I have the same problem with my fronts. Just ordered a pair of load equalizers and once installed I'll let you know! I think this will work......thank you so much!
Thanks for the video. Just added new turn signals to my 2000 Heritage, and had the same problem. Was thinking I wired them up wrong, etc., and was about to rewire them when I Googled the problem and found your video. It saved me countless hours, and a good amount of money. BTW. Also read in the resistor instructions that they can get really hot, but I'm sure that's when they have current for longer periods of time as they are general use components. Our turn signals are off much more often than they are on, so likely won't get overly hot. Thanks again.
Thanks for the video... people in other videos stated that those load resistors get very hot and that they need to be installed in the open and away from stuff that can be melt down. Did you had any problems by installing under the seat? I am trying to see if I go the way of load resistors or electronic relays to fix that fast blinking of LED signals.
Thanks alot I did the relay trick worked for a week got new from LED sleek fitting blinkers on my 99 sporty with LED rear front flashes back don't just constant I been all through my harness and everything testing wires I'm gonna try this 🤘🏻
I thought load resistors where only for hyper flashing? I just put on a integrated rear led tail light and my turn signals just stay on but the hazards work just fine blinking together. Did you experience the same thing I have a 2000 dyna
that module you tapped into is not the stock turn signal module it is a run--turn--brake aftermarket that plugs in line between connectors if you had the stock lights it came with red lenses you defeated its purpose and added lights you can't see from a distance
hello i have the same problem with my bike, it wont blink at all, it just stays on all the time except the hazard light, than all the blinkers go on together...my question did u change the front lights too? or are the resistors only for the rear lights or does it works for both rear and front?
I have a similar problem in my 2007 CBR125R, i changed to LED signals and at first they all 4 were lighting up, i took out the power from the indicator bulb on the dash, they work now, but they are on solid. im waiting for resistors to see if they start blinking. And i also do have a new Relay for them but it didnt change too much. Any tips what can help if the resistors dont help me?
Кино
Thanks, Joe, for the video. It fixed my 2000 Electra Glide Classic.
This helped me figure out a relay issue with swithcing to led on my 87 fxrs. Thanks!
Thanks man worked for me on a custom softail build
This also worked for my 03 Sportster, thanks a bunch man!
How did you wire yours in I can’t get it to work
Nice job sir, nice ride as well.
Hi I have a 883 and a 2003 Element!! Nice video!!
Great simple video. You da man! Subscribed!
Nice sound !!
I have the same problem with my fronts. Just ordered a pair of load equalizers and once installed I'll let you know! I think this will work......thank you so much!
I have the same issue... Please keep us posted
I bought same kit. Works great. 2000 nightrain. Wal mart. Sells them. Thanks for your video.
Thanks for the video. Just added new turn signals to my 2000 Heritage, and had the same problem. Was thinking I wired them up wrong, etc., and was about to rewire them when I Googled the problem and found your video. It saved me countless hours, and a good amount of money. BTW. Also read in the resistor instructions that they can get really hot, but I'm sure that's when they have current for longer periods of time as they are general use components. Our turn signals are off much more often than they are on, so likely won't get overly hot. Thanks again.
Except for being on top of a 250+° engine. They could get very hot
I haven't had problems.
Joe, did you also replace the front turn signal bulbs to led also?
these bikes dont have turn signals?
Thanks for the video... people in other videos stated that those load resistors get very hot and that they need to be installed in the open and away from stuff that can be melt down. Did you had any problems by installing under the seat? I am trying to see if I go the way of load resistors or electronic relays to fix that fast blinking of LED signals.
Enrique Ayala I haven’t had any problems
Thanks alot I did the relay trick worked for a week got new from LED sleek fitting blinkers on my 99 sporty with LED rear front flashes back don't just constant I been all through my harness and everything testing wires I'm gonna try this 🤘🏻
Did it work?
@@thecadillacoftokyo8788 nope ended up putting flashers in
Where did you get tje flashers from?
I thought load resistors where only for hyper flashing? I just put on a integrated rear led tail light and my turn signals just stay on but the hazards work just fine blinking together. Did you experience the same thing I have a 2000 dyna
Danny Rios my 99 dyna does the same thing with the integrated tailight. Find a solution yet?
Same problem on my 03 fxdl
What did you use to plug the holes from factory set up?
They are just normal plugs available at your local hardware store
how do u know which resistor to buy?
that module you tapped into is not the stock turn signal module it is a run--turn--brake aftermarket that plugs in line between connectors
if you had the stock lights it came with red lenses you defeated its purpose and added lights you can't see from a distance
I have a 97 ultra classic. Mine doesn't quite look the same under the seat.
Was the built light an LED? What is your front turn signal? Regular or LED
If the front was also LED do you think you would need a total of four resistor? One for each light?
right now I have LED but I had incandescent before. this works for both applications
Dude where did you get those plugs for holes on rear fender?
Haha.. they will be at your local hardware store.
Where did you get that air filter assembly from, do you have a part number?
www.amazon.com/Kuryakyn-9549-Black-Chrome-Cleaner/dp/B0068FVYXS?th=1
I tried this and still just get a solid blinker on my 98 sportster anyone have that issue ?
hello i have the same problem with my bike, it wont blink at all, it just stays on all the time except the hazard light, than all the blinkers go on together...my question did u change the front lights too? or are the resistors only for the rear lights or does it works for both rear and front?
The resistor will fix all problems. at one point I had incandescent in the front an LED in the back but now I have LED for both
@@joematarazzo533 you think you would need a total of four resistor? One for each light?
LoenMontefusco just 2
take care these may become very hot whenever using the turn signals.
I have a similar problem in my 2007 CBR125R, i changed to LED signals and at first they all 4 were lighting up, i took out the power from the indicator bulb on the dash, they work now, but they are on solid. im waiting for resistors to see if they start blinking. And i also do have a new Relay for them but it didnt change too much. Any tips what can help if the resistors dont help me?
Resistors are the only think I know you can use.
@@goodfellasmerch Okay, thanks for the tip!
I have a 2000 883 sportster the led lights I had installed months ago now the turn signals don't work please help
david stanton Take it to a mechanic.
I’ve got an 85 xj700 I’m hoping this works for me
Does wattage matter? Amazon has (3) listed. 27w 10w and 5w all 12v
They get ridiculous hot. You want them somewhere that gets air
Did not help on my 99 eletra glide
Hey bro I got a 00 classic and would love to follow you on Instagram if you got one. Let me know
@joeybear12 / @goodfellasmerch
It doesn’t look like u need a turn signal on that thing Because it doesn’t look like you drive it