Exactly, on my regular mobula6 voltage dropped to 3,4V from 4,35V instantly on these lipos. Lipo sag was huge and it was hard to fly. But with this build they have much easier life and less sag, more performance ;) Even more benefits if you have big amounts of weak 1S sticks :)
So awesome, it is a rocket 🚀 i have a mobula 7 v2, it has GEPRC SPEEDX2 0802 16000kv motors, do you think these could be good for same satup you have? I have the estock fc too, by the way could you please share prop specs, like what pitch those are, i need 40mm prop but not sure what to buy so would like to test the same you used on this build
Props are gemfan 40mm they are very good on 2S High RPM with low pitch. Your motors are also pretty ok, so you can check if your FC supports 2S just change pigtail and send it!
@grox3857 excellent, thank you so much, for the moment I have been just using 2s, I will buy the gemfan 1610 biblades to test them, do you think will be ok?
Before you spend a penny, get a simulator. Fly in a sim until it becomes a second language for you. Then go rip a real kwad. In the long run, it'll save you tons of time, frustration, and money.
I have to ask you something man. I fried my esc board on my tinyhawk (the tinywhoop one) and the replacements are 80 euros, too much. Could I use another board like your one here into my tinywhoop? the tinyhawk use a all in one board, does it means that vtx and main board are not separable?
Yes you can use different board but need to set it up and also pay attention if it have vtx or if you need to buy as a separate when aio doesn't have one
@grox I am new to fpv drones, I bought a TinyHawk 2, I dare not fly it, did you use simulation or went straight into flying, what is you're opinion, should I do simulation before flying in the open empty field ?
@@grox3857 What do you think if I buy a cheap brushed micro/mini/nano drove for like £20 and fly that in a open field rather then simulator perhaps this would work, what do you think ?
@@monkeytridentOf course. Even my first ever drone more like a toy. For 10$ (furibee f36) Had a great time with it, learned throttle control and LOS orientation.
Since a lot of the parts are not available anymore now, what other kind of combination would be good for 2S setup, im not really sure what parts would fit together and be durable.
@@brechtxbrecht 2S AIO(from the video), MIcro lightweight VTX (ovx300) Currently motors are not available, so you can pick these new ice blue 0802 from betafpv kv range from 13kkv->15kkv
They don't need to be the same brand, you can install something different, tx port don't even need to be used, then you will set power and channel on the vtx via button but not betaflight
Old Mob7 Had F3FC With more grams and less efficient, also harder to PID Tune correctly. Motors fall apart very easy. I had very simillar whoop, then built this beast :)
I don't know about that. The old mob 7 was STUPID heavy. By that logic, all whoops nowadays are just a blade Inductrix with different components. This whoop is crazy cool. 21 grams, in a 75 pro frame. Wild.
@@sakfpv8444no the frame he use is 75mm not 75pro frame it is imposible to get 21 grams on 75pro I have one but the weight is 24 there's nothing you can do to make it 21grams
Yes, they are discontinued, very unfortunately because old version is more durable than this new shiny edition. But you can still buy them from official BETAFPV store for less money, so hurry up ;)
@@kratzeni Not good, so we need to use new 0802. Pick similar kv from 10k-16k max for 2s Voltage and also with ball bearings, this is important for high rpm performance. They are more expensive, but no other options on the market right now unfortunately
@@butterflyfpv But you can get these older updated Beta 0802 motors at very low price from official site. And durability is very very good, still no need to replace them and whoop is operational ater a lot of packs and crashes it has been trough :)
Maybe 9mins but it will feel more heavy and not fly as good. I think these 380mah gnb's are close to max weight that fly very well, maybe 400mah for two of these lipos to have 2s max. In bigger lipo you will gain more flighttime but whoop will fly worse and crash harder. It's always a trade one way or another.
Range is pretty baterry limited but 2-5km for the rf links used, and more if you swap better antenas for example foxeer lollipop micro for VTX and Immortal T For the ELRS
Wow you’re such an amazing pilot. I can’t manage to fly like that indoors on my 2s tinywhoop.
Love it! Great flying as well. Can't wait to see the build vid.
I'm subb'n ya bro!
Thankss! This build vid is on my channel :)
Very nice, thanks for the build info, this looks like a great way to use all my bad 1s packs, good tip, thank you.
