⛐ Check out our Garage to see what tools we use and recommend: www.amazon.com/shop/worldmechanics ⛐ Subscribe and hit the notification bell by the subscribe button for new videos: ruclips.net/channel/UCJ9xpq0qUZevSEdBSFqO2ow ⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys
Great video. My wife hit a pipe on the road with her 2008 Jetta and it popped off the bumper cover behind the tire. I watched this video then went and removed all the connectors on that side and popped out the inner part of the bumper, reattached the cover, and put it back together. She thought she would be without the car for a few days at the body shop and I fixed it in an evening. I would have never found that additional bolt on the other side of the taillight. Thank you for giving the Torx sizes as well.
Thanks for your videos, I recently got an '07 Jetta that had a lot of minor issues(cosmetic). Good strong car though mechanically, I have been fixing and restoring all the neglect including a saggy rear bumper which this video made a breeze. I need to replace a cracked rear tail light next. Thanks again.
Хорошее видео.Все ждал когда ж хоть по русски слова скажет. Акцент выдает )) Лайк. Ждал может с правой стороны покажете после снятия. Мне б увидеть там. А то вчера сдавал задом и не заметил высокий блок. В итоге подмял с права кронштейн крепления бампера и нос выхлопной трубы. И сдвинул выхлопной трубой еще железяку от кузова и в итоге локер задний трется об колесо.Вот думаю как править. Слега оттянул руками но дальше не хватает сил.
I watched this video just to figure out what kind of tool to use to remove the last two screws inside the truck to release the bumper clip...every other screw is called out and shown, except the one I need to see...
⛐ Check out our Garage to see what tools we use and recommend:
www.amazon.com/shop/worldmechanics
⛐ Subscribe and hit the notification bell by the subscribe button for new videos: ruclips.net/channel/UCJ9xpq0qUZevSEdBSFqO2ow
⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys
Great video. My wife hit a pipe on the road with her 2008 Jetta and it popped off the bumper cover behind the tire. I watched this video then went and removed all the connectors on that side and popped out the inner part of the bumper, reattached the cover, and put it back together. She thought she would be without the car for a few days at the body shop and I fixed it in an evening. I would have never found that additional bolt on the other side of the taillight. Thank you for giving the Torx sizes as well.
Muchas gracias por tan buen tutorial, paso a paso, tornillo a tornillo y medida por medida. Un abrazo desde 🇲🇽 God bless U
Nicely done, great detail. Thank you!
Thanks for your videos, I recently got an '07 Jetta that had a lot of minor issues(cosmetic). Good strong car though mechanically, I have been fixing and restoring all the neglect including a saggy rear bumper which this video made a breeze. I need to replace a cracked rear tail light next. Thanks again.
Thanks for the tutorial. I’m having issues trying to slide off the bumper though, it seemingly doesn’t want to budge
Turns out I wasn’t pulling hard enough
Aiight bro nice vid..I'm headed to the junkyard right now to get one off
This video is awesome! After removing the bumper, one piece falls to the ground at minute 10:30. What is it? Looks like a metal bar.
Thanks!
hello hello WM..nics thanks for that video. It helps a lot during work.
Best wishes!
Not bad. These guys discover the bolts as they go. I had the irresistible urge to give them an impact gun but besides that it was okay
Great video guys!!
Great detailed video, thank you !!!
Хорошее видео.Все ждал когда ж хоть по русски слова скажет. Акцент выдает )) Лайк. Ждал может с правой стороны покажете после снятия. Мне б увидеть там. А то вчера сдавал задом и не заметил высокий блок. В итоге подмял с права кронштейн крепления бампера и нос выхлопной трубы. И сдвинул выхлопной трубой еще железяку от кузова и в итоге локер задний трется об колесо.Вот думаю как править. Слега оттянул руками но дальше не хватает сил.
very explanatory. thank you so much!!
благодарю
спасибо за видео
Thanks bro helped out a lot, good video
Could you show how to remove the liners inside rear fenders?
Thank you for great video! Does anyone knows if the rear bumper has inside drilling hole marks for the parking sensors?
what size is the bolt under the carpeted panel?
VER GOOD
How do i take out the spoiler on that car?
Just take off the screws from the top underside of the trunk
great video PLZ shows how to do coolant flush in this model
What a pain in the @ss! Damn vw and 700 different fasteners and tools to remove a damn bumper. Thanks for the video, helps out a lot
I watched this video just to figure out what kind of tool to use to remove the last two screws inside the truck to release the bumper clip...every other screw is called out and shown, except the one I need to see...
It’s the T32
did you grow up in russia with irish parents or vice versa? your accent is awesome
and thanks for the video sir
so many screws lol
My bumper got ripped off and is now missing like most clips how could I replaces those lmao
Buy em online if you haven’t
Overenginering at its finest.
Most fucking idiotic car that I have ever owned. When VW started to assemble them in Mexico, thats when you know VW is not das auto anymore...
But great video guys, thank you!
Can you speak less please….