Thanks sir, this is the difference of good and bad teacher. You solve this dificult issue only four minutes and use least o instruments but rest of the people just perform as a war but we don't understand nothing. I appreciate your teaching quality.
All i need and your clips in practice i learning a lots here you helps me some time on a site i forget or said confused then jump to the lesson of yours and this refreshing my mind Thanks to send me your videos and given me a open refreshing mind mind
لك مني ألف ألف ألف تحية وتقدير على المجهود الرائع يا معلم لا اكدب تعلمة منك الكثير ارفع لك القوبع اسئل الله ان يكرمك بما هو اهله لك ويوفقك الى ما يحب ويرضاه ... امثالك على وجه الارض مثل الاكسير الحياة لا يمكن العيش بلا مصلحين مبدعين في زمن الخراب......ولك شكر الكثير
Since float switch indirectly connects 230v may be thro N however it is unsafe like water tank installation .pl workout lesser 6vDC volt for float connection. It is only suggestion.
@@JrElectricSchoolআসসালামু আলাইকুম স্যার কেমন আছেন আপনি.আমি একটি নতুন শেচ সংযোগ নেব.আমি ৫ এসপি একটি মোটর চালাবো .এবং পল্লী বিদ্যুৎ থেকে কতকিলোওয়াট লোড নিতে হবে.শেচ লাইন আবেদন করতে হবে.জানালে উপকৃত হবো স্যার এবং কত এম্পিয়ারের ডবল.এমসিবি ব্যবহার করতে হবে এবং কত.অ্যাম্পিয়ারের ম্যাগনেটিক কানেক্টর ব্যবহার করতে হবে আশা করি সব কয়টা প্রশ্নের উত্তর দিবেন স্যার
Nice video to understand the basics of wiring a float switch and see how it works. Just in case you may find it intersting, I've got some videos in my channel were I use two float switches to control two water pumps in two different modes: cyclically and by time. Regards.
Very good comprehensive video. I need your guidance. I installed same water flow switch in my undergroud water tank, which is filled with society water. The switch is installes with motor pump to lift water from underground tank to overhead tank. The purpose was that the motor would not empty run if no water in underground water tank. Facing some level problems. Can you guide how to adjust this level in case water is less in underground tank the motor would be off.
So with the contactor you avoid pulling full current of pump thru the float switch in the tank, but you still have the issue of 220V going into the tank thru the float cable. Does it really make that much of a difference in safety to have a contactor in that case? I guess if your float switch isn't rated for the pump current?...
Hi. I used to do like this but later I discovered it's a bad practice installation. Contactor of 24V coil should be preferred, and that coil closes the 110V or 220V supply. You only need to add a 24 DIN rail supply or using a 60W, 220V-24V transformer. There is also the option of getting a 12V relay do accomplish it, but it looks less professional and somehow it is more risky.
@@JrElectricSchool sir agr submersible pump ko tank bharne ke bad auto band ho jaye tank Khali hone par auto start nhi karna hai to sir kaise lagaen ya uske liye koi asemi auto nam ka product aya hai please reply me
@jr electrical school Can you tell me what changes I should make in wiring so that my motor turns off when water level is low and turns on when water level is above set low level in float switch. This is for a .5hp pressure booster pump on I’ve put on the terrace
I watch your video and download it. Its very very nice and helpful. I have a single phase 2hp electric motor water pump. I want to install a floater switch but only 10 amp is available in the market. Can i use it using a magnetic contactor? What is the specifications of contactor should i buy? Thanks for replying.
Your video is really appreciated but I find a mistake in the connection. Plz you are connecting a floating switch so NO should be connected in phase wire rather than neutral. Never mind
This simple circuit is controlling the load indirectly by the float switch: the float switch is energizing the contactor relay coil, which commutes its contacts and energizes de load. Simply, the electric contacts of the float switch are not designed to control the load.
Thank you for sharing this . Anyone correct me if I am wrong. isn't this bad design in terms of safety?!. At the end the floating switch has a lifetime and at one moment the water will find its way to the current which will expose the high current to whole water risking lives to anyone in contact with that water. To reduce the risk the floating switch should have earth wire which will trigger the main switch when current leakage. Another way to terminate the risk is by using the floating switch as low current switch 5-12 v connected in some way to control high current relay.
si puedes, pero se te quemaran muy rapido los flotadores, el Contactor es por la corriente inicial es alta y este evita que los flotadores se encarguen de eso.
