For Using multi Protocol Radiomaster radios that have E129 and sub protocol C186. Not supported by Atmega328p modules. you can use the following channel assignment CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 A E T R Take off/Land Emergency Trim A Trim E Trim R Trims can be done to some extent on the AETR channels directly but if you push them too far you won't be able to arm like explained below. In this case use the associated trim Trim A/E/R instead. Take off with a none spring throttle is easier by putting both sticks down outwards (like on the original radio) in Mode 1/2, not sure about other modes. Calibration is the same as the original radio with both sticks down and to the left in Mode 1/2, not sure about other modes.
Please tell us if you do bind it to a Radiomaster TX. Will be interesting to know if it can be adjusted to fly with increased bank angle or the altitude hold turned off.
@alishanmao was looking at getting a TX16s to fly this. Which one should I get to bind directly to this helicopter? Want to make sure I get the one that will have the correct protocol to bind to this. Appreciate any help you can give👍🏼
This is a very nice looking and detailed scale model of the MD500! For sure it might bring some new pilots into our hobby. And who knows, one day they might do the next step to fly 6 channel collective pitch helis and build their bigger HD 500 scale heli with a nice 400 or 450 mechanic inside! Very complete review!
Favorite all time copter finally they get it, make affordable rc copters with accurate scale looks, can't fail, sell a pnp version too, even better. Let's hope the trend continues. BTW, if never heard of it check out an old movie from the 70's or 80's call Bird of Prey or Birds Of Prey. It has lots of great flying scenes with Hughes 500 and Lama helicopters, another favorite.
It's about time they realized the demand for affordable RC copters with accurate scale looks. Now we can all feel like expert pilots without breaking the bank. Who knows, maybe we'll even see a James Bond-inspired version soon!
Thank you for your review. This heli, C189 MD500, what I'm looking for that 4CH scale heli with main and tail brushless motors. I've ordered same military model as yours, and I'm very exciting to get this soon. :) Additionally, I'm wondering I can use my Futaba T14SG transmitter for this.
i do not think you can use other radios, except that someone said maybe boxer and tx16s multiprotocol radios that have E129 Sub C186 protocols maybe able to bind
This heli can be used with the Radiomaster TX16 using EdgedTX and the C186 sub protocol. Your videos on the TX16 are very good and even more valuable since you're using it with many helicopters. Please consider making a video about how to program the TX16 to use with the C189, and also the C186 if you could.
Nice looking heli. Does it come with any spare parts? Are spares available where you buy it? Does it have 2 or 3 servos on th cyclic? Could you possibly swap out the Rx for a Futaba or Spektrum and bund it to a better radio? Thanks
I have bound my MD500 CG Version With Flow Control to my new TX16S. Flown it 4-5 times in my Hanger/Garage. 🤠 Still fine tuning Rates and Expo. It’s a little too Jerky even so. Do you think Gyro Gains (CH 5?) be turned down on the Head and Tail with added Inputs settings?
do you need to use the auto take off ?I seen a video were the auto take off went out of contorl.they lost it by hitting the stop button. they could of waited the 17mins for the battery to go down . then it would of soft landed.
Hi I was wondering if you could help me with my one i did everything the manual said and I did the ato take off and it just flies away so I did the ato stop and I did it all over and it still flies away so can you please tell what is wrong with it please.
Nice Ali. Hoping you would be doing a review on this soon. Shame optical flow was left out. I would imagine they will add optical flow on the next version of it. 🤠
As for finding protocol for Tx16s. I know it is a lot of work, you could just try to bind to each one until you find the one that works. A lot of work I know, but possible
@@aureliusprimus I just received it but as we are leaving China and moving to another country, today I shipped the AS350 to Shipper and it will be on the ship to our new destination. probably i can post a video from a new place where we will move after I receive it after a month or more. so you gotta wait. no choice. right now i can't do anymore videos. I just have videos scheduled till 3rd November. 2nd november we will fly out. all our luggage is gone, rest is packed and we are just waiting.