Exactly, on my regular mobula6 voltage dropped to 3,4V from 4,35V instantly on these lipos. Lipo sag was huge and it was hard to fly. But with this build they have much easier life and less sag, more performance ;) Even more benefits if you have big amounts of weak 1S sticks :)
@@grox3857 very good to hear thanks
that voltage drop is pretty impressive, very steady and slow.
Yup, more tho with OLD lipos, current when hovering is only around 2A
Brother, you're one helluva ripper - Definitely deserve WAY more subs. Stay up bro ✌️
Thanks!! :)
Nice build. And strong pilot skills, that`s nice!
Thanks!! :)
Wow nice man! Do you need to tune it? Or is the Flight controller already tuned ?
Runs pretty good on stock PID"S
@@grox3857 so this means, when buying fc there are already stock pids preconfigured?
@@alenbrk1368 Yes, you will only need small tweaks, Connect to the ESC Firmware thru ESConlineconfigurator and set it to 2S Mode preset
Great video, congrats!
Thaanks :)
Sick, I’m building something similar rn ❤
I Wish you success, and fullsend! :)
Awesome video! Sorry, my question is, can I mount a flysky fs-ia6B to tthis drone, even if it will fly bad?
Get the smallest reciever possible and it could be possible
nice. could you run 45mm props on that frame too right?
40mm props, 45mm on meteor 75 pro frame yes
i love this man
Hi. This Launch control stand from beginning is your design or it could be find on the internet?
Own Model and 3D Printed
@@grox3857 there is a chance for sharing stl file or it is not possible?
So awesome, it is a rocket 🚀 i have a mobula 7 v2, it has GEPRC SPEEDX2 0802 16000kv motors, do you think these could be good for same satup you have? I have the estock fc too, by the way could you please share prop specs, like what pitch those are, i need 40mm prop but not sure what to buy so would like to test the same you used on this build
Props are gemfan 40mm they are very good on 2S High RPM with low pitch. Your motors are also pretty ok, so you can check if your FC supports 2S just change pigtail and send it!
@grox3857 excellent, thank you so much, for the moment I have been just using 2s, I will buy the gemfan 1610 biblades to test them, do you think will be ok?
@@TheFpc20 Yess, they spin MUCH faster on low pitched biblades, this is also the reason why I choose them over triblade, mentioned on the video also.
@@grox3857 thanks!
do you fly angle indoors in that fast flying? and rates for that flight?
I have Mr.Steele rates and all acro mode :) I only fly angle in LOS
@@grox3857 ok thanks but which steele rates :D there are many in the web.
@@alperenozgurI have RC Rate 2.00 Super rate 0.65 expo zero (And there are Betaflight) it gives max motion above 1000deg/s on full reach
for a beginner, what kind of drones you recommend for a start? Should i buy cheap E010 or anything else ?
Before you spend a penny, get a simulator. Fly in a sim until it becomes a second language for you. Then go rip a real kwad. In the long run, it'll save you tons of time, frustration, and money.
@@MrGaussFPV Thank you sir! I will take your advise.
I have to ask you something man. I fried my esc board on my tinyhawk (the tinywhoop one) and the replacements are 80 euros, too much. Could I use another board like your one here into my tinywhoop? the tinyhawk use a all in one board, does it means that vtx and main board are not separable?
Yes you can use different board but need to set it up and also pay attention if it have vtx or if you need to buy as a separate when aio doesn't have one
@grox I am new to fpv drones, I bought a TinyHawk 2, I dare not fly it, did you use simulation or went straight into flying, what is you're opinion, should I do simulation before flying in the open empty field ?
I had at least 50H in simulator
@@grox3857 Can you let me know which controls you use, left stick up/down left/right, and right stick up/down left/right cheers.
@@monkeytrident Standard Mode2 wich is Throttle and Yaw for left stick, Pitch and Roll for right stick
@@grox3857 What do you think if I buy a cheap brushed micro/mini/nano drove for like £20 and fly that in a open field rather then simulator perhaps this would work, what do you think ?
@@monkeytridentOf course. Even my first ever drone more like a toy. For 10$ (furibee f36) Had a great time with it, learned throttle control and LOS orientation.
great skill
Thanks man, just don't stop flying and skill with less crashing will come to anybody, matter of pratcice :)
Very nice video! This gave me some very nice inspiration, is there any chance I could pm u about some extra information?