Thanks sir, this is the difference of good and bad teacher. You solve this dificult issue only four minutes and use least o instruments but rest of the people just perform as a war but we don't understand nothing. I appreciate your teaching quality.
All i need and your clips in practice i learning a lots here you helps me some time on a site i forget or said confused then jump to the lesson of yours and this refreshing my mind
Thanks to send me your videos and given me a open refreshing mind
mind
Glad to hear it!
لك مني ألف ألف ألف تحية وتقدير على المجهود الرائع يا معلم لا اكدب تعلمة منك الكثير ارفع لك القوبع اسئل الله ان يكرمك بما هو اهله لك ويوفقك الى ما يحب ويرضاه ... امثالك على وجه الارض مثل الاكسير الحياة لا يمكن العيش بلا مصلحين مبدعين في زمن الخراب......ولك شكر الكثير
Instead of 220 volts for float switch i think it should be 6 volts for safety. Nice video thanks .
Since float switch indirectly connects 230v may be thro N however it is unsafe like water tank installation .pl workout lesser 6vDC volt for float connection. It is only suggestion.
Bahut hi shandaar. Aapne bahut hi aache tarike se samjhaya hai. 🙏
ভাই আপনার ভিডিও টা অনেক বেশি ভালো লাগলো,,,, সহজেই যে কেউই বুঝতে পারবে।আপনাকে জানাই অসংখ্য ধন্যবাদ।
Thank sir humne try kiya 100% real 👍
আলহামদুলিল্লাহ
ভাই কাজ চমৎকার করতে পারছি.....
Thank u brother.
Good and small sweet work
From sri lanka North
Thanks and welcome
@@JrElectricSchoolআসসালামু আলাইকুম স্যার কেমন আছেন আপনি.আমি একটি নতুন শেচ সংযোগ নেব.আমি ৫ এসপি একটি মোটর চালাবো .এবং পল্লী বিদ্যুৎ থেকে কতকিলোওয়াট লোড নিতে হবে.শেচ লাইন আবেদন করতে হবে.জানালে উপকৃত হবো স্যার
এবং কত এম্পিয়ারের ডবল.এমসিবি ব্যবহার করতে হবে
এবং কত.অ্যাম্পিয়ারের ম্যাগনেটিক কানেক্টর ব্যবহার করতে হবে
আশা করি সব কয়টা প্রশ্নের উত্তর দিবেন স্যার
Nice video to understand the basics of wiring a float switch and see how it works. Just in case you may find it intersting, I've got some videos in my channel were I use two float switches to control two water pumps in two different modes: cyclically and by time. Regards.
IT'S WONDERFUL ....
I watch your video and download it. Its very very nice and helpful.
Many many thanks
Simple and suitable for beginner in this field..recommended for reference.nice bos!
Not suitable for beginners. 240v ain't good for beginners
your all videos is the great my favourite. thinks breather.
Thank you very much!
This is very educative, thanks for sharing it with us...
Thanks sir your method is very simple & fantastic
Most welcome
Bahtaran Bayi video siav nahe hotel 👉😌
i will try to make video on your topic.
Thank you.
Very good comprehensive video. I need your guidance. I installed same water flow switch in my undergroud water tank, which is filled with society water. The switch is installes with motor pump to lift water from underground tank to overhead tank. The purpose was that the motor would not empty run if no water in underground water tank. Facing some level problems. Can you guide how to adjust this level in case water is less in underground tank the motor would be off.
Brother very useful 💡 ideas giving u... Well..
Please keep upload every days videos... Thanks.
i will try my best
Thank you so much!
FC ex FC FC
So with the contactor you avoid pulling full current of pump thru the float switch in the tank, but you still have the issue of 220V going into the tank thru the float cable. Does it really make that much of a difference in safety to have a contactor in that case? I guess if your float switch isn't rated for the pump current?...
This is a normally closed float level switch, which means the common contact is connected to NC contact when float is in down position
Thanks for the video. It really good please next text try to explain your step .keep up.
i will try
Thank you so much!