@@alishanmao I understand my friend. Do you like going to another country or were you forced to leave China? You don't know which country will welcome you? Frankly, you should come to France, you would no longer have any moving worries ! 😀
So I finally made mine a "6ch" heli but I changed the esc to with the blade apache esc. Which I have a spare of. (You don't have to do this if you can find the signal pin for tail and main on the original esc, i just don't have enough time) and for the flight controller I used my spare Trex 150. Now you cannot get usable negative pitch because there's just no room for the swash to go down, but fine by me, it's a scale heli. But what I'm left with is an md500 that can easily do realistic maneuvers, because it doesn't have self leveling. Now the easiest way to do this is literally put the omp m2 flight controller and esc. And one last important thing is make sure you don't have negative pitch curve, because the swash plate doesn't have enough space to go down. As for battery, I went with the original for now all because of simplicity and I have 3 already. Once the battery is done I'll change the plug to xt30
One of the reasons why i changed the flight controller, is that this heli actually is bad flying backwards. You could try it. If you fly backwards, the heli will try to pitch forward again. And it's annoying because when you are trying to even just hover, if you correct the heli to pitch back, it will pitch forward. It likes forward flight. But for some reason, the flight controller gets confused when I fly backwards.
I got the answer from a RUclipsr. I finally found how to switch the transmitter to mode 1! You must push the mode 2 throttle trim up and hold it in this position while turning on the transmitter. then we release the trim button and push the right stick to the high position then to the low position. and the transmitter is in mode 1 and it will remain so each time it is switched on. To return to mode 2, it's the same operation except that you activate mode 2 by pushing the left stick to the high position, then to the low position. @@alishanmao
Many guys have a "fly away" is there any fix solution? Mine fly 5 times fantastic but at 6 of auto start its fly away impossibel too hold with sticks down or up !Luckily it hits a big tree!
I have just Isolated the Control Boards Stack off the Frame with double sided 3M Foam Tape to lower Vibrations getting to Gyros. It helped smooth it out by 25-30%? Flys a little Smoother indoors. 😊
The original design of this helicopter aka "Little Bird" was made for the CIA and special forces by Hughes Aircraft of Howard Hughes fame. Bell helicopter merged with Hughes in the 1980s but the original design of the little bird has not changed beyond improved turboshaft motors
The OH-6 was initially made as a light observation helicopter to scout for troop carrying Huey’s and attack aircraft. The CIA did use a Modified OH-6 with a muffler type design on the exhaust nozzle to suppress the noise and added a 4 bladed tail rotor and a 5 bladed main rotor and named it “the quiet one”. Hughes Aircraft Merged with McDonald Douglas not Bell in the 1980s. HUGHES aircraft designed and produced the OH-6 loach and then the HUGHES 500 - the civil model. Hughes aircraft also designed and built the AH-64 Apache in 1997 MD merged with Boeing which kept the rights to the OH-6 and AH-6 Littlebird and of course the Apache. MD helicopter became its own thing and kept continued to make new models of the Original Hughes 500. Boeings version of the MD500, the OH-6X is more powerful and more sophisticated than the current MD500 with a 6 bladed main rotor and 4 bladed tail rotor and it’s even capable to fly unmanned and can be controlled by the front seater of the AH-64E Guardian.
I saw another review on this bird. It too did not have the optical flow even though in the web description it states that it has optical flow. So WTF is up with that???
i believe the samples sent to Reviewers like I got one and i believe captain drone did a review of it before mine. those samples for reviewers do not have optical flow but mass produced ones may have it. anyway i like it without optical flow
Wish mine would fly like this one😢. Mine would just spins up a little before cutting off by itself. No idea how to fix it so it now just sits on the shelf.
