right now and it feels great.
@@AutoEdits awesome! Yeah, the UD44 is on sale on Amazon for a pretty good price so I’ll probably be going that option. I still would like to see the comparison video!
Is this the axle you were looking at on Amazon www.amazon.com/dp/B01KHLG3HK?ref=exp_autoedits_dp_vv_d
I can't believe that price!
What would be the best cluth for a 2017 rubicon?
I'm still on the stock clutch but next week I'll be touring the Centerforce facility in Arizona and get a good look at that setup. I'm really interested in their "high inertia" flywheel most of all.
link for seat covers please!
There's a link in the description of this video ruclips.net/video/WHOHvf9HxQM/видео.html
I’ve been wheeling my 5 speed tj hard for the year I’ve owned it. Idk why I’m watching this lol
I'm glad you did 👍
We get it. You like playing with the tip
More like the ball...
👍👍👍
Howdy!
PLEASE PLEASE PLEASE.... Wheel size, make, model, offset and backspacing.
I want those!!
ruclips.net/video/VIQOF6n1-bg/видео.html
It’s unfortunate that many of the auto manufacturers are doing away with or severely limiting manual transmission options. It will be the loss of a great driving experience.
I honestly think the right vehicles will still have the manual availability but the sales drive the production so we're stuck with what people actually buy. I'd like to drive the new Bronco with a manual just so see what it's like but I was so happy with the ZF8 automatic in the new JL Jeep that I'm pretty good if that's my only option. Seriously.
where can i find those doors
I don’t think they sell them anymore. Bestop core doors.
Challenger manual has a dead pedal but it's trash because so narrow
Which seat covers are those?
PRP I did a video about them ruclips.net/video/WHOHvf9HxQM/видео.html
I just bought a manual Wrangler Wyllis. When I first drove it, the top of my boot was hitting under the dash preventing me from lifting my foot up. My boot is about 1 foot high. Is this normal to have problems with boots and shifting or is it my style?
What kind of boots?
@@AutoEdits They look like cowboy boots with a broad steel toe. I got them from Tractor Supply. It's the top leg part that hits the bottom of the dash when I go up and down on the clutch. Am I being a D-bag or is this a common problem?
@@AStanton1966sounds like you’re sitting too close. Move your seat back a few inches.
I'm 6'1"; I recheck the seat again; I thought it was back all the way. Thanks.
@@AutoEdits I just checked, the seat is back all the way. Maybe I'll have to adjust how much foot is on the petal.
👍
Howdy!