Thanks a lot for your video,It means when you set the model of the lamp it should be the pump motor
Yes, thanks for watching
ভিডিওটা দেখে অনেক ভাল লাগছে
Thank you very much!
Hi. I used to do like this but later I discovered it's a bad practice installation. Contactor of 24V coil should be preferred, and that coil closes the 110V or 220V supply. You only need to add a 24 DIN rail supply or using a 60W, 220V-24V transformer. There is also the option of getting a 12V relay do accomplish it, but it looks less professional and somehow it is more risky.
Your video is amazing dear sir G
Thank you so much
Thanks for share your videos really your videos is amazing for electrical learning 😍
It's my pleasure
Best
@@JrElectricSchool sir agr submersible pump ko tank bharne ke bad auto band ho jaye tank Khali hone par auto start nhi karna hai to sir kaise lagaen ya uske liye koi asemi auto nam ka product aya hai please reply me
Thank you sir. How about wiring two float switches to two tanks ( up and down) without the use of a contactor.
Thank you sir nice information ☺️
Welcome
😮lack of explanation sir..
Nice video 1👍👍👍👍
Hello sir thanks for your video but sir please talk while Explaining .....because I don't know how to connect contactor sir
Thank you so much for share your opinion i will try
you please watching this video ruclips.net/video/NCc9V3z32jY/видео.html
@@JrElectricSchool व्हीप 😆😆😆😆😆😆😇😇🥰🤣
@@JrElectricSchool nnjjmlkllllkllklkkkoiio
لثنامؤزغى
@@abccreation6212 قنفاحبظىظازهبنةيجتةيتظىجت
Thank you very much for this important video.
nice video vai...
Thank you very much
cool song
Simple and great explain.
Very Very good again good 👍 👏 👌
Very educative thanks for sharing it with us
At last...it was your video that did it for me...Thank you
Thanks for sharing your knowledge to use
you welcome
Superb work
Thanks a lot 😊
Nice video
Thank you so much
@@JrElectricSchool ijvubjhhkjjkkoiiuhi
Good videos for electrician
Thanks 👍
Thank you for sharing your video s
You are so welcome!
Wery good bos im sri lanka you from ❤️❤️
Thank you so much!
God Bless you❤️❤️
Thank you very much!
vvv
vvv
vvv
vvv
Very very useful 👍
Thanks a lot
Nice....maybe next time pressure switch
i will try
Thank you
(kkkl@@JrElectricSchoolde kkkkkkkkk(com.google.android.gms com.google.android.gms en un mundo nuevo de nuevo disco
@@JrElectricSchool ggggggggggggggggggggggg
@@JrElectricSchool gggggggggggggggggggggggggggg
@@JrElectricSchool gggggggggggggggggggggggggggggggggggggggggggggggggggggg
Gggg
Ggggggggg
Good job its helpful for me
Thanks
It's my pleasure
Excellent work Bro
Thank you so much 😀
Thanks to the video tuturial you shared.
You are welcome
Nice sir ----------------------
Thanks
I fully sport u,
Thank you very much!
Very nice system .Please explain by diagram .please............
Very nice 👌 👍
@jr electrical school Can you tell me what changes I should make in wiring so that my motor turns off when water level is low and turns on when water level is above set low level in float switch. This is for a .5hp pressure booster pump on I’ve put on the terrace
Would you please tell me that what’s the benefit of using a Connector and what’s its role. Thanks
I watch your video and download it. Its very very nice and helpful.
I have a single phase 2hp electric motor water pump. I want to install a floater switch but only 10 amp is available in the market. Can i use it using a magnetic contactor? What is the specifications of contactor should i buy? Thanks for replying.
you can use magnetic contactor for float switch
In short did you use the float switch as a loop or??
Your video is really appreciated but I find a mistake in the connection. Plz you are connecting a floating switch so NO should be connected in phase wire rather than neutral. Never mind
Thank you sir, i finally made it
220v water tank me kya daalna sahi hoga? Ya iski jagah kuch or bhi kiya jaa sakta hai? Pls make the video
Cristal clear explanation
Very helpful video, thanks for sharing
Good job sir
Good job
Thanks
do i need auto controller for motor or this connection will do the work?
V good work
Thank you so much 😀
Can we use over lourd relay as a single phase
It is safe to use? 220ac Volts
Nice Work
Thanks
why did u put flot switch in neutral...keep in phase is good practice.