Don’t know why, but mine will Back up at a 45 deg. angle and go quickly Right When I input Left AIL. 20-25% Expo. Going to Reduce Expo further because if I push past Expo quickly I can Catch the abnormal right/rear shooting off and go Left and forward like I want it to do. So thinking reduce Expo further and maybe the Control will Catch that un commanded movement quicker. More precision….? Who knows. Trying to eliminate that strange opposite movement. A little Risky in a 12 ft square area with walls. 😮
IDK IM HAVING THE WORST OF LUCK WITH THESE HELICOPTERS I JUST GOT A MD500 & NOW IT DOESN'T WORK I TURN IT ON ALL IT DOES IS BEEP NO LIGHT FUNCTIONS ARE ANYTHING IT'S DEAD IDK WTF HAPPENED THIS THE 2ND HELICOPTER GIVE ME PROBLEMS F06 EC135 WENT INTO MODE 1 COULDN'T GET IT FIGURE OUT TILL IT WAS TO LATE & NOW I HAVE PROBLEMS WITH THIS MD500 VERRY FCKN FRUSTRATING & ALL I WANNA DO IS BE ABLE TO ENJOY IT I WANT ANOTHER ONE BUT I DON'T KNOW IF I CAN TRUST THESE HELICOPTERS NO I ONLY FLY SCALE
i believe these companies really need to step up on quality control and customer support, or else they will die soon if they keep on doing sell and forget attitude
Do not purchase through makerfire... I bought one and it was defective and contacted the company about a replacement as soon as it came down to replacement they stopped responding to my emails.. sent them videos pictures etc... And no response.. stay away from the company makerfire..
Sorry to hear that, i know Jack Xie, a good friend. i will send him message with your comment screen shot. they should not treat customers this way. I advise buying from bit.ly/48l8jhs they are very reliable and i am in touch with them on daily basis. Ben is very responsible and supporting too.
Hello, this is Jack from Makerfire. First and foremost, I want to extend our sincere apologies for the inconvenience you've experienced. We understand how frustrating this situation can be and take your feedback very seriously. I have reviewed your case with our customer service team. According to our records, you reported an issue with the tail light not working on your RC helicopter. We responded to you on November 6th, requesting a video to demonstrate the problem. We are still awaiting your response. To expedite the resolution of your issue, please contact our customer service team directly and supply the requested video. We are committed to addressing your concern promptly and ensuring your satisfaction. Again, we apologize for the inconvenience you have encountered and look forward to your response so we can resolve this issue swiftly. Sincerely, Jack Makerfire Team
I pay for RUclips I don't need to pay for an individual channels once in a while contributions that's greed and it cost u your subscriber thanks for forcing me to figure it out on my own I'm gonna make my own video and I won't charge for it. Hope u make a lot of money because you're gonna lose a lot of subscribers Real RUclips big dogs don't need to charge for membership you should've done it the way you were doing it before. Good luck I won't be back
if it disappoints you, everyday I am getting new supporting and understanding subscribers. does that make you feel bad that i am still getting subscribers while you have to leave because you do not want to show any understanding to someone who is trying to make his rightful living with his content that takes lots of efforts, time and our own money to bring this content? Shouldn't you stop charging for whatever work you do, because its greed. you should do it for free too don't you think? because if you get salary then you are greedy too. if you are taking salary and getting paid for what you do and you call me greedy, its called hypocricy. Good luck, and welcome back to my channel any time you want.
@@alishanmao I'd never unsubscribe, you're my favorite RC reviewer. But my wife does not like me watching your videos because it ends up in new toys! LOL
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
For Using multi Protocol Radiomaster radios that have E129 and sub protocol C186. Not supported by Atmega328p modules.
you can use the following channel assignment
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9
A E T R Take off/Land Emergency Trim A Trim E Trim R
Trims can be done to some extent on the AETR channels directly but if you push them too far you won't be able to arm like explained below. In this case use the associated trim Trim A/E/R instead.
Take off with a none spring throttle is easier by putting both sticks down outwards (like on the original radio) in Mode 1/2, not sure about other modes.
Calibration is the same as the original radio with both sticks down and to the left in Mode 1/2, not sure about other modes.
