I have a similar problem in my 2007 CBR125R, i changed to LED signals and at first they all 4 were lighting up, i took out the power from the indicator bulb on the dash, they work now, but they are on solid. im waiting for resistors to see if they start blinking. And i also do have a new Relay for them but it didnt change too much. Any tips what can help if the resistors dont help me?
that module you tapped into is not the stock turn signal module it is a run--turn--brake aftermarket that plugs in line between connectors if you had the stock lights it came with red lenses you defeated its purpose and added lights you can't see from a distance
Thanks alot I did the relay trick worked for a week got new from LED sleek fitting blinkers on my 99 sporty with LED rear front flashes back don't just constant I been all through my harness and everything testing wires I'm gonna try this 🤘🏻
I have the same problem with my fronts. Just ordered a pair of load equalizers and once installed I'll let you know! I think this will work......thank you so much!
hello i have the same problem with my bike, it wont blink at all, it just stays on all the time except the hazard light, than all the blinkers go on together...my question did u change the front lights too? or are the resistors only for the rear lights or does it works for both rear and front?
I thought load resistors where only for hyper flashing? I just put on a integrated rear led tail light and my turn signals just stay on but the hazards work just fine blinking together. Did you experience the same thing I have a 2000 dyna
Thanks for the video. Just added new turn signals to my 2000 Heritage, and had the same problem. Was thinking I wired them up wrong, etc., and was about to rewire them when I Googled the problem and found your video. It saved me countless hours, and a good amount of money. BTW. Also read in the resistor instructions that they can get really hot, but I'm sure that's when they have current for longer periods of time as they are general use components. Our turn signals are off much more often than they are on, so likely won't get overly hot. Thanks again.
Thanks for the video... people in other videos stated that those load resistors get very hot and that they need to be installed in the open and away from stuff that can be melt down. Did you had any problems by installing under the seat? I am trying to see if I go the way of load resistors or electronic relays to fix that fast blinking of LED signals.
Where did you get that air filter assembly from, do you have a part number?
www.amazon.com/Kuryakyn-9549-Black-Chrome-Cleaner/dp/B0068FVYXS?th=1
Great simple video. You da man! Subscribed!
Joe, did you also replace the front turn signal bulbs to led also?
I've got a 79 yz250 with the mx360 engine in the frame. Built it when I was growing up. 250 engine was blown so I did swap
They get ridiculous hot. You want them somewhere that gets air
how much? how bout 1250. from an old 400 cz motocross racer.
woopie doo
Thanks, Joe, for the video. It fixed my 2000 Electra Glide Classic.
I bought same kit. Works great. 2000 nightrain. Wal mart. Sells them. Thanks for your video.
these bikes dont have turn signals?
I have a similar problem in my 2007 CBR125R, i changed to LED signals and at first they all 4 were lighting up, i took out the power from the indicator bulb on the dash, they work now, but they are on solid. im waiting for resistors to see if they start blinking. And i also do have a new Relay for them but it didnt change too much. Any tips what can help if the resistors dont help me?
Resistors are the only think I know you can use.
@@goodfellasmerch Okay, thanks for the tip!
Did not help on my 99 eletra glide
that module you tapped into is not the stock turn signal module it is a run--turn--brake aftermarket that plugs in line between connectors if you had the stock lights it came with red lenses you defeated its purpose and added lights you can't see from a distance
Thanks alot I did the relay trick worked for a week got new from LED sleek fitting blinkers on my 99 sporty with LED rear front flashes back don't just constant I been all through my harness and everything testing wires I'm gonna try this 🤘🏻
Did it work?
@@thecadillacoftokyo8788 nope ended up putting flashers in
Where did you get tje flashers from?
Thanks dude! That's all I had to do! You rock you sum a bitch!!!
It doesn’t look like u need a turn signal on that thing Because it doesn’t look like you drive it
Hey bro I got a 00 classic and would love to follow you on Instagram if you got one. Let me know
@joeybear12 / @goodfellasmerch
how do u know which resistor to buy?
I tried this and still just get a solid blinker on my 98 sportster anyone have that issue ?
This also worked for my 03 Sportster, thanks a bunch man!
How did you wire yours in I can’t get it to work
Dude where did you get those plugs for holes on rear fender?
Haha.. they will be at your local hardware store.
take care these may become very hot whenever using the turn signals.
Glendale!!!!!!!!!!!!!
I have a 97 ultra classic. Mine doesn't quite look the same under the seat.
Nice job sir, nice ride as well.
I have the same problem with my fronts. Just ordered a pair of load equalizers and once installed I'll let you know! I think this will work......thank you so much!
I have the same issue... Please keep us posted
What did you use to plug the holes from factory set up?
They are just normal plugs available at your local hardware store
Nice sound !!
I’ve got an 85 xj700 I’m hoping this works for me
Does wattage matter? Amazon has (3) listed. 27w 10w and 5w all 12v
Thanks man worked for me on a custom softail build
This helped me figure out a relay issue with swithcing to led on my 87 fxrs. Thanks!
Hi I have a 883 and a 2003 Element!! Nice video!!
1500.00
Where r u located
Tim Merrill Glendale AZ
Want to sell
I don’t think so. Kinda attached to it.
How much
Make an offer
Want to sell
Tim Merrill man, I don’t think I could
hello i have the same problem with my bike, it wont blink at all, it just stays on all the time except the hazard light, than all the blinkers go on together...my question did u change the front lights too? or are the resistors only for the rear lights or does it works for both rear and front?
The resistor will fix all problems. at one point I had incandescent in the front an LED in the back but now I have LED for both
@@joematarazzo533 you think you would need a total of four resistor? One for each light?
LoenMontefusco just 2
I have a 2000 883 sportster the led lights I had installed months ago now the turn signals don't work please help
david stanton Take it to a mechanic.
I thought load resistors where only for hyper flashing? I just put on a integrated rear led tail light and my turn signals just stay on but the hazards work just fine blinking together. Did you experience the same thing I have a 2000 dyna
Danny Rios my 99 dyna does the same thing with the integrated tailight. Find a solution yet?
Same problem on my 03 fxdl
Thanks for the video. Just added new turn signals to my 2000 Heritage, and had the same problem. Was thinking I wired them up wrong, etc., and was about to rewire them when I Googled the problem and found your video. It saved me countless hours, and a good amount of money. BTW. Also read in the resistor instructions that they can get really hot, but I'm sure that's when they have current for longer periods of time as they are general use components. Our turn signals are off much more often than they are on, so likely won't get overly hot. Thanks again.
Except for being on top of a 250+° engine. They could get very hot
I haven't had problems.
Was the built light an LED? What is your front turn signal? Regular or LED
If the front was also LED do you think you would need a total of four resistor? One for each light?
right now I have LED but I had incandescent before. this works for both applications
Thanks for the video... people in other videos stated that those load resistors get very hot and that they need to be installed in the open and away from stuff that can be melt down. Did you had any problems by installing under the seat? I am trying to see if I go the way of load resistors or electronic relays to fix that fast blinking of LED signals.
Enrique Ayala I haven’t had any problems