Wow good job sir can i ask sir what is the number of contactor you use
Nice job thanks
Thanks for watching!
For 3 phase motor ?
Why do you use another switch in between float switch and load?
This simple circuit is controlling the load indirectly by the float switch: the float switch is energizing the contactor relay coil, which commutes its contacts and energizes de load. Simply, the electric contacts of the float switch are not designed to control the load.
Nice Bhai
Thank you so much
Sir water over flow
Ka switch chalaye apni marzi sy aour off automatic ho jaye jub pani ki tanki full ho jaye wo bi batain ke kaisy banain
i will try to make video on your topic.
Thank you
@@JrElectricSchool thank's
@@JrElectricSchool semi autometic water overflow switch
Nice work
Thanks for the visit
Thank you for sharing this . Anyone correct me if I am wrong. isn't this bad design in terms of safety?!. At the end the floating switch has a lifetime and at one moment the water will find its way to the current which will expose the high current to whole water risking lives to anyone in contact with that water. To reduce the risk the floating switch should have earth wire which will trigger the main switch when current leakage. Another way to terminate the risk is by using the floating switch as low current switch 5-12 v connected in some way to control high current relay.
This is for a 220V installation right? red and black are both lines?
Nice vídeo ive the some thing in home thanks!
Thanks for watching!
@@JrElectricSchool òoòoòòòoooò9988ò9oòòòòò999òò9ò9òòò9999oò9òòò9òòo9oò999oòo99ò9999o999o99o9o99o9o99oo99999o9ooo9ooo99ooo9oo99oò99ò99ooooò9o9999ooo9oo9o99òoò99oòoo9ooo9999òò99o9o9oo9òo9978888888888888888ìiiìììiiìììiìììiììiììììiìiìiìììiììììììììiììiììiiììiiììììiìììììiiììììììiììiiììììììììiììiìiiìiììììììiììììììiìiiììiìììiìiiiiììiììììiìiìiiììiiiiiiììiiìiìiìiiiiììììiìiiiiìiiiiiiìiiiiìiiiìiiììiìiiiiiiiiìiìiiìiiiììiìiìiiììiiiiiiìììiìiììiiììiiiiiiiìììiiiiiììììiiiiììiìiìiììììiìiìììiììiìiiiiìììiìììììiìììiìììììììììiiiìiìììììiìì
Thanks bro👌🏾
you welcome
Thank you so much 🥰
You’re welcome 😊
@@JrElectricSchool thank you teacher 🥰
@@Somali122 it's my pleasure
So what’s the name of those breakers?
Deeply soche to ye bahut dangerous ho skta hai kyoki float switch me 240 volt rahega jo f
Kharab hone pr current pani me bhi aa skta hai
Thanks for share your your opinion
nice vai
Connect neutral directly to contacter not a phase
Good job🥰
Thank you 😋
Welcome 😊😊
Very good indeed
Thank you very much!
Idea is good but AC current +Water =⚡
Thanks for share your opinion
Flote is sealed not shock
Nice one
Good videos
Thank you very much!
nice, but next time wire it correctly. Line on top of breaker and load on buttom
Thanks for the tip
Wonderful video. How to wire 2 float switches, one for underground water tank and one for overhead tank?
Solo conecte los flotadores en serie, claro, revisando que una en posicion elevada se active y la otra en pocision baja se active.
hello...how to reverse it?? my purpose is to prevent the pump from continious operation if the water lvl is low in the tank?
Good 👍
बिना मॅग्नेटिक कंडक्टर युज किये फ्लोट स्विच मोटर के साथ फिट कर सकते है क्या.
मेरा एक इंची का एक एचपी सिंगल फेज मोटर है.
Can u plz add a selector switch to bypass auto and manual. Plz make video
hello guys hope you answer my question. I just want to know if i can use this without the contactor.? Can I go directly to breaker?
si puedes, pero se te quemaran muy rapido los flotadores, el Contactor es por la corriente inicial es alta y este evita que los flotadores se encarguen de eso.
Sir ye kis kam ke liye use hota hai float switch
automatic water pump on off
@@JrElectricSchool ok thnx
@@coldroomsourabhcoldroomsou6014 you welcome