Thanks! No problem you can ask questions here, so other pepole with similar will also have answer
Since a lot of the parts are not available anymore now, what other kind of combination would be good for 2S setup, im not really sure what parts would fit together and be durable.
@@brechtxbrecht 2S AIO(from the video), MIcro lightweight VTX (ovx300) Currently motors are not available, so you can pick these new ice blue 0802 from betafpv kv range from 13kkv->15kkv
Thanks!
Why only 2 screws mounting the motors?
In my tests with this tempo of flying no problems with durability, less weight.
What battery did you use?
@@michaelblake3320 Tattu 300 mah bt2
How do I know if one component is compatible with another? like if one cam is compatible with another??? do vtx and aio have to be of the same brand?
They don't need to be the same brand, you can install something different, tx port don't even need to be used, then you will set power and channel on the vtx via button but not betaflight
Nice gig 😊
What should I do to be able to use it with a flysky fs-i6 controller?
Congratulations, you just built the original mob7 from 6 years ago👍
Old Mob7 Had F3FC With more grams and less efficient, also harder to PID Tune correctly. Motors fall apart very easy. I had very simillar whoop, then built this beast :)
I don't know about that. The old mob 7 was STUPID heavy. By that logic, all whoops nowadays are just a blade Inductrix with different components. This whoop is crazy cool. 21 grams, in a 75 pro frame. Wild.
@@sakfpv8444no the frame he use is 75mm not 75pro frame it is imposible to get 21 grams on 75pro I have one but the weight is 24 there's nothing you can do to make it 21grams
Hey can someone plz help me, will a flysky fs-i6x work with this? or would i need a different flight controller
Yes you need flysky controller AIO, or can solder flysky nano reciever to existing one
Where to get the camera mount?
It's 3D Printed from rubber, from free thingiverse 3d model
🔥🔥🔥
Super setup, nice flying. Do you mind sharing your tunes and how do you set the launching mode 5:01 , thanks
Motors are discontinued now. What alternative do you reccomend?
Yes, they are discontinued, very unfortunately because old version is more durable than this new shiny edition. But you can still buy them from official BETAFPV store for less money, so hurry up ;)
@@grox3857 No the lower KV variants like you used are already out of strock. There is just 22000KV and 19500KV
@@kratzeni Not good, so we need to use new 0802. Pick similar kv from 10k-16k max for 2s Voltage and also with ball bearings, this is important for high rpm performance. They are more expensive, but no other options on the market right now unfortunately
Thing seems super good, but they don’t make those motors anymore
You can get newer BETAFPV Chrome 0802 instead
Acro mode?
Yup, Acro and same rates as from very beginning like 4 years ago on simulator and fsi6
Can it run normal 2s? Or it has to be 2x1s?
Yes, if you switch to xt30 but this connector is much heavier than 2xbt2.0
What do you think guys, how it compares to the Mobula7 for example, would you choose this custom build or Mob7 instead?
Very nice powerful build! I wish the beta motors had two ball bearings..
@@butterflyfpv But you can get these older updated Beta 0802 motors at very low price from official site. And durability is very very good, still no need to replace them and whoop is operational ater a lot of packs and crashes it has been trough :)
@@grox3857 Ok thank you! I also found 14000kv from neebeedrone..
💪💫
I wonder how it would do on something like a 550mah
Maybe 9mins but it will feel more heavy and not fly as good. I think these 380mah gnb's are close to max weight that fly very well, maybe 400mah for two of these lipos to have 2s max. In bigger lipo you will gain more flighttime but whoop will fly worse and crash harder. It's always a trade one way or another.
how far can it go
Range is pretty baterry limited but 2-5km for the rf links used, and more if you swap better antenas for example foxeer lollipop micro for VTX and Immortal T For the ELRS
What about happymodel se0802 16000kv?
I had them, broke 8pcs in one week so not very durable.
where i can find the stand for whoop in 0:09 second?
Hi, this is my quick project and 3D Printed launchpad
can you please share with launchpad files?
More like 200 bucks
motors 25$ aio 40$ ovx300 15$(now much more expensive hope that they will be more avilable later) Frame 2$ cam 15$ props 3$
But if you have 20$ more I built 5Inch 6s freestyle fpv drone for that money :)