You don’t need the start, stop push button switch. The HOA switch will do the job starting and stopping the motor. A good circuit design is one that will do the job safely with less parts.
If the main power supply is on and if the gen set transfer the load back to the main supply and if the gen set dosent shut down, where can we troubleshoot and identify the fault?
This circuit not recommended for safety reason, The control supply must be 12v or 24v only recommended. Safety is first , nothing is more important than the safety .
What is the use of this single wire float in the tank. Je ne comprends pas le rôle de ce flotteur à un fil. C'est joli mais flou. Les boutons rouge NC ou vert NO sont des poussoirs, alors I have not understood.
Better to place some delay timer because floatswicth are not steady with the flowing of water inside the tank and may casuse yong contactor ang motor damages and i experience it...
If power supply is off, and if the gen set is on and transfer the load and then the main power supply comes back on and the gen set continue to run with out transfer load. What is the fault and where can l troubleshoot?
In my opinion, if I use the m version, the scheme does not work because in the absence of water you will burn the motor also because you do not even have an electric absorption control
Los cables con tensión entran siempre por arriba. No hay protección en dicho plano que hiciste.. Tenes que saber que los comando se maniobran con 24v/a en tanque. Circuito de fuerza motriz y circuito de comando. La conexión esta mal
Hey Soozler! I had this same issue. I'm guessing his coil is 220V. You only want 120 V going through the coil. The basic idea is that you only want one side of the coil getting power (left side in this case, via the jumper) and your black float switch wire should be connected to your neutral wire, and the other wire from the switch connected to the right side of the coil. I can send you a diagram if you want.
This is a poor design, the float switch is not in the circuit in the automatic mode, this could be catastrophic depending on the process it is used for
If power supply is off, and if the gen set is on and transfer the load and then the main power supply comes back on and the gen set continue to run with out transfer load. What is the fault and where can l troubleshoot?
Vraiment c'est très passionnant et un grand merci pour votre collaboration cordialement... Merci infiniment
Very nice Video Very Good Information Sir .❤
Thank you very much!
Nice video vai.
Thank you very much
Thanks for sharing this with us.
Bhut hi achha hai video sir..but sir ek request hai wiring diagram k sath batayenge humlogo k bhut hi achha rahega
i will try
Thank you
Muy agradecido amigo que Dios te bendiga
If standard numbers are used for the terminals to be connected, it can be clearly learned ... just like the contactor ...
Thank you very much for share your opinion!
You don’t need the start, stop push button switch. The HOA switch will do the job starting and stopping the motor.
A good circuit design is one that will do the job safely with less parts.
If the main power supply is on and if the gen set transfer the load back to the main supply and if the gen set dosent shut down, where can we troubleshoot and identify the fault?
nice video
Thanks
If I'm using a pilot light toggle switch for manual, instead of the stop/ start buttons, how do I wire it?
Can you tell me the type of contactor you want to buy ...? Please ... Thank you ...
Very nice video
Thanks for watching
ruclips.net/video/8BYGt7Nah1c/видео.html👈
مشكورين على المعلومات الى الامام انشالله
sorry i am not understand your language
please tell Bangla Hindi English.
Thank you
Thank you👍🙂 my water pump is 0.7kW. Which choise contactor?
Sir, can you please share the specs of the control devices? thanks
This circuit not recommended for safety reason, The control supply must be 12v or 24v only recommended. Safety is first , nothing is more important than the safety .
Thank you so much for share your opinion
Super brother
What are reason we are using red and green button pls explain and y didn't give netural for green and red button
what is your constraints on this project?
What is the use of this single wire float in the tank.
Je ne comprends pas le rôle de ce flotteur à un fil. C'est joli mais flou. Les boutons rouge NC ou vert NO sont des poussoirs, alors I have not understood.
Hi
What program did you use to build this?
I need it for my dissertation.
Thanks for the reply
Better to place some delay timer because floatswicth are not steady with the flowing of water inside the tank and may casuse yong contactor ang motor damages and i experience it...
Sir do you have any video using two float swit for water pump
no but i will try to make video on your topic.
Thank you.
Super bro
Thanks
If power supply is off, and if the gen set is on and transfer the load and then the main power supply comes back on and the gen set continue to run with out transfer load. What is the fault and where can l troubleshoot?