Please tell us if you do bind it to a Radiomaster TX. Will be interesting to know if it can be adjusted to fly with increased bank angle or the altitude hold turned off.
Would this also work with RadioLink AT10? the supplied radio is very very basic
@alishanmao was looking at getting a TX16s to fly this. Which one should I get to bind directly to this helicopter? Want to make sure I get the one that will have the correct protocol to bind to this. Appreciate any help you can give👍🏼
This is a very nice looking and detailed scale model of the MD500! For sure it might bring some new pilots into our hobby. And who knows, one day they might do the next step to fly 6 channel collective pitch helis and build their bigger HD 500 scale heli with a nice 400 or 450 mechanic inside! Very complete review!
Couldn't agree more!
@@alishanmao Ok I figured it out i got my C189 MD500 working now the optical plug was in the wrong post
Sounds, and looks like great value. Very nice flying, as always.
Thanks again!
The hugest 500 is in my opinion one of the sexiest helicopters ever made
it sure is
Thanks! I have been waiting for this review for few weeks!
Hope you like it!
i ordered one of this and its coming very soon. im so excited. thanks for the very nice review bro.
Hope you enjoy it!
Favorite all time copter finally they get it, make affordable rc copters with accurate scale looks, can't fail, sell a pnp version too, even better. Let's hope the trend continues. BTW, if never heard of it check out an old movie from the 70's or 80's call Bird of Prey or Birds Of Prey. It has lots of great flying scenes with Hughes 500 and Lama helicopters, another favorite.
It's about time they realized the demand for affordable RC copters with accurate scale looks. Now we can all feel like expert pilots without breaking the bank. Who knows, maybe we'll even see a James Bond-inspired version soon!
Definitely a great looking copter! The performance is amazing!!! How long is the battery time on this?! Keep up the great work! ✌🏾
they advertised 17 minutes. i guess its right. i flew it for over 15 minutes no issues
Wonder if swaping in a goosky s2 reciever would work to get 6ch and not auto level 🤔
you mean the autopilot
So it can fly line a "real" heli. Like 3d mode
Compared to the F06 EC135, which one is better to fly and easier to control? Thank you very much. 😊
this one feels and flies better. always welcome
I take the white red one because finding it more easy after crash in the forest ha ha!Looks like a new level of "scale beginner Helis"!
well i love the looks on military one. still there are other variants, hope they will make more military ones soon
I have read the optical sensor will be optional. Maybe there will be an additional modell soon.
possibly
Finally! An md500 with 5 blades!
Id put a different flight controller on that immediately and make it 6 channel
hope that works out
I have a boxer transmitter and it only came with e129 protocol. I got the local drone shop to download sub protocol c186 from open companion
hmm so C186 protocol works on this heli? what are the channel assignments? guess Ch5 for flight modes and rest is simple plane setup?
@@alishanmao I don't have my rc era c189 yet but 3 previous rc era helicopters that I have binded to this protocol so I'm hoping it will.
Would you be able to bind it to your boxer transmitter to see if it works and do a tutorial on setup on the boxer?
Thank you for your review.
This heli, C189 MD500, what I'm looking for that 4CH scale heli with main and tail brushless motors.
I've ordered same military model as yours, and I'm very exciting to get this soon. :)
Additionally, I'm wondering I can use my Futaba T14SG transmitter for this.
i do not think you can use other radios, except that someone said maybe boxer and tx16s multiprotocol radios that have E129 Sub C186 protocols maybe able to bind
This heli can be used with the Radiomaster TX16 using EdgedTX and the C186 sub protocol. Your videos on the TX16 are very good and even more valuable since you're using it with many helicopters. Please consider making a video about how to program the TX16 to use with the C189, and also the C186 if you could.
Thanks for the info! I will try. at the moment am too busy with so much to do for our move in UAE. step by step all will be done.
Would also like to see this please!!
