MST Performance Intake Install and Comparison. Best Sounding Intake for the GR Yaris?
HTML-код
- Опубликовано: 30 сен 2021
- Today we have the follow up video to the unboxing of the MST Performance intake for the GR Yaris. Here we take the time to fit the kit and test what it looks like and sounds like. If you want one then check out the link below:
mst-performance.co.uk/mst-ty-...
Is this the best sounding intake for the GR Yaris?
Music:
Track: Sekai, Spitfya, Rob Gasser - Mistakes (ft. Emily Stiles) [NCS10 Release]
Music provided by NoCopyrightSounds.
Watch: • Sekai, Spitfya, Rob Ga...
Free Download / Stream: ncs.io/Mistakes
My Setup:
Base Playstation 4 with Samsung 850 Evo SSD
amzn.to/2CYCEVQ
Base Xbox 1 500Gb
Elgato HD60 Capture Card
amzn.to/2WN4E6c
Headset:
amzn.to/2OYEACJ
Wheel:
Logitech G29 Standard with shifter.
amzn.to/2UuzTpl
GT Omega Pro Racing Simulator Cockpit
amzn.to/2I3dedF
My Car:
2005 Mitsubishi Evo IX FQ320
Braided Brake Lines
Uprated Brake Disks and Pads
Carbon Badges
LED Light Conversion
Smaller Battery
1996 BMW 316i
Ebay Coilovers
Ebay Top Mounts
Ebay Hydro Hand Brake
Sparco Bucket Seat
Drfitworks 5 Point Harness
Welded Diff
Shoes:
Adidas XLT Kart Boots in gold and black.
www.demon-tweeks.com/uk/adida...
Gloves:
Adidas XLT Kart Gloves in gold and black.
www.demon-tweeks.com/uk/adida...
All Edited on MacBook Pro with Final Cut Pro and Shot on iPhone 
Авто/Мото
Awesome video! Thank your so much 👍
Thanks so much for the help installing this!
Great video, very well explained and not rushed.
Installed this today. Greatly helped by this video. Doubt I would've been able to do it with the instructions alone. Thank you!
Thank you for the feedback! Glad I could help!
Thanks for making this. Aiming to do mine at the weekend. Nice one
No worries. I hope this helps you do yours abit easier!
Thanks for making this video. I have the All Type Fabrication intake coming and I was worried about those rear bolts being a nightmare too. 👍 Your intake sounds awesome!
They weren’t easy to get too. The space is limited in the engine bay. I definitely advise to remove the stock air box and engine cover for extra room, then come in from the right side of the engine as you look at it from the front.
@@FaithlessEmoRacing Duly noted, thanks for the tip!
Just finished, thanks a million! Took me 4 hours or so. Last half hour was just me obsessing if I've tightened everything enough, alignment, if the silicone parts have been pushed in far enough etc. Happy with the sound. The increased noise noticeable than I imagined especially with a loud exhaust, but noticeable nonetheless and I'd do it all over again if I had to
Thank you for the comment. Check out my Santa Pod video for what happens if it’s not tight enough! 🥴
Thanks for making this video!!!
Thanks for the video brother! Helped a lot.
Glad it helped. Thank you for the feedback.
Instructions weren't great. Couldn't have done it without this video
Thats great feedback and really helps me know im doing a decent job!
Tip for working in back of engine bay or anywhere tools, nuts or bolts can fall down. Stuff or lay a rag in behind to cover the drop so that anything falling will land on the rag and easy to recover. - great video and thanks for sharing your experience.
This is a very good tip! I did the same when I recently fitted a CoolerWorx short shifter. You have a hole in the middle of the transmission tunnel and very easy to loose things down there so i put a microfibre towel there to catch anything!
nice video mate
I'll have to get one of these bad boys!
Can totally recommend.
Installed today and this video was EXTREMELY helpful 👍👍👍 thanks mate
That intake bolt was so difficult to remove lol
I’m glad it was a help that’s why I made the video. And yes that boot was hard to get off. I almost gave up!
@@FaithlessEmoRacing huge help! Yeah it literally took about an hour and multiple tools tried before I managed to get it out. Funny thing, once it moved a little I could remove it with my hands 🤷♂️
@@RobertBaliva yeah I struggled and lost two ratchets. But as you said once it was loosened I did it with my hands.
@@FaithlessEmoRacing haha yeah saw that in the video, glad you didn't edit that out as I was extra careful not to drop anything because of that. How'd you end up getting them out??
@@RobertBaliva I dropped my ratchet trying to install and it literally disappeared :(
Great video, nice and clear installation. The background music is a little loud.
Thanks for the feedback, yeah I’m working on trying to get the right volume levels on the BGM.