In my opinion, if I use the m version, the scheme does not work because in the absence of water you will burn the motor also because you do not even have an electric absorption control
If I was wrong please tell me why
your feedback is very important for me
Thank you so much for share your opinion
That means the MCB there is useless if the motor could beburnt
Los cables con tensión entran siempre por arriba. No hay protección en dicho plano que hiciste.. Tenes que saber que los comando se maniobran con 24v/a en tanque. Circuito de fuerza motriz y circuito de comando. La conexión esta mal
Interesant Întotdeauna avem de învățat
Can you do wiring in manually
i will try to make video on your topic.
Thank you.
Ok felicitări
My friend please try to make video without music 😭 Thanks.
Thank you so much share your opinion i will try
@@JrElectricSchool "You are Most welcome My Dears 🌷
@@azizulhaque5040 my pleasure
Nice
Thank you so much
Questions? PO what is the use of E? Nd? PO naka connect? Pasenxia na po sa tanong!!✌️✌️✌️
I want the picture of single pole mcb and with out indicator
Thanks
Welcome
Hey Soozler! I had this same issue. I'm guessing his coil is 220V. You only want 120 V going through the coil. The basic idea is that you only want one side of the coil getting power (left side in this case, via the jumper) and your black float switch wire should be connected to your neutral wire, and the other wire from the switch connected to the right side of the coil. I can send you a diagram if you want.
What model magnetic contactor thanks.
schneider magnetic contactor
Why no use overload contactor no protection motor..
it is single phase motor no need overload but you can use for your protection no problem. Thank you
Svp quel est le nom du logiciel que vous utiliser pour faire votre dessin ?
sorry i am not understand your language please tell me Bangla,Hindi,English.
Thank you.
Please name the circuit diagram program
animation
Submersible ka canection kar na hoga to kiya kar na hoga 1 phase canection Submersible
NICE
Thanks
when auto system is running, line signal is reverse to Manual point
deberian poner la numeracion del contactor asi como su bobina
nice
Thanks
Konsa part kya work karta hai, uska kya effect hota hai,,,,,ye kon batayega
ape internet me search ke jeya ape ko pata chalgaye ge
Still i can't able to understand Auto and manual concept....Pls explain anyone
your water pump run automatic
@@JrElectricSchool ok..But the wiring concept is not understand...Explain it
Motor Panel ryb kya conction
RYB is 3 phase line
প্রতিটি পয়েন্ট এর নাম উল্লেখ্য করে দিলে যারা জানেনা তারা শিখতে পারত। আপনার উদ্দেশ্য তো শিখানো তাইনা?
No back round music pl sir
Thank you so much for share your opinion
i will try
Solar system to bettry charge diagram drowning and use bettry home components
i will try to make video on your topic
Thank you
ruclips.net/video/8BYGt7Nah1c/видео.html👈
Tengo una bomba sumergible y tengo que controlar dos o más cisternas con eletronives
sorry i am not understand your language
please tell Bangla Hindi English.
Thank you
Send me a photo wiring for inveter
i will try
Stop bottom to contactor no why need connection
holding connection
ruclips.net/video/8BYGt7Nah1c/видео.html👈
tres bien
Très bien
This is a poor design, the float switch is not in the circuit in the automatic mode, this could be catastrophic depending on the process it is used for
Chévere
5 मंजिल से मोटर चलना चाहिए
ruclips.net/video/8BYGt7Nah1c/видео.html👈
Sir kama shikhana ha Bhai
ko e problem ne he ape youtube se seksakte he free
@@JrElectricSchool Kon school ke sir electric he
Admission sir karana ha
@@vikashnirmalofficial8206 ape internet me search ke jeya
ruclips.net/video/8BYGt7Nah1c/видео.html👈
ভাইয়া আপনি কি সফটওয়্যার ব্যবহার করেন দয়া করে একটু লিংকটা দিবেন আমাকে।
i am so sorry for youtube community guidelines
I used PowerPoint 2019 animation
best of luck
e' incompressibile,,,,,si deve prima fare lo schema elettico, manca lo stoz degli ausiliari.....
Weher the over load.
it is single phase motor no need overload
but you can use no problem
[power electric motor]]
yes!
Thanks for watching
Lain kali di buat kode NC & NO nya
Waring rong
L rong hai
why?
@@JrElectricSchool manual to 14? which will trigger the coil a1 and a2 in manual?
Ra mya
Complicated
If power supply is off, and if the gen set is on and transfer the load and then the main power supply comes back on and the gen set continue to run with out transfer load. What is the fault and where can l troubleshoot?
Nice
Thanks for watching