Nice Heli, after 17 mins of fly, can I just leave the batter as it or do I need to do some charge back for batter back to storage mode?
best to charge back
Nice looking heli. Does it come with any spare parts? Are spares available where you buy it? Does it have 2 or 3 servos on th cyclic? Could you possibly swap out the Rx for a Futaba or Spektrum and bund it to a better radio? Thanks
seems like people say C186 E129 protocol will bind to it using radiomasters. will give it a try. comes with spare blades only
Nicely explained and thanks for uploading👍
welcome
Fantastic looking model , and a very good explanation and review, Thank you 😎👍👍
Many thanks!
I have bound my MD500 CG Version With Flow Control to my new TX16S. Flown it 4-5 times in my Hanger/Garage. 🤠
Still fine tuning Rates and Expo. It’s a little too Jerky even so.
Do you think Gyro Gains (CH 5?) be turned down on the Head and Tail with added Inputs settings?
haven't done it so far. because i have to update firmware of my TX16s.
A very nice Helicopter, I am waiting for my red and white Version.
congrats :)
do you need to use the auto take off ?I seen a video were the auto take off went out of contorl.they lost it by hitting the stop button. they could of waited the 17mins for the battery to go down . then it would of soft landed.
you can use manual take off using sticks
I have one, im missing my small antenna could i fly without it.
Hi Ali, do you think it´s possible to change the Transmitter to mode 4 or switch the servo leads on the FC roll and yaw?
best regards from Germany
diy of course you can do it. but i have never done it
Sorry if requested, can you do a video of setup & bind your Radiomaster 16s to the C189? thank you
i will try
@@alishanmaox2
i want to know if yuxiang f06 EC135 optical flow can be used at era C1:89 HELICOPTER.
i do not know buddy
Let me know if you find out because the optical flow for this is trash from rc era
Hi I was wondering if you could help me with my one i did everything the manual said and I did the ato take off and it just flies away so I did the ato stop and I did it all over and it still flies away so can you please tell what is wrong with it please.
calibrate the gyro before taking off
Nice Ali. Hoping you would be doing a review on this soon. Shame optical flow was left out. I would imagine they will add optical flow on the next version of it. 🤠
possibly the production versions have it
It have barometer.@@alishanmao
Amazing looking helicopter
Thanks buddy 👍😀
Sorry if I missed it, but what control mode are you flying on? Mode 1 or mode 2?
mode 2
How do i bind it to remote again the Manual doesn't help
Nice job ali i am waiting 11/11 for this beauty
Coming soon
LOVE TO THE HANNEL
Would that extra port be able to power a tiny 5.8ghz FPV cam?
Should be but all you will get jello filled videos because the main rotors make lots of vibrations
@@alishanmao Ah good point, yeah it might not be as usable as I imagined it.
wich is better ERA C189 MD500 4CH Scale or ESKY 300V2 RC Airwolf Helicopter?
Both are good helis. Only thing is which one are you fan of?
As for finding protocol for Tx16s. I know it is a lot of work, you could just try to bind to each one until you find the one that works. A lot of work I know, but possible
Try the protocol e129 sub protocol c 186 on your ts16.
@@andrewberdo3903 thanks 👍. Will try with the 4:1 multi module in my Frsky X12S.
My boxer transmitter only came with e129 protocol. I got the drone shop to download sub protocol c186 of open companion
@@andrewberdo3903 thanks
Very fun, is this a collective or fixed pitch ? 😀
collective given that blades change pitch
Thanks a lot !! So it is not recommanded to fly indoor or is it possible though ? 😀
@@alishanmao Will you make a video about the Flywing Squirrel AS350 H1 GPS system 500 size scaled heli sold by RC Going ? 😀
@@aureliusprimus I just received it but as we are leaving China and moving to another country, today I shipped the AS350 to Shipper and it will be on the ship to our new destination. probably i can post a video from a new place where we will move after I receive it after a month or more. so you gotta wait. no choice. right now i can't do anymore videos. I just have videos scheduled till 3rd November. 2nd november we will fly out. all our luggage is gone, rest is packed and we are just waiting.
@@alishanmao I understand my friend.
Do you like going to another country or were you forced to leave China? You don't know which country will welcome you?
Frankly, you should come to France, you would no longer have any moving worries ! 😀
Which one do you prefer? RC ERA MD 500 or YUXIANG EC 135?
MD500. its better than EC135
@@alishanmao Thank you! And congratulations for the nice review. Always excellent!
heres the video i found in youtube binding T-lite TX. I hope this will help.
thanks
Very nice 😊
Thank you! Cheers!
Which optical flow module fits it?
no idea. they will release one
It is possible to change Mode1, Mode 2?
have not done it, should be possible
Anyone know where you can buy spare battery packs for this helicopter?
Check here: bit.ly/3Vn2CbI
So I finally made mine a "6ch" heli but I changed the esc to with the blade apache esc. Which I have a spare of. (You don't have to do this if you can find the signal pin for tail and main on the original esc, i just don't have enough time) and for the flight controller I used my spare Trex 150. Now you cannot get usable negative pitch because there's just no room for the swash to go down, but fine by me, it's a scale heli. But what I'm left with is an md500 that can easily do realistic maneuvers, because it doesn't have self leveling. Now the easiest way to do this is literally put the omp m2 flight controller and esc. And one last important thing is make sure you don't have negative pitch curve, because the swash plate doesn't have enough space to go down. As for battery, I went with the original for now all because of simplicity and I have 3 already. Once the battery is done I'll change the plug to xt30
One of the reasons why i changed the flight controller, is that this heli actually is bad flying backwards. You could try it. If you fly backwards, the heli will try to pitch forward again. And it's annoying because when you are trying to even just hover, if you correct the heli to pitch back, it will pitch forward. It likes forward flight. But for some reason, the flight controller gets confused when I fly backwards.
good work :) have fun
Make some videos on all that please
@@jdnic1make videos of the upgrades please. nobody has any info for upgrading this heli except one person on youtube who is horrible at responding
your RC robot is cute, what is the brand of this robot ? and I like your RC heli demo
used to be. discontinued long time ago. XK brand
Thanks for the video, can we put the remote control in mode 1
you can buy one in mode 1. to change i am not sure
I got the answer from a RUclipsr.
I finally found how to switch the transmitter to mode 1! You must push the mode 2 throttle trim up and hold it in this position while turning on the transmitter. then we release the trim button and push the right stick to the high position then to the low position. and the transmitter is in mode 1 and it will remain so each time it is switched on. To return to mode 2, it's the same operation except that you activate mode 2 by pushing the left stick to the high position, then to the low position.
@@alishanmao
@@53Whiteeagle8 Thanks for the info. Glad it worked
Hi sir do they sell parts or parts replacement electornics, mechanical, spares etc ? where do you buy them[parts] ? thank you
bit.ly/48l8jhs
you can find parts there
A salam aleikum. Great flight brother. At least this one have a normal tx😂. Thinking abouth getting this one. Thanks for this upload!
No problem 👍 the link is waiting in the description :) and here: bit.ly/48l8jhs
@@alishanmaothank you for the link👍
sunset MD500 ・・・ it is so cool!👍 it is E129 Protocol (subProtocol c186).
Thanks for the info! I will try it right away
Many guys have a "fly away" is there any fix solution? Mine fly 5 times fantastic but at 6 of auto start its fly away impossibel too hold with sticks down or up !Luckily it hits a big tree!
no idea. mine never flew away
Nice demo sir I’ve just bought one with 2 batteries £150 all in.. Red one not in stock so gone camo 🤞🤞👍
Enjoy it
I like it, but I wish it was available in the Kern County Sheriff livery.
you can repaint it
What wcale is it?
I have just Isolated the Control Boards Stack off the Frame with double sided 3M Foam Tape to lower Vibrations getting to Gyros. It helped smooth it out by 25-30%? Flys a little Smoother indoors. 😊
thanks for the tip
Post a video of it
Please
The original design of this helicopter aka "Little Bird" was made for the CIA and special forces by Hughes Aircraft of Howard Hughes fame. Bell helicopter merged with Hughes in the 1980s but the original design of the little bird has not changed beyond improved turboshaft motors
thanks for the info
The OH-6 was initially made as a light observation helicopter to scout for troop carrying Huey’s and attack aircraft. The CIA did use a Modified OH-6 with a muffler type design on the exhaust nozzle to suppress the noise and added a 4 bladed tail rotor and a 5 bladed main rotor and named it “the quiet one”. Hughes Aircraft Merged with McDonald Douglas not Bell in the 1980s. HUGHES aircraft designed and produced the OH-6 loach and then the HUGHES 500 - the civil model. Hughes aircraft also designed and built the AH-64 Apache in 1997 MD merged with Boeing which kept the rights to the OH-6 and AH-6 Littlebird and of course the Apache.
MD helicopter became its own thing and kept continued to make new models of the Original Hughes 500. Boeings version of the MD500, the OH-6X is more powerful and more sophisticated than the current MD500 with a 6 bladed main rotor and 4 bladed tail rotor and it’s even capable to fly unmanned and can be controlled by the front seater of the AH-64E Guardian.
If this had a non stabilised mode I would buy it in a second!
its still very good
Thank you for your review 😊
My pleasure 😊
I saw another review on this bird. It too did not have the optical flow even though in the web description it states that it has optical flow. So WTF is up with that???
That is a good question, if it is advertised as beginner friendly with that as the bid attraction, it should come with it equipped
i believe the samples sent to Reviewers like I got one and i believe captain drone did a review of it before mine. those samples for reviewers do not have optical flow but mass produced ones may have it. anyway i like it without optical flow
The extra port is for an optical flow sensor. No idea why they didn't install one.
maybe to reduce costs and programming LOL
Very nice rc heli sir..😊
thank you
mode1 은 없는건가요?
should have. talk to seller
Wish mine would fly like this one😢. Mine would just spins up a little before cutting off by itself. No idea how to fix it so it now just sits on the shelf.
why not contact the seller because it might be faulty
Don’t know why, but mine will Back up at a 45 deg. angle and go quickly Right When I input Left AIL. 20-25% Expo. Going to Reduce Expo further because if I push past Expo quickly I can Catch the abnormal right/rear shooting off and go Left and forward like I want it to do. So thinking reduce Expo further and maybe the Control will Catch that un commanded movement quicker. More precision….? Who knows. Trying to eliminate that strange opposite movement. A little Risky in a 12 ft square area with walls. 😮
you are not flying with stock radio?
@@alishanmao EdgeTX TX16S
Looks great, flys great, be really great if they did it in a 450ish size!
That would be cool!
This is 300 size or 250 size
Any idea why some of them take off up to the moon and are almost impossible to land?
LoL no idea. Maybe the AI is too Intelligent? 😜
I wish it bind with XK 6 transmitter...
i do not know
@@alishanmao I checked but unfortunately no...
ahh I have seen videos of you fly a lottt of rcs in this location.
well finally we are saying goodbye to this place for good. hope you will see new places for new videos
If the top of that hill actually goes back down again.... You would be in for the ride of your life if you flew past those trees on a windy day....😂
Man I'm still waiting on mine 😂 it got lost in transit
congrats. have fun
السلام alaikum Ali bhai I want to buy this heli I'm from pakistan
you can get it from the link in video description or you can get it from my dubizzle when i post it for sale
OK brother thanks
I LIKE THESE CAUSE THEY SCALE BUT TO MANY PROBLEMS & FRUSTRATION WITH THESE FOR ME
mine is still doing very well
@@alishanmaoI'm gonna get another one but which would you suggest the C189 MD500 are the F06 EC135?
I would say go for MD500, its better in many aspects than that dreaded EC135 @@jonspikes4935
@@alishanmao Who you suggest ordering from is Bangood a good place to order from
@@alishanmao I HEARD DON'T ORDER FROM MARKFIRE THERE'S HAVE DEFECTED GYROS
This is a scale helicopter not a 3D one so behaviour about right i think.
absolutely
Are you a Chinese Indian?
No and NO.
Lol
IDK IM HAVING THE WORST OF LUCK WITH THESE HELICOPTERS I JUST GOT A MD500 & NOW IT DOESN'T WORK I TURN IT ON ALL IT DOES IS BEEP NO LIGHT FUNCTIONS ARE ANYTHING IT'S DEAD IDK WTF HAPPENED THIS THE 2ND HELICOPTER GIVE ME PROBLEMS F06 EC135 WENT INTO MODE 1 COULDN'T GET IT FIGURE OUT TILL IT WAS TO LATE & NOW I HAVE PROBLEMS WITH THIS MD500 VERRY FCKN FRUSTRATING & ALL I WANNA DO IS BE ABLE TO ENJOY IT I WANT ANOTHER ONE BUT I DON'T KNOW IF I CAN TRUST THESE HELICOPTERS NO I ONLY FLY SCALE
i believe these companies really need to step up on quality control and customer support, or else they will die soon if they keep on doing sell and forget attitude
Gift one t0 me brother please
Do not purchase through makerfire... I bought one and it was defective and contacted the company about a replacement as soon as it came down to replacement they stopped responding to my emails.. sent them videos pictures etc... And no response.. stay away from the company makerfire..
Sorry to hear that, i know Jack Xie, a good friend. i will send him message with your comment screen shot. they should not treat customers this way. I advise buying from bit.ly/48l8jhs
they are very reliable and i am in touch with them on daily basis. Ben is very responsible and supporting too.
Hello, this is Jack from Makerfire. First and foremost, I want to extend our sincere apologies for the inconvenience you've experienced. We understand how frustrating this situation can be and take your feedback very seriously.
I have reviewed your case with our customer service team. According to our records, you reported an issue with the tail light not working on your RC helicopter. We responded to you on November 6th, requesting a video to demonstrate the problem. We are still awaiting your response.
To expedite the resolution of your issue, please contact our customer service team directly and supply the requested video. We are committed to addressing your concern promptly and ensuring your satisfaction.
Again, we apologize for the inconvenience you have encountered and look forward to your response so we can resolve this issue swiftly.
Sincerely,
Jack
Makerfire Team
Thanks Jack, Please remember, Supporting customers all the way and actively will make you successful in the long run. @@Makerfire
Thanks bro@@alishanmao
@@Makerfire I got the videos up on my channel.. the helicopter is completely un flyable the gyro is the problem.
I pay for RUclips I don't need to pay for an individual channels once in a while contributions that's greed and it cost u your subscriber thanks for forcing me to figure it out on my own I'm gonna make my own video and I won't charge for it. Hope u make a lot of money because you're gonna lose a lot of subscribers
Real RUclips big dogs don't need to charge for membership you should've done it the way you were doing it before. Good luck I won't be back
if it disappoints you, everyday I am getting new supporting and understanding subscribers. does that make you feel bad that i am still getting subscribers while you have to leave because you do not want to show any understanding to someone who is trying to make his rightful living with his content that takes lots of efforts, time and our own money to bring this content?
Shouldn't you stop charging for whatever work you do, because its greed. you should do it for free too don't you think? because if you get salary then you are greedy too. if you are taking salary and getting paid for what you do and you call me greedy, its called hypocricy. Good luck, and welcome back to my channel any time you want.
Sorry, but I've got to unsubscribe. You're just costing me too much money! 🙂
well you will not get discounted offers if you unsub hahahahah. Thanks mate
@@alishanmao I'd never unsubscribe, you're my favorite RC reviewer. But my wife does not like me watching your videos because it ends up in new toys! LOL
give her some love. she will support you all the way :D @@BobcatBart