Interesting, thanks 👍
That looks and sounds so good 😍 I was expecting it to be about £700 but it's about half that. Bargain
Yeah I was really impressed. Seems to improve throttle response too and sounds great.
Good video, thanks! Would like to hear it from stand still with the bonnet closed and a slow/fast drive by! 👍
I’m hoping to sort a video showing that, weather permitting.
Nice sound. Shock it is on a standard bov. I imagine on Turbosmart or other it gives hell much better effect :)
Cool video I like your content I got your info today I was in the Mercedes iv got a bmw ordered and might have very soon was thinking of doing some comparisons etc and adding mods to my Mercedes might need some tips etc on how to create?! Thanks Dave
Hey there David. What BMW have you ordered? If you ever need any help with mods or tips then give me a shout on Instagram etc and im happy to help! Maybe even make a video!?
Like the vid. Have you seen the evolve intake?
Yeah I watched the Evolve intake through its whole process. Its just too much money for me!
I have a all types fabrications air box just because was fair price and Australian made and made quick delivery. Same basic information. Sounds great! I found the sweet spot to make turbo flutter haha build up boost better in 3rd 60km till you get the idea, and slowly back off the throttle and slowly. It won't activate the bov. Back off the throttle too fast it will let all the air out the bov
Ps I have few videos of my sounds haha
And also you can monitor the intake temps and charged air temps with a obd2 bluetooth device using torque pro app
Yeah I have found that it does that in third easiest too. Tbh I love going half throttle and getting that induction roar, build a little boost then backing off.
I want to get a OBD2 reader so I can read some of the info. It’s on the list of things to do.
Nice video mate, does this intake give u much turbo flutter noises? looking into which intake to get and saw this video!
Yeah you get some great noises. I’ve alway getting compliments on the sounds my car makes.
If you hold half throttle in third about 3,000 rpm gives you a nice bit of flutter.
Thanks for the awesome video. Made my task easy..
How did you reconnect the vacuum sensor? Mine has the check engine light on and I still cannot figure it out.
Im glad i can help! If you check at 17:51 you can see everything i put away and the sensor was one of them! I didnt reconnect it and has been fine for the last 12,000 miles! maybe try a disconnect battery and reconnect?
Thank you so much for this video, really helpful! I just fitted mine and ran into a few problems. The nuts that the maf bolts to are too tall and the oring doesn’t seat in the bore. What did you do with the part that clips into the main pipe behind the engine (you have to remove it and the lower M8)?
Would you also mind clarifying whether you had to plug the vacuum sensor at the front of the stock air box after this video was made?
Which section are you referring to in the first section? If you put the time stamp on the section in the video I will figure it out.
As for the vacuum sensor I left it connected to the old air box. Never had any issues in 10k miles.
Did you ever have an issue with the vacuum module being deleted? I reverted back to stock intake cause my car kept throwing a check engine light because of that module being disconnected
Great video! Question though, did you not have to refit the vacuum sensor that plugs into the connector you mentioned taping up? Just fit one of these kits to my GR and had a check engine light until I refit the sensor.
Cheers! Keep up the good work
Thank you for the support. That’s why I refitted the sensor. I know modern cars tend to freak out when any kind of sensor that was there isn’t fitted. That’s why I just taped it up and kept it out of the way.
@@FaithlessEmoRacing Cheers, I interpreted the video as you just taped the plug up. Even during your sum up it looked like the sensor was on the desk with the rest of the removed parts but it’s good to know that other people reconnected it. As you say in your video the instructions aren’t the best.
Did your car feel immediately faster once you had fitted the Whifbitz exhaust and this intake or did you only real feel the benefit once you had it mapped?
Any luck bro? Just guna fit mine today too
looks great, you should do a Dyno test to see if it improves the power or does the hot air under the bonnet take away the performance, better still, get a grill and put it on the bonnet over the air intake, definitely get a little more sound and would at least get 3-5bhp. .
I would love to do a back to back dyne test but just don't have access to one I can run the stock box and then change it over and run the MST one in the same day.
But if I do see some time at my local dyno I will get it on there.
It does 12 to 14hp
Hey mate, just got mine in the mail. Just to clarify did you plug the vacuum sensor back thats shown on figure 5 in the instruction sheet? I'm actually having trouble unplugging it and if I don't need to that would help me a lot haha. Cheers
Just checked. If you see 5:02 in the video the vacuum sensor comes off with the length of pipe at that step. Hope that helps?
16:45 if your just here for the sound
Hello! Thank you for this video!
How's the car doing with MST Intake??
Problem with stock ecu? Does the engine run well? Carburetion problems or empty?... thanks you
It's been a couple of months and one service later by Toyota and still doing great. Toyota didn't have a issue with it. No issues with the engine running, still pulls as hard as before if not harder. Zero issues!
@@FaithlessEmoRacing Very very well! 😁👍 MST is a good intake at good price!
In addition to having no problems, it is also important to have a good power gain.. 😁 from the MST dyno tests the results were good!
Thank you very much! I want it 😁👍
... P.S: Happy New Year 🥂🥂
Great video. How did you get these screws out behind the engine ? Mine are impossible to get them loose. Any tips please
They are tricky. My best advice is take the engine cover off (just pull off) and then come in from the right as you look at the engine.
@@FaithlessEmoRacing thank you so much. Tried all angles and they won’t budge. WD40?
You can try some penetrating fluid like WD40 to help loosen it. Won’t hurt. It is the bolt that almost made me give up!
how did you mount the camera for the incar shot?
If you check my other videos you find one where I fit a seat mount from Tegiwa. That’s what I used.
Is the pfiew sound on shifts due to the filter? I always thought they where blowoff valve sounds
The sounds are there already. But they are louder and more noticeable with this air filter.
Hey there 👋 it's good video .I get one set for my GR Yaris too.
But I can't remove the intake hose as well , than I connect with Mst MAF sensor hose with original intake hose ..
I don’t think you can use the stock hose as it’s a different length and direction. I found removing the engine cover (just pops off) gives enough room to get done the back of the engine!
@@FaithlessEmoRacing I connect with 4 inch silicone hose 76-89mm ,it's can install as regular but I'm know not the proper way.. hahaha
But your video is help alot , better than manual instructions.. lol 😂 thanks again
Don't suppose you know whether the Airtec/Wagner/Foresight elbow will fit to the MST piping?
I’m unsure. I’m hoping to try one sometime this year, funds willing.
When you installed the MST, did the engine brake on your car almost disappeared? I installed mine and the car has almost no engine braking anymore. And that feels very strange? 🤔 btw great video, it just took like 30min thanks to your video :))
I have not noitced any diminished engine braking since fitting the intake. Maybe a placebo?
@@FaithlessEmoRacing I hope it is placebo :/
that sounds great is that the standard bov too?
Yeah that’s the standard BOV. I do have a Garage Whifbitz exhaust.
was the lady backing up in the land rover about to complain? :D
Lol. She didn’t complain, mostly was wondering what the hell I was doing!
Hello, do you leave the air intake control valve plugged in or remove it? I already have the Mst intake installed. I left the valve plugged in and the car shows an error on the diagnostics.
I’ve removed it. I’ve had no errors. You may get a error as the car can see it attached by not working correctly.
@@FaithlessEmoRacing Thanks, I'll try to disconnect. the problem is that the error cannot be deleted
I'm getting my GR Corolla hopefully next month do you think this unit would fit on that car?
Is that a tattoo of a pentagram on your arm?
This kit won’t fit the GR Corolla. But I’ve seen on the MST social that they have made one for the GR Corolla. Send them a message and say you saw this video and they should be able to sort you out!
It’s not a pentagram, but a Heartagram.
@@FaithlessEmoRacing thanks for the info you did a good install job very easy to follow.
Did it make much difference in performance?
Personally I'd much rather have a gr Yaris than the gr Corolla any day of the week I prefer small Nimble cars I used to own an Ariel Atom.
Awesome! Do you have a discount code?
I don’t I’m afraid. Only a small channel. But drop them a message or email and say you seen my video and they might be able to help.
@@FaithlessEmoRacing great content anyway 😄😄 got the ap carbon mudflaps thanks to you 😀💪
@@sebbebo thank you for the support!
Did it feel like it gave more or less power, of did it just improve the sound? 🙂
It’s hard to say without back to back dyno.
I would say it seems more eager to pull than before though.
@@FaithlessEmoRacing Thank you! Im thinking of buying the same intake, so that's why I was curious
Personally I think it’s a great intake for the money. Very well built and opens up the car abit more.
Only minus point was the instructions were great.
@@FaithlessEmoRacing I think so to! Thanks for the reply 🙂
Did you fit the turbo elbow or just the induction
The whole kit you see in the box. I don’t believe I had what’s is classed as the turbo elbow?!
Ah ok. I've ordered the same kit but with the turbo elbow. Good video by the way. I'll be watching again when mine arrives 🤣
Well I’m glad this helps. If you get stuck. Reach out on instagram and I can always help!
Did you fell a difference in power?????
I wouldn’t say I felt more power, but the engine felt more urgent and more willing to go!
If you check Tegiwa’s video they back to back compare this intake and find good improvements.
No music in background next time pls ;)
Check out my other video which is just pure sound and no music.
Dump the stock music.
one of.the worst